Specification Sheet

ManualsBrandsPermatex ManualsAutomotivePermatex 09103 Windshield Repair Kit

Toll Free: 87 PERMATEX

(877-376-2839)

10 Columbus Blvd., Hartford,

Connecticut 06106

6875 Parkland Boulevard, Solon

Ohio 44139

Technical Data Sheet

Permatex



Windshield Repair

Kit

AAM Revised 05/08

NOT FOR PRODUCT SPECIFICATIONS.

THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.

PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.

PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)

PRODUCT DESCRIPTION

Permatex



Windshield Repair Kit makes repairs to most types

of damaged laminated windshield glass, including bullseye’s,

star damage in just a few minutes. This complete kit provides

everything needed for the repair. No mixing is required and it

cures by natural daylight.

PRODUCT BENEFITS

 Easy to use

 Everything required for repair is included

 Easy to follow instructions

 Fast curing

 Repairs bullseye’s, star damage and cracks

TYPICAL APPLICATIONS

 Repairs bullseye’s, star damage, small spider webs in

laminated automotive windshields

DIRECTIONS FOR USE

For Bullseye, Small Spider Web and Star Damage

Perform repairs in a shaded area with the windshield

temperatures between 50F and 75F. CAUTION: Do

not allow the resin in the syringe to come into contact

with the car’s finish as this may cause damage.

Clean out any loose glass particles from PIT (hole

caused by striking object) of the break using push pin

provided. Clean the area surrounding the break using

a dry cloth or paper towel.

Peel backing off one side of adhesive seal. Line up

hole in seal with PIT (tab pointing upward). Press seal

to glass. Run fingers around seal to insure a tight

bond.

Peel backing from TOP side of adhesive.

Line up the pedestal with the adhesive seal making

sure tabs match up. Press the pedestal to seal. Run

fingers around pedestal to insure a tight bond.

Cut tip off resin container (about 1/8 inch) to open

stem. Place stem 1/4 inch into pedestal opening.

Slowly squeeze resin tube, releasing resin into the

pedestal. Continue squeezing resin tube and remove

from pedestal. Wipe any excess resin from tip with

cloth and save empty container for Step 10.

Press fit injector into pedestal. Insure that the

connection is tight.

Hold injector in one hand, pull plunger upward with the

other hand. Lock plunger by ENGAGING LOWER

notch in plunger with spring clip. Release hands and

allow devise to remain in locked position. LET SIT

FOR 10 MINUTES then proceed to Step 8.

Remove injector form pedestal momentarily (to let air

in). Replace injector as in Step 6. DEPRESS plunger

downward and ENGAGE UPPER notch with spring clip.

LET SIT FOR A MINIMUM OF20 MINUTES then

proceed to Step 9.

Remove injector and discard. Loosen the outer edges

of pedestal with safety razor. Once top part of pedestal

and seal is bent away from the glass, grip the pedestal

tab and SLOWLY pull tab away. Wipe and remove

excess resin.

10.

Hold resin container in one hand and make ready the

clear yellow curing film in the other hand. Slowly

squeeze the resin container applying a drop of resin

into the PIT. Place the clear yellow curing film over the

PIT holding resin in the PIT.

11.

Run safety razor lightly over the clear yellow film to

vent out any air bubbles. NOTE: Ultra violet sun rays

cure the resin. Park vehicle in direct sunlight for 15

minutes. (On hazy days, park vehicle outside for a

minimum of 1 hour).

12.

Once resin has cured, carefully remove curing strip by

peeling it away from windshield.

FINISHING TIPS: If the surface of the glass is uneven,

the safety razor provided may be used to remove any

excess cured resin from windshield. Clean windshield

with glass cleaner or alcohol swab.

For Cleanup

1. Wipe up any excess resin with a clean cloth or paper

towel.

2. Cured resin must be scraped off windshield with safety

razor.

3. Clean hands with Fast Orange



hand cleaner.

PHYSICAL PROPERTIES

Typical Value

Chemical Type

Acrylic Resin

Appearance

Clear resin

Odor

Mild

Specific Gravity

1.02

Flash Point, TCC

>150F

GENERAL INFORMATION

This product is not recommended for use in pure oxygen

and/or oxygen rich systems and should not be selected

for use with chlorine or other strong oxidizing materials.

For safe handling information on this product, consult the

Material Safety Data Sheet, (MSDS).

ORDERING INFORMATION

Part Number

Container Size

09103

1 Complete Kit

Summary of content (2 pages)

PAGE 1
Toll Free: 87 PERMATEX (877-376-2839) 10 Columbus Blvd., Hartford, Connecticut 06106 6875 Parkland Boulevard, Solon Ohio 44139 Technical Data Sheet Permatex Windshield Repair Kit AAM Revised 05/08 PRODUCT DESCRIPTION Permatex Windshield Repair Kit makes repairs to most types of damaged laminated windshield glass, including bullseye’s, star damage in just a few minutes. This complete kit provides everything needed for the repair. No mixing is required and it cures by natural daylight.
PAGE 2
Technical Data Sheet Windshield Repair Kit STORAGE Products shall be ideally stored in a cool, dry location in unopened containers at a temperature between 8 and 28C (46 and 82F) unless otherwise labeled. Optimal storage is at the lower half of this temperature range. To prevent contamination of unused product, do not return any material to its original container. NOTE The data contained herein are furnished for information only and are believed to be reliable.