User Guide

Toll Free: 87 PERMATEX
(877-376-2839)
10 Columbus Blvd., Hartford,
Connecticut 06106
6875 Parkland Boulevard, Solon
Ohio 44139
Technical Data Sheet
Permatex

PermaPoxy Multi-
Metal Epoxy Products
AAM Revised 07/02
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.
PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)
PRODUCT DESCRIPTION S.I.N.: 834-300
Permatex

PermaPoxy Multi-Metal products are two part,
filled epoxy adhesive systems. PermaPoxy Multi-Metal
epoxies are of a maximum strength formula that is available in
several working times. PermaPoxy Multi-Metal Epoxies are
ideal for complex, multi-piece assemblies. They are water and
solvent resistant and available in dual syringes or tubes.
PRODUCT BENEFITS
• Will not shrink
• Various curing cycles
• No clamping needed
• Fills gaps
• Dark grey color
• Impact resistant
• Water resistant
• High temperature resistant
TYPICAL APPLICATIONS
• Aluminum
• Brass
• Chrome
• Copper
• Iron
• Stainless Steel
• Steel
• Cast
DIRECTIONS FOR USE
1. Protect work area from accidental spills.
2. Surface must be clean, dry and free of grease & oil.
3. Roughen surfaces with sandpaper or other abrasives.
4. Use a sharp blade to cut off the tips of both nozzles.
5. Depress plunger on syringe or squeeze out of tubes
equal amounts of resin and hardener. Thoroughly mix
resin and hardener on a clean discardable surface for at
least one (1) minute or until uniform in color.
6. Apply to surfaces being repaired. Assemble parts
immediately. Remove excess epoxy immediately.
7. Allow bond to set for the fixture time before moving.
For Cleanup
1. For any cleanup, use isopropyl alcohol before the
material is allowed to dry.
2. Clean hands with Permatex

Fast Orange
®
hand cleaner
or soap and water.
PROPERTIES OF UNCURED MATERIAL
Typical Value
Chemical Type
Mix Ratio
Epoxy and Mercaptan or Amine
Resins
1:1
Appearance
Resin
Hardener
Black
Off white/White
Odor Mild
Specific Gravity 1.75 - 1.85
Flash Point, TCC >300ºF
Viscosity Paste
CURING PROPERTIES
Working Time Fixture Time
84109 4 – 5 minutes 8 – 10 minutes
84112 90 minutes 90-110 minutes
84209 4 – 5 minutes 8 – 10 minutes
84212 90 minutes 90-110 minutes
Final color Grey
Temperature range -60°F to +300°F(Continuous)
+350°F(Intermittent)
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
an adhesive for chlorine or other strong oxidizing
materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
ORDERING INFORMATION
Part Number Container Size
84109 4 min. Multi-Metal Epoxy,
0.84 fl. oz. dual syringe, carded
84112 90 min. Multi-Metal Epoxy,
0.84 fl. oz. dual syringe, carded
84209 4 min. Multi-Metal Epoxy,
2 – 1oz. tubes, carded
84212 90 min. Multi-Metal Epoxy,
2 – 1oz. tubes, carded
STORAGE
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8°
to 28°C
(46°
to 82°F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent
contamination of unused product, do not return any material to
its original container.