OWNER’S GUIDE
WIRELESS EARPHONES with ACTIVE NOISE CANCELLING Thank you for purchasing PHIATON BT 100 NC - Please follow the directions, and read the guidelines carefully before use. Please keep the owner’s guide for future reference. - Some functions of the BT 100 NC may not be available when it is paired with certain devices. - The specifications are subject to change without prior notice for quality improvement. Contents 1. SAFETY AND GENERAL INFORMATION 2. COMPONENTS & FEATURES 3. HOW TO WEAR EARPHONES 4.
1. SAFETY AND GENERAL INFORMATION 1) Use a standard USB charging cable (included), with or without a charging adaptor. (5V, over 500mA) * Adapter Not Included 2) Lower the volume prior to listening to audio to prevent potential damage to eardrums caused by sudden loud sound. 3) Listening to loud music for extended periods of time may cause hearing damage. 4) Do not store the device in places with a temperature higher than 113 ℉/ 45 ℃. 5) This product is sweat and water resistant.
2. COMPONENTS & FEATURES COMPONENTS FEATURES - BT 100 NC Stopper - USB Charging Cable - Audio Cable - 4 Sizes of Silicon Ear Tips Noise Cancelling ON/OFF Switch LED Indicator - Stopper - Quick Guide NFC Antenna - Warranty Card (+)/(-)Button Call/Bluetooth Power Button Play Button USB Cover 3. HOW TO WEAR EARPHONES 1) Hold the earphone body with wire dropping down. 2) Gently insert the ear tip into the ear canal. 3) Let the ear tip set comfortably in your ear. 1 2 3 4.
. POWER ON/OFF AND EARPHONE CONNECTION WAITING MODE 1) Power ON/OFF Power ON/OFF ON : 2 Seconds OFF : 2.5 Seconds - Press and hold the [CALL/POWER] Button for 2 seconds to turn the power on. - When turning the power off, press and hold the [CALL/POWER] Button for 2.5 seconds to turn off. (While on an incoming call, you cannot power off the device.) - When turning power on/off, there is a vibration notification that rings.
. PAIRING WITH A ‘BLUETOOTH DEVICE’ 1) Pairing - Turn on the Bluetooth feature with the ‘Bluetooth Device’ you want to connect with the BT 100 NC. 3 feet - Place the BT 100 NC within 3 feet of the ‘Bluetooth Device’ you want to connect. - Press and hold the PLAY Button for over 2.5 seconds with the BT 100 NC power on to enter Pairing Mode. Status Pairing Mode LED Indicator Blue and Red light alternately blinks Voice Guidance Pairing Mode activated Search“BT 100 NC” Play Button for 2.
※ The device will not operate properly if the profiles are not supported equally. Even when the profiles are supported equally, some features may not properly operate depending on the 'Bluetooth Device' specifications. To check the detail specifications of this earphone’s profile, refer to ‘18. SPECIFICATIONS’. For any other inquiries, please contact Phiaton Customer Service. 7. PAIRING WITH NFC 1) You can easily pair the BT 100 NC with a ‘Bluetooth Device’ that has NFC capability.
3) What is ’Auto Mode’? This is a mode used to automatically reconnect both previously connected 'Bluetooth Devices' when the POWER is turned off and back on. 4) Using ‘Auto Mode’ - Within Pairing Mode, press the (+) Button for 2.5 seconds to turn on Auto Mode. - If you press the (+) Button for 2.5 seconds again, then Auto Mode will turn off and switch to Manual Mode. ※ Upon Multipoint Connection, the features operated within BT 100 NC usually operate within the second paired device.
11. LISTENING TO MUSIC (PLAY & CONTROL) 1) Playing Music - Shortly press the PLAY Button once to play music from the 'Bluetooth Device'. - While music is playing, shortly press the PLAY Button to pause the playing music. The music will be played from the paused point when playing music again.
13. USING THE CALL FUNCTION 1) Accepting a Call - When the incoming call tone is heard through the earphones or the incoming call vibration is ringing, Play Button press the CALL/POWER Button. (Adjusting Call Volume: to control the call volume, Press the (+)/(-) Button.) 2) Ending a Call - While on a call, shortly pressing the CALL/POWER Call/Bluetooth Power Button L Side Body Button to end the call.
14. CHANGING SOUND MODE 1) When the BT 100 NC connects with the aptX high quality sound compatible ‘Bluetooth Device’, it connects in aptX mode automatically. (If the ‘Bluetooth Device’ can not support aptX mode, it will be connected with SBC mode.) 2) You can switch to SBC only mode which is less draining on the battery. - Press CALL/POWER Button with (+) Button for 2 seconds when the device power on.
4) Resetting the Device - To reset to factory settings, press the CALL/POWER Button and (+) Button for 5 seconds simultaneously while in 'Pairing Mode'. Operation LED Indicator Factory Settings Purple light lights up twice Voice Guidance After ‘beep’ signal tone twice, “POWER ON, Pairing Mode activated” 17. CONNECTING AND USING THE AUDIO CABLE 1) BT 100 NC can also be used with the audio cable connected as shown in the figure.
2) Earphones - Type: Φ13.5 mm Driver Units - Sensitivity: 100 dB - Frequency Response: 10 Hz ~ 27 kHz - Impedance: 24 Ω - Weight: 7.2 g (0.015 lb) - Mic. for Noise Cancelling 19. PRODUCT SYMPTOMS AND TROUBLESHOOTING 1) The power does not turn on: - Charge the device. If the power does not turn on even after charging, contact Phiaton Customer Service. 2) The device does not charge: - Check whether the USB charging cable has been properly connected with the device.
8) Outside noise is too high or not reduced: - Check whether Noise Cancelling is turned On. - Check whether the right size ear tips are chosen. (Noise will not be properly reduced if the ear tips are not properly inserted or the right size ear tips are not chosen.) 9) The LED Indicator does not operate: - Check whether the LED Indicator feature has been activated. (The LED Indicator feature can be activated by simultaneously pressing the (+) button and (-) Button for 2.5 seconds.
21. IC COMPLIANCE INFORMATION This device complies with Industry Canada license-except RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment and meets RSS-102 of the IC Radio Frequency (RF) Exposure rules.
. MISCELLANEOUS FEATURES 1) Checking Remaining Battery - With the power on, shortly press the CALL/POWER button twice to display the remaining battery indicator (LED).
