Specification Sheet

Toll Free: 87 PERMATEX
(877-376-2839)
10 Columbus Blvd., Hartford,
Connecticut 06106
6875 Parkland Boulevard, Solon
Ohio 44139
Technical Data Sheet
Permatex

Plastic Tank
Repair Kit
AAM Revised 10/02
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.
PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)
PRODUCT DESCRIPTION S.I.N.: 834-300
Permatex

Plastic Tank Repair Kit makes quick permanent
repairs to leaks in all types of plastic tanks (NOT for use on
plastic FUEL tanks). It repairs cracks up to 4” (10cm) long and
holes up to 3/8” (9mm) in diameter. Ideal for cars, trucks,
boats and RV’s.
PRODUCT BENEFITS
• Easy to use
• Everything required for repair is included
• Easy to follow instructions
• Fast curing
• Repairs can be made in 30 minutes
TYPICAL APPLICATIONS
• Windshield washer reservoirs
• Radiator overflow tanks
• Coolant reservoirs
• Water tanks
• Waste tanks
DIRECTIONS FOR USE
This product is NOT for use on plastic FUEL tanks. The repair
resin is designed to harden within 8 – 10 minutes and cures in
30 minutes. Read all directions before beginning repair.
Repairs can be made ideally at temperatures from 50°F to
75°F. Repairs made at lower temperatures will take longer to
cure.
1. Drain tank or reduce fluid level at least 2 inches below
damaged area.
2. Prepare damaged area by removing any oil, grease, tar
or dirt, etc. from the repair area. Sand the affected area
to at least 1 inch beyond the damage.
3. For cracks that may continue to expand, drill a small hole
at each end of the crack
4. Clean the area with alcohol swab. Cut the fiberglass
cloth to fit within the sanded area.
5. The resin must be mixed and applied in less than 8
minutes as the resin will begin to harden. Mix the resin
as follows: Burst the seam that separates the two
materials by applying pressure to one side. Knead the
contents of the pouch back and forth until the mixture is
of uniform color (mix for 2 minutes maximum).
6. Cut off the top of the pouch and dispense some of the
resin mixture onto the damaged area. Spread the resin
mixture in a uniform layer with the supplied brush onto
the area to be covered by the fiberglass. (Note: The
material will become warm to the touch.)
7. Place the fiberglass over the resin covered area. Spread
the remaining mixture over the fiberglass until it is
completely saturated. Taper the areas of the repair
beyond the fiberglass. Smooth the repaired area with the
brush.
Repair will be complete when the resin cures in 30
minutes. Tank may be refilled after 30 minutes or when
the repair is tack free.
For Cleanup
1. Wipe off any uncured resin with a cloth.
2. Uncured resin may be cleaned up with a cloth saturated
with alcohol.
3. Cured resin will have to be scraped off or chipped off.
4. Clean hands with alcohol for uncured resin. Cured resin
on hands will wear off.
5.
Clean hands with Fast Orange

hand cleaner provided.
PHYSICAL PROPERTIES
Typical Value
Chemical Type Epoxy Resin
Appearance Black/Clear Viscous Liquid
Odor Mild/Mercaptan
Specific Gravity 1.15
Flash Point, COC >200°F
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected
for use with chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
ORDERING INFORMATION
Part Number Container Size
09100 1 Complete Kit
STORAGE
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8°
to 28°C
(46°
to 82°F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent
contamination of unused product, do not return any material to
its original container.