User Manual
Table Of Contents
- Safety
- Applies To
- Using this Manual
- Safety Alerts
- Illustrations
- General Safety Instructions
- Data Recorder
- Environmental Protection Agency
- Repairs
- Additional Sources of Information
- Cab Access
- Deckplate Access
- How to Open the Hood
- Close the Hood
- Seat
- Vehicle Loading
- Visual inspection while approaching the vehicle
- Daily Checks
- Weekly Checks
- Systems Check
- Emergency
- Controls
- Instrument Panel
- Gauges
- Warning Lights and Indicators
- Warning Lights
- Introduction
- Anti-Lock Brake System (ABS)
- Anti-Lock Brake System (ABS), Trailer
- Axle, Stability Control (Option)
- Axle, Traction Control
- Check Transmission
- Diesel Particulate Filter (DPF) Warning Light
- Differential, Inter-Axle Lock
- Dump Truck, Body Up
- Dump Truck, Trailer Body Up
- Engine BrakeSaver or Transmission Retarder
- Engine, Brake ON/OFF
- Engine, Brake Level
- Engine, Check Engine
- Engine, Engine Block Heater
- Engine, Low Coolant Level
- Engine, Overspeed
- Engine, Retarder (Brake)
- Engine, Stop Engine
- Engine, Wait To Start
- Emissions, Engine Derate
- Emissions, High Exhaust System Temperature
- Fifth Wheel Locked
- Fifth Wheel Unlocked
- Fifth Wheel Slide Unlocked
- Hill Hold (Eaton Ultrashift Plus)
- Lane Departure Warning (LDW)
- Lights, High Beam
- Malfunction Indicator Lamp (MIL)
- Message Waiting
- Park Brake
- Seat Belt, Fasten
- Transmission, Oil Temperature High
- Turn Signal, Left
- Turn Signal, Right
- Worn brake
- Menu Control Switch
- Steering Wheel Controls (Option)
- Exterior Lights Switch (ELS)
- Peterbilt Digital Display
- Display Notifications
- Views
- Menu
- Post Trip
- Dash Switches
- Axle, Automatic Traction Control
- Axle, Diff-Lock - Dual
- Axle, Diff-Lock - Forward Rear
- Axle, Diff-Lock - Steer
- Axle, Diff-Lock - Rear Rear
- Axle, Diff-Lock - Single Rear
- Axle, Inter-Axle Differential Locked (Tandem)
- Axle, Two Speed
- Back Up Alarm Mute
- Batteries, Low Voltage Disconnect (LVD)
- Brakes, ABS Off-Road
- Brakes, Parking Brake Valve
- Brake, Trailer Hand
- Cab and Panel Dimmer Switch
- Dump Truck Gate
- Engine, Brake Level
- Engine, Brake On/Off
- Engine, Cruise Control On/Off
- Engine, Cruise Control Set/Resume
- Engine Fan Override
- Engine, Heater
- Engine, Remote Throttle
- Engine, Shutdown
- Exhaust, Brake On/Off
- Exhaust, Diesel Particulate Filter (DPF) Regeneration
- Fifth Wheel Slide
- Fuel Heater
- Generic Air, Accessory
- Generic, Spare SPARE
- Kingpin Release
- Lane Departure Warning Disable
- Ignition Key Switch
- Lights, Beacon
- Lights, Daytime Running (Override)
- Lights, Flood
- Lights, Flood ISO 3732 Spare
- Lights, Fog
- Lights, Footwell (option)
- Lights, Hazard
- Lights, Spot
- Pintle Hook
- Power Take-off (PTO)
- Suspension, Air Retention
- Suspension, Axle, Pusher
- Suspension, Axle, Tag
- Suspension, Lift
- Suspension, Third Axle Lift
- Trailer Air Supply
- Trailer, Axle (3rd Axle) Lift
- Trailer, Axle Lift Forward
- Trailer, Axle Lift Rear
- Trailer, Belly Dump
- Trailer Dump Gate
- Trailer, Belly Dump Gate Center
- Trailer, Belly Dump Gate Front
- Trailer, Belly Dump Gate Rear
- Trailer, Hotline
- Trailer, Suspension Air Dump
- Winch Clutch
- Steering Column Controls
- Door Mounted Mirror Controls
- Ignition Key Switch
- Exterior Lighting Self-Test (ELST)
- Heating and Air Conditioning
- Cab Accessories
- Driving
- Starting and Operating
- Starting and Warming Up
- Engine Operations
- Transmission
- Hydraulic Brakes
- Air Brake System (option)
- Brake Safety and Emergency
- Retarders
- Axle and Suspension
