4G +WIFI Module User Manual Product Name: EV charging system module 4G with WI-FI Manufacturer: Phihong Technology Co., Ltd. Model name: DLWPH-8M, DLWPH-8M-RW Power 5V Power input via USB Type C DC 3.8V for LTE DC 3.3 V for WiFi Energy consumption 200‐500mA Interface USB Type C Support band LTE:B2/B4/B5/B12/B13/B14/B66/B71 WCDMA: B2/B4/B5 IEEE 802.
Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
This module is intended for OEM integrators only. Per FCC KDB 996369 D03 OEM Manual v01 guidance, the following conditions must be strictly followed when using this certified module: KDB 996369 D03 OEM Manual v01 rule sections: 2.2 List of applicable FCC rules This module has been tested for compliance to FCC Part 15.247, 22H, 24E, 27, 90R 2.3 Summarize the specific operational use conditions The module is tested for standalone mobile RF exposure use condition.
Antenna Type External PCB Antenna Internal PCB Antenna Manufacturer Aristotle ublox Antenna Wi-Fi: R-SMA Male Wi-Fi: N/A Connector WWAN: SMA Male WWAN: N/A, External Only Antenna Gain Brand: Aristotle, Wi-Fi: 2 dBi WiFi Model: RFA-25-JP266-79-250 WWAN: N/A, External Only LTE Model:RFA-LTE-JP187-79B300 Wi-Fi: 4 dBi WCDMA/LTE 4.54 dBi B2: WCDMA B4 & 4.54 dBi LTE B4/B66: WCDMA/LTE 2.28 dBi B5: Impedance(Ω) LTE B12: 1.8 dBi LTE B13/B14: 1.8 dBi LTE B71: 1.8 dBi 50 Ohm 50 Ohm 2.
OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.
Industry Canada statement: This device complies with ISED’s licence-exempt RSSs. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Le présent appareil est conforme aux CNR d’ ISED applicables aux appareils radio exempts de licence.
This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed and operated with greater than 20cm between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required.
End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed and operated with greater than 20cm between the antenna and users. The final end product must be labeled in a visible area with the following: “Contains IC: 26049-DLWPH8M”. Plaque signalétique du produit final Ce module émetteur est autorisé uniquement pour une utilisation dans un appareil où l’antenne peut être installée et utilisée à plus de 20 cm entre l’antenne et les utilisateurs.
This radio transmitter [IC: 26049-DLWPH8M] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.
