Specification Sheet

Toll Free: 87 PERMATEX
(877-376-2839)
10 Columbus Blvd., Hartford,
Connecticut 06106
6875 Parkland Boulevard, Solon
Ohio 44139
Technical Data Sheet
Permatex



the Right Stuff

 Grey
AAM Revised 10/07
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.
PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)
PRODUCT DESCRIPTION
PERMATEX
®
The Right Stuff Grey is a single component,
room temperature curing, elastomeric gasketing compound
designed to provide reliable “formed-in-place” gaskets for
mechanical assemblies. The Right Stuff Grey has been
specifically designed to perform under higher torque loads of
engines with high bolt densities, typically import vehicles. This
product has a high blowout resistance, allowing leakproof
gaskets to be made and placed into service immediately after
reassembly. Permatex

Right Stuff Grey is sensor safe and
seals instantly forming reliable, long lasting elastomeric rubber
gaskets that outperform precut gaskets. OEM specified by
Nissan, Honda, Mazda and Kia.
PRODUCT BENEFITS
• Immediate sealability
• Instant blow-out resistance
• Import OEM Approved and Specified
• Replaces most cut gaskets
• Low odor
• Resistant to ATF/oil/coolant
• Consistent sealing
• Sensor safe
TYPICAL APPLICATIONS
• Timing gear covers
• Transmission pans
• Valve covers
• Oil pans
• Water pumps
• Gearboxes
• Intake manifold end seals
• Stamped sheet metal covers
• Compressors
• Gearboxes
PROPERTIES OF UNCURED MATERIAL
Typical Value
Chemical Type Elastomeric Rubber
Appearance Metallic Grey
Specific Gravity @ 20°C
1.45
Viscosity Thixotropic Paste
Flash Point (TCC), °F
>200
DIRECTIONS FOR USE
For assembly as form-in-place gasket
1. Remove all previous material from mating surfaces.
Permatex

Gasket Remover is recommended for most
materials (not for plastics or painted surfaces).
2. For best results, clean and dry all surfaces with a
residue-free solvent, such as Permatex

Brake and
Parts Cleaner.
3. Cut nozzle to desired bead size, 1/16“ to 1/4“ in
diameter. An 1/8” bead is usually sufficient for most
applications.
4. Remove cap, puncture tube or cartridge seal and attach
extension nozzle.
5. Apply a continuous and even bead of The Right Stuff™
for Imports to one surface, first tracing the internal areas
of the gasket configuration, then all surrounding bolt
holes as shown below:
6. Assemble parts within 5 minutes while The Right Stuff™
for Imports is still wet. Secure or tighten to
recommended torque specs.
7. Re-torque will not be necessary after the product has
cured.
For PowerBead
1. Clean and dry all flange surfaces to be sealed.
2. Remove black cap from top of extension nozzle.
3.
Turn nozzle extension one complete turn (360°)
counterclockwise.
4. Depress finger trigger and apply a continuous 1/16 inch
to 1/8 inch PowerBead to one surface.
5.
Assemble parts within 5 minutes while The Right Stuff

Grey is still wet. Secure or tighten to recommended
torque specs.
6. Parts or vehicle may be placed back into service
immediately.
7. Re-torque will not be necessary after the product has
cured.
8. To close, turn extension nozzle clockwise until tight
(about one full turn). Wipe off excess material from
nozzle and replace black cap.
For Cleanup
1. Allow excess material to extend beyond the extension
nozzle or aerosol tip to cure, sealing and protecting the
remaining product from moisture. For reuse, simply