SDS

ManualsBrandsPermatex ManualsAutomotive5 Minute Plastic Welder Epoxy - 0.84 oz.

Material Safety Data Sheet

1. PRODUCT IDENTIFICATION

Product Name: 84115 5 MINUTE PLASTIC WELD (ACTIVATOR)

Item No: PTX203012B

Product Type: Activator

2. COMPOSITION/INFORMATION ON INGREDIENTS

Component: Weight% ACGIH; TLV-TWA OSHA PEL

METHYL METHACRYLATE

80-62-6

60-80 50 ppm 100 ppm; 410 mg/m

ACRYLONITRILE-BUTADIENE

POLYMER

9003-18-3

1-10 Not listed Not listed

3,5-DIETHYL-1,2-DIHYDRO-1-

PHENYL-2-PROPYLPYRIDINE

34562-31-7

1-10 Not listed Not listed

3. HAZARDS IDENTIFICATION

Toxicity:

May cause eye and skin irritation. May cause skin sensitization. Exposure to vapors or mist may result in

irritation of the respiratory tract.

Primary Routes of Entry:

Eye and skin contact, ingestion, inhalation

Signs and Symptoms of Exposure:

Eyes: Exposure to liquid or vapor causes moderate eye irritation. Symptoms may include burning, tearing,

redness, stinging, blurred vision and corneal injury. Repeated skin contact may cause allergic skin

reactions. Excessive accidental exposure may cause headache, dizziness, nausea and mild respiratory

irritation. Moderately toxic if swallowed. Irritating to mouth, throat and stomach with nausea.

Component: Weight% NTP ACGIH Carcinogens IARC Carcinogen

METHYL METHACRYLATE

80-62-6

60-80 male rat-no evidence;

female rat-no

evidence; male mice-

no evidence; female

mice-no evidence

A4 - Not Classifiable

as a Human

Carcinogen

Group 3: Monograph 60, 1994

Aggravated Medical Condition:

Preexisting eye, skin and respiratory disorders may be aggravated by overexposure to this product.

4. FIRST AID MEASURES

Ingestion:

If swallowed, do not induce vomiting - seek medical advice. Never give anything by mouth to an

unconscious person.

Inhalation:

Move to fresh air in case of accidental inhalation of vapors. Obtain medical attention.

Skin Contact:

Remove contaminated clothing. Wash area with soap and water. If irritation persists, seek medical

attention

Eye Contact:

In case of contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical

attention if irritation persists

5. FIRE FIGHTING MEASURES

Flash Point °F(C°):

52.7°F (11.5°C)

Recommended Extinguishing Media:

Carbon dioxide, Dry chemical, Foam

Special Fire-Fighting Procedures:

Firefighters shoud wear self-contained breathing apparatus and protective

clothing to prevent all skin and eye contact

Hazardous Products of Combustion:

Oxides of carbon, Oxides of nitrogen

Unusual Fire/Explosion Hazards:

Flammable. Closed containers may rupture or explode when exposed to

extreme heat.

Lower Explosive Limit:

1.6%

Upper Explosive Limit:

12.5%

1 of 3

ITW Permatex

10 Columbus Blvd.

Hartford, CT 06106 USA

Telephone: 1-87-Permatex

(877) 376-2839

Emergency: 800-255-3924 (ChemTel)

International Emergency: 00+ 1+ 813-248-0585

Summary of content (6 pages)

PAGE 1
ITW Permatex 10 Columbus Blvd. Hartford, CT 06106 USA Telephone: 1-87-Permatex (877) 376-2839 Emergency: 800-255-3924 (ChemTel) International Emergency: 00+ 1+ 813-248-0585 Material Safety Data Sheet 1. PRODUCT IDENTIFICATION Product Name: Item No: Product Type: 84115 5 MINUTE PLASTIC WELD (ACTIVATOR) PTX203012B Activator 2.
PAGE 2
Product Name: 84115 5 MINUTE PLASTIC WELD (ACTIVATOR) Item No. PTX203012B 6. ACCIDENTAL RELEASE MEASURES Spill Procedures: Eliminate all sources of ignition. Maintain good ventilation. Take up with an inert absorbent. Store in a closed waste container until disposal. Prevent from entering waterways or sewers. 7. HANDLING AND STORAGE Storage: Handling: Store away from heat, sparks or open flame. Do not store at temperatures above 100°F (38°C). Do not use near heat, sparks or open flame.
PAGE 3
Product Name: 84115 5 MINUTE PLASTIC WELD (ACTIVATOR) Item No. PTX203012B Class 3, PG II UN 1133 Hazard Class: UN Number: SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313 Toxic Chemical. Methyl methacrylate California Proposition 65: No California Prop 65 chemicals are known to be present. TSCA Inventory Status: All components of this product are listed (or exempt) on the EPA TSCA inventory. 16. OTHER INFORMATION HEALTH 2, FLAMMABILITY 3 , REACTIVITY 2.
PAGE 4
ITW Permatex 10 Columbus Blvd. Hartford, CT 06106 USA Telephone: 1-87-Permatex (877) 376-2839 Emergency: 800-255-3924 (ChemTel) International Emergency: 00+ 1+ 813-248-0585 Material Safety Data Sheet 1. PRODUCT IDENTIFICATION Product Name: Item No: Product Type: 84115 5 MINUTE PLASTIC WELD (ADHESIVE) R478ADH2 Adhesive 2.
PAGE 5
Product Name: 84115 5 MINUTE PLASTIC WELD (ADHESIVE) Item No. R478ADH2 4. FIRST AID MEASURES Inhalation: Skin Contact: Eye Contact: Move to fresh air in case of accidental inhalation of vapours. Obtain medical attention. Remove contaminated clothing. Wash area with soap and water. If irritation persists, seek medical attention In case of contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical attention if irritation persists 5. FIRE FIGHTING MEASURES 52.7°F (11.
PAGE 6
Product Name: 84115 5 MINUTE PLASTIC WELD (ADHESIVE) Item No. R478ADH2 13. DISPOSAL CONSIDERATIONS Recommended Method of Disposal: Disposal should be made in accordance with federal, state and local regulations D001 as per 40CFR 261.21 US EPA Waste Number: 14. TRANSPORTATION INFORMATION DOT (49CFR 172) U.S.