Specification Sheet
Toll Free: 87 PERMATEX
(877-376-2839)
10 Columbus Blvd., Hartford,
Connecticut 06106
6875 Parkland Boulevard, Solon
Ohio 44139
Technical Data Sheet
Permatex
Aerosol Rust
Treatment
AAM Revised 05/07
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.
PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)
Permatex is a trademark of Illinois Tool Works, Inc. 2007 ITW Permatex, Inc. All rights reserved.
PRODUCT DESCRIPTION S.I.N.: 834-300
Permatex
Aerosol Rust Treatment is a fast drying, vinyl
coating that sprays on clear and converts rust to a black
metal-protective coating that prevents continued corrosion.
The product protects the surface as a pre-primer.
PRODUCT BENEFITS
Neutralizes rust and prevents additional rust
Converts and primes in one operation
Eliminates sandblasting
Works on damp, rusty metal
TYPICAL APPLICATIONS
AAM
Under hood applications
Wheel wells
DIRECTIONS FOR USE
NOTE: This product is not recommended for use under
exterior automotive sheet metal finishes. May cause
blistering or peeling.
1.
Provide adequate ventilation.
2.
For best results, apply to clean, dry surfaces. Remove
loose rust with a wire brush. Surface rust must be
present.
3.
Shake can well. Note: The product does not require a
ball agitator. For best results, the aerosol can should be
at room temperature before spraying.
4.
Holding can 8 to 10 inches from the surface, press the
nozzle and uniformly discharge the product to the
corroded area. A black coating will appear in about 5
minutes. Uneven color indicates need for additional
coats. Apply second coat within 2 minutes.
5.
NOTE: After complete drying, Permatex Aerosol Rust
Treatment must be topcoated for maximum durability.
Allow 24 hours minimum to dry before applying a finish
paint. Water based finish topcoat paints will require an
additional non-water based primer prior to application of
topcoat.
Note: Aerosol product (3 coats) will cover 10 to 12 square
feet at 2 mil DFT.
For Cleanup
1.
Turn can upside-down and spray to clear nozzle.
2.
Clean hands with Permatex
brand hand cleaners.
PROPERTIES OF MATERIAL
Typical Value
Chemical Type
Vinyl butyral
Appearance
Clear liquid
Odor
Pungent
Flash Point
Aerosol, contents under pressure,
consult MSDS
NFPA 704 Flammability Rating
3 (Flammable)
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
ORDERING INFORMATION
Part Number
Container Size
81849 (79DA)
16 oz. aerosol can
STORAGE
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8 and 28C
(46 and 82F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range.
NOTE
The data contained herein are furnished for information only
and are believed to be reliable. We cannot assume
responsibility for the results obtained by others over whose
methods we have no control. ITW Permatex, Inc.
specifically disclaims all warranties expressed or implied,
including warranties of merchantability or fitness for a
particular purpose, arising from sale or use of Permatex,
Inc. products and disclaims any liability for consequential
or incidental damages of any kind, including lost profits.
This product may be covered by one or more United States or
foreign patents or patent applications.