Instructions

VersiDrive i E3 User Guide Revision 1.03
www.peter-electronic.com
3
1 Quick Start Up
Declaration of Conformity
PETER electronic GmbH & Co. KG hereby states that the VersiDrive i E3 product range conforms to the relevant safety provisions of the
following council directives:
2004/108/EC (EMC) and 2006/95/EC (LVD) (Valid until 20.04.2016)
2014/30/EU (EMC) and 2014/35/EU (LVD) (Valid from 20.04.2016)
Designed and manufacture is in accordance with the following harmonised European standards:
EN 61800-5-1: 2003 Adjustable speed electrical power drive systems. Safety requirements. Electrical, thermal and energy.
EN 61800-3 2
nd
Ed: 2004 Adjustable speed electrical power drive systems. EMC requirements and specific test methods
EN 55011: 2007 Limits and Methods of measurement of radio disturbance characteristics of industrial, scientific and
medical (ISM) radio-frequency equipment (EMC)
EN60529 : 1992 Specifications for degrees of protection provided by enclosures
Electromagnetic Compatibility
All VersiDrive i´s are designed with high standards of EMC in mind. All versions suitable for operation on Single Phase 230 volt and Three Phase
400 volt supplies and intended for use within the European Union are fitted with an internal EMC filter. This EMC filter is designed to reduce the
conducted emissions back into the supply via the power cables for compliance with the above harmonised European standards.
It is the responsibility of the installer to ensure that the equipment or system into which the product is incorporated complies with the EMC
legislation of the country of use. Within the European Union, equipment into which this product is incorporated must comply with the EMC
Directive 2004/108/EC. When using an VersiDrive i E3 with an internal or optional external filter, compliance with the following EMC Categories,
as defined by EN61800-3:2004 can be achieved:
Drive Type / Rating EMC Category
Cat C1 Cat C2 Cat C3
1 Phase, 230 Volt Input No additional filtering required
Use shielded motor cable
3 Phase, 400 Volt Input Use External Filter No additional filtering required
Use shielded motor cable
Note
Compliance with EMC standards is dependent on a number of factors including the environment in which the drive is installed,
motor switching frequency, motor, cable lengths and installation methods adopted.
For shielded motor cable lengths greater than 100m and up to 200m, an output dv / dt filter must be used (please refer to the
PETER electronic Stock Drives Catalogue for further details)
Compliance with EMC directives is achieved with the factory default parameter settings
All rights reserved. No part of this User Guide may be reproduced or transmitted in any form or by any means, electrical or mechanical including
photocopying, recording or by any information storage or retrieval system without permission in writing from the publisher.
Copyright PETER electronic GmbH & Co. KG © 2016
All PETER electronic VersiDrive i E3 units carry a 1 year warranty against manufacturing defects from the date of manufacture. The
manufacturer accepts no liability for any damage caused during or resulting from transport, receipt of delivery, installation or commissioning.
The manufacturer also accepts no liability for damage or consequences resulting from inappropriate, negligent or incorrect installation,
incorrect adjustment of the operating parameters of the drive, incorrect matching of the drive to the motor, incorrect installation, unacceptable
dust, moisture, corrosive substances, excessive vibration or ambient temperatures outside of the design specification.
The local distributor may offer different terms and conditions at their discretion, and in all cases concerning warranty, the local distributor
should be contacted first.
This user guide is the “original instructions” document. All non-English versions are translations of the “original instructions”.
The contents of this User Guide are believed to be correct at the time of printing. In the interest of a commitment to a policy of continuous
improvement, the manufacturer reserves the right to change the specification of the product or its performance or the contents of the User
Guide without notice.
This User Guide is for use with version 3.02 Firmware.
User Guide Revision 1.03
PETER electronic GmbH & Co. KG adopts a policy of continuous improvement and whilst every effort has been made to provide accurate and up
to date information, the information contained in this User Guide should be used for guidance purposes only and does not form the part of any
contract.