OPERATING GUIDE PLEASE READ THIS ENTIRE GUIDE BEFORE BEGINNING
Hereinafter Radio Systems Corporation, Radio Systems PetSafe Europe Ltd., Radio Systems Australia Pty Ltd. and any other affiliate or Brand of Radio Systems Corporation may be referred to collectively as “We” or “Us”. IMPORTANT SAFETY INFORMATION Explanation Of Attention Words And Symbols Used In This Guide This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Thank you for choosing SportDOG™ Brand. Used properly, this product will help you contain and train your dog efficiently and safely. To ensure your satisfaction, please review this Operating Guide thoroughly. If you have questions regarding this product’s operation, please see the Frequently Asked Questions and Troubleshooting sections, contact our Customer Care Center, visit our website at www.sportdog.com, or view our support videos at www.youtube.com/sportdogbrand.
HOW THE SYSTEM WORKS KEY DEFINITIONS The SportDOG Brand Contain + Train system has been proven safe, comfortable, and effective for dogs over 10 pounds. In Containment and Contain + Train modes, the system works by producing a radio signal from the Fence Transmitter through up to 8,600 feet of Boundary Wire. The Boundary Wire is buried or attached to a fixed object to enclose the dog’s Boundary Area. You temporarily define the Boundary Area with Boundary Flags for a visual aid in training your dog.
STEP :: 01 PREPARE THE COLLAR RECEIVER CHARGE THE COLLAR RECEIVER The Contain + Train™ Collar Receiver contains a rechargeable lithium-ion battery. When the unit indicates the battery is low (battery icon on OLED display shows 1 bar or less and Battery Indicator Light flashes red) it’s time to recharge the unit. Average battery life is 168 hours in Training and Contain + Train modes, and 6 months in Containment mode. FOLLOW THESE STEPS TO CHARGE THE BATTERY: 1.
COLLAR RECEIVER INDICATOR LIGHT OPERATIONAL MODE LIGHT COLOR BATTERY STATUS LIGHT FUNCTION SPEAKER FUNCTION VIBRATION N/A Light is solid in color Beeps 1-3 times during beep sequence depending on static stimulation range Light is solid in color setting (2 is the default during beep sequence setting) DISPLAY Unit will display the current battery level, mode setting, and containment stim level if Containment mode is enabled Unit is turned on via power button Green Good Unit is turned on via power but
• The rechargeable lithium-ion batteries are not memory sensitive, don’t require depletion before charging, and can’t be over charged. • The batteries come partially charged from the factory, but will require a full charge before the first use. • When storing the unit for long periods, remember to regularly give batteries a full charge. This should be done once every 3-4 months. • You should expect hundreds of recharge cycles from your batteries.
STEP :: 05 PROGRAM THE REMOTE TRANSMITTER STEP :: 06 MATCH THE COLLAR RECEIVER AND REMOTE TRANSMITTER The Contain + Train™ Remote Transmitter has seven operational modes allowing you to select the best match for your type or style of training. The Remote Transmitter is factory set to mode 1. There’s also one programming mode: Mode V/T (see Change ID Codes on page 15).
SAMPLE LAYOUTS STEP :: 09 INSTALL THE FENCE TRANSMITTER Sample 1: Perimeter Loop (Single Loop) The Perimeter Loop is the most common layout. This will allow your dog to freely and safely roam your entire property (10C). It can also protect gardens, pools, and landscaping (10D). 10C WARNING To avoid electric shock, use the containment Transmitter indoors in a dry location only. Place the Fence Transmitter: • In a dry, well ventilated, protected area (9A).
Sample 6: Wire Loop Attached to Existing Fence (Double Loop) This layout allows you to include your existing fence as part of your layout and keeps your dog from jumping out or digging under it. It reduces the amount of wire which will need to be buried. Run the wire from the Fence Transmitter to A, A to B, B to C, C to D, D to E, E to F, make a U-turn and follow your path all the way back to A, keeping the wire separated at least 5 feet. Twist the wire from A back to the Fence Transmitter.
STEP :: 13 SET THE BOUNDARY WIDTH AND TEST THE COLLAR RECEIVER The Range Switch on the side of the Fence Transmitter has 2 settings. Set the Range Switch to LOW if the amount of wire used for your property is less than 4,400 feet. Set the Range Switch to HI if you used + . between 4,400 and 8,600 feet of wire. The stimulation mode switch should be set to Use the Range Adjuster Knob to set the width of the Warning Zone and Stimulation Zone (13A).
TO CROSS HARD SURFACES (DRIVEWAYS, SIDEWALKS, ETC.) Follow all safety instructions for your power tools. Be sure to always wear your safety goggles. • Concrete Driveway or Sidewalk (14B): Place the 14B Boundary Wire in a convenient expansion joint or create a groove using a circular saw and masonry blade. Place the Boundary Wire in the groove and cover with an appropriate patching compound. For best results, brush away dirt or other debris before patching.
A B C STEPS: 1. With full control of your dog on a lead/leash, have the distraction presented. 2. If your dog doesn’t move toward the distraction, praise and offer a treat. 3. If your dog does react to the distraction, allow him to go into the Stimulation Zone. 4. Help your dog back into the Boundary Area if he doesn’t turn back after 3 seconds. 5. Give treats and praise your dog anytime he comes back into the Boundary Area with or without help. 6. Repeat this process with other distractions.
ACCESSORIES To purchase additional accessories for your SportDOG™ Brand Contain + Train™ system, contact the Customer Care Center or visit our website at www.sportdog.com.
ADDITIONAL INFORMATION TROUBLESHOOTING The answers to these questions should help you solve any problem you have with this system. If they don’t, please contact the Customer Care Center, visit our website at www.sportdog.com, or view www.youtube.com/sportdogbrand for support videos. My dog isn’t responding when I press a button on the Remote Transmitter. • • • • • • • • Check to see if the Collar Receiver has been turned on and the Indicator Light is flashing.
9. Replace the damaged Boundary Wire with new Boundary Wire. 10. Reconnect the Boundary Wire to the Fence Transmitter. 11. Check the Loop Indicator Light. If the Loop Indicator Light is on, test the system with the Collar Receiver. FCC: USA TEST LIGHT INSTRUCTIONS 1. 2. 3. 4. Turn the Collar Receiver on. Hold the Test Light Contacts to the Contact Points. If in Training or Contain + Train™ modes, press a Static Stimulation Button on the Remote Transmitter. The Test Light will flash.
TWO YEAR NON-TRANSFERRABLE LIMITED WARRANTY This Product has the benefit of a limited manufacturer’s warranty. Complete details of the warranty applicable to this Product and its terms can be found at www.sportdog.com and/or are available by contacting your local Customer Care Centre.
MOUNTING TEMPLATE 6.30” LAYOUT GRID 34 1-800-732-0144 WWW.SPORTDOG.
SPORTDOG.