- Fifth Wheel
- Driving Tips and Techniques
- Stopping the Vehicle
- Antilock Brake Systems (ABS)
- Maintenance
- New Vehicle Maintenance Schedule
- First Day
- First 50-100 mi / 80-160 km
- First 500 mi / 800 km
- First 2,000 mi / 3,218 km
- First 3,000-5,000 mi / 4,800-8,000 km
- Preventive Maintenance Intervals
- Fender Liners
- Lubricants
- Air System
- Dual Air System Function Test
- Air Dryer Maintenance
- Air Tanks
- Air Gauges and Air Leaks
- Air Compressor
- Brake System
- Cab Maintenance
- Safety Restraint System - Inspection
- Cooling System Maintenance
- Windshield Wiper/Washer
- Electrical System
- Engine Aftertreatment System Power Requirements
- Low Voltage Disconnect (LVD) (option)
- LVD Setup
- Fuses, Circuit Breakers and Relays
- Adding Electrical Options
- Maximum Number of Lamps Allowed per Circuit
- Vehicle CAN Bus
- Batteries
- Under Cab Battery Access
- In Cab Battery Access
- Cranking Battery Specification
- Removing Batteries
- Installing Batteries
- Replace Battery Box Cover
- Slow Battery Charging
- Alternator
- Remote Keyless Entry
- Engine Maintenance
- Fuel System
- Frame
- Front Axle and Suspension
- Heater and Air Conditioner Maintenance
- Noise and Emission Control
- Diesel Exhaust Fluid Tank
- Rear Axle and Suspension
- Rear Axle Alignment
- Steering System
- Driveline
- Tires
- Wheels
- Transmission Maintenance
- Hydraulic Clutch
- Specification Reference Charts
- Information
- Glossary
- Index
• Bowl wrench RK61680
•
1" wrench
• New PACCAR primary fuel filter
element designed for this
application
• 2 new O-rings
Start procedure with engine off. Cover any
electrical equipment and wiring that might
get soaked with fuel; diesel fuel may
permanently damage electrical insulation.
To expel air from density-type strainer
elements, soak them in clean fuel before
installing them. Lubricate new O-rings with
clean fuel to ensure a positive seal.
1. Disconnect clip-type electrical
connections from bowl bottom:
a. Disconnect water in fuel (WIF)
sensor from wire bundle.
b. Disconnect electrical heater
sensor from wire bundle.
2. Using bowl wrench, loosen filter
bowl and lower at least 2 inches.
Take care not to damage bowl
sensors on surrounding
components.
3. Slowly remove bowl and filter from
upper filter assembly.
4. Remove the filter element and both
upper and lower O-rings.
5. Install new filter element:
a. Install new upper and lower
O-rings.
b. Install new fuel filter element.
6. Reconnect clip-type electrical
connections to bowl bottom:
a. Reconnect water in fuel (WIF)
sensor to wire bundle.
b. Reconnect electrical heater
sensor to wire bundle.
7. If your vehicle has a fuel blending
valve, turn valve to “Prime.”
8. Prime fuel filter assembly:
• If your assembly contains a
manual priming pump (PX-7
engines) press priming pump
repeatedly until pumping action
becomes firm, or
• Allow the electric priming pump
to prime assembly (non PX-7
engines).
9. Start the vehicle.
For PX-7 and PX-9 engines, idle
for 5 minutes.
10. If your vehicle has a fuel blending
valve, turn valve to “Run.”
Observe fuel filter assembly for leaks.
Dispose of old filter element and O-rings
properly.
Fuel Tank
Frame
WARNING
DO NOT cut, splice or weld frame rails
or
drill through the top or bottom flang-
es of the rails. These operations could
affect frame rail strength leading to a
failure resulting in an accident. Rail
failures resulting from such modifica-
tions are not warrantable. Failure to
comply may result in property damage,
personal injury, or death.
MAINTENANCE - Frame
250 Y53-6113-1A1 (11/20)
5