User's Manual

STATUS LED & RETEST BUTTON
STATUS LED
5A FUSE
SUPPLIED
5A FUSE
SUPPLIED
+ 12/24 VOLTS
WHITE WIRE
RED WIRE
GREEN WIRE
BLACK WIRE
YELLOW/BLACK WIRE
WHITE/BLACK WIRE
BROWN/BLACK WIRE
PIN - 9
PIN - 1
PIN - 3
PIN - 11
PIN - 10
PIN - 22
PIN - 13
PIN - 12
PIN - 18
PIN - 20
PIN - 6
PIN - 8
PIN - 19
PIN - 7
PIN - 2
PIN - 4
PIN - 21
PIN - 24
PIN - 23
CAN HIGH
CAN LOW
NEGATIVE
DOORS
POSITIVE
DOORS
AUX
RELAY OUT 1
AUX
RELAY
OUT 2
ENSURE THAT ALL WIRES THAT
PASS THROUGH PANEL HOLES ARE
PROTECTED WITH GROMMETS
GROMMETS
CHASSIS
+ 12/24
VOLTS
+24V
+ 12/24 VOLTS
CONNECT TO
RETEST BUTTON
IGNITION
CHASSIS
774 Ri
REMOTE/IMMOBILISER
DPFK 774612/0
PFK 774-102R
Ignition
switch
EXTERNAL
BUZZER
BLUE WIRE
RED WIRE
GREY WIRE
BLUE/GREEN WIRE
ACCESSORY PORT
To be used with
a PFK accessory
RED/
BLACK
WIRE
or
ORANGE WIRE
GREEN/RED
GREEN/WHITE WIRE
BROWN/WHITE WIRE
RED/GREY WIRE
GROUND
NEGATIVE 1
OUTPUT
Option 1Option 2 Pulse
Horn / Headlamp
Flash
Fail - Initial
1 - 30
Sec
1 - 30
Sec
1 - 30
Sec
Drive state
output
Random Sample
Fail
Start of sample
output
Failed to give
random sample
NEGATIVE 2
OUTPUT
NEGATIVE 3
OUTPUT
Part No. 712-800
Part No. 674-850
To PC
CAN
INTERFACE CABLE
(Only for CAN enabled VBS)
WARNING:
DO NOT CONNECT CAN INTERFACE
CABLE WHILE VBS IS STILL
CONNECTED TO THE VEHICLE
Part No. 712-800
CUT STARTER SOLENOID WIRE TO BE
IMMOBILISED AND REJOIN VIA GP RELAY
85
30
GP
RELAY
30A
FOR USE ON 24V SYSTEMS
FOR USE ON 12V SYSTEMS
86
87a
Normally
closed
87
NOT USED
MOUNT FOR MAXIMUM
VISIBILITY.
}
CIRCUIT 1
CIRCUIT 1
CUT STARTER SOLENOID
LINE TO BE IMMOBILISED
AND REJOIN VIA CIRCUIT 1
(20 AMP CAPABILITY)
JOIN INTO
CUT STARTER
SOLENOID
LINE
Normally Closed
Common
STARTER
SOLENOID
WIRE
WIRE HARNESS
INTO THE VEHICLE
PRIOR TO PLUGGING
CONTROL MODULE IN
Battery
Check
Outputs
limited to
100mA
(1)
(3)
(5)
(2)
(8)
(4) (6)
(7)
Anti-tamper Screw caps
are also supplied should
you wish to use them.
Once security cover is fitted,
attach the Anti-Tamper sticker
over the join between the unit
and the security cover.
Once the installation is complete and fully
tested the security cover can be fitted.
Attach to the main casing using the screws
provided.
Anti-Tamper
sticker
Normal < 80 mA
Heating < 1000mA
Sleep 18mA
Power
consumption @ 12V
1
1
2
2
3
5
4
4
5
8mm
15mm
LED states
Flashing Red
- unit not ready
Flashing Orange
- unit heating
Flashing Green
- Give a sample
Green - Pass
Red - Fail
PAGE
2 OF 2
www.autowatch.co.za
Customer Support
27/09/2012
VEHICLE BLOCKING SYSTEM
Override Sense Input
Emergency Override Switch (Optional)
Part No. 720-960
For dashboard mounting drill
a 12mm Diameter Hole
*
*
*
PC INTERFACE CABLE
This USB cable is also used to charge the 740 with the car charger
DPFK 740 / 520
12V CAR CHARGER
(9)
Ensure the 740
WAB is charged,
only use approved
chargers.
(10)
Do not use solvents
to clean the 740
WAB touch screen.
(11)
Installer to place
Anti-Tamper
stickers on
rear of WAB
(5)
Power
Button
USB slot
Finger Print
Reader
18.7mm
D-Shape
Do not store
the 740 where it can
experience excessive
heat or cold.
This will increase the time
for a sample to be taken to
be analyzed by the 740.