Specification Sheet

Toll Free: 87 PERMATEX
(877-376-2839)
10 Columbus Blvd., Hartford,
Connecticut 06106
6875 Parkland Boulevard, Solon
Ohio 44139
Technical Data Sheet
Permatex



Rearview Mirror
Adhesive
AAM Revised 02/09
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.
PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)
Permatex and Fast Orange are trademarks of Illinois Tool Works, Inc.

2009 Permatex, Inc. All rights reserved.
PRODUCT DESCRIPTION
Permatex

Rearview Mirror Adhesive is a two part adhesive
that permanently bonds mirror buttons to windshields.
Achieves handling strength in seconds, and mirror mounting
strength in 30 minutes. ODC free. OEM approved. NOT
designed for PLASTIC buttons.
PRODUCT BENEFITS
• Easy to use
• Fast curing
• OEM factory service specified
TYPICAL APPLICATIONS
• All foreign and domestic metal rearview mirror mounting
buttons
DIRECTIONS FOR USE
Read all directions before beginning repair. Repairs can be
made ideally at temperatures from 50°F to 75°F. Repairs
made at lower temperatures will take longer to cure.
1. Remove the mounting button from the mirror bracket.
2. On the outside of the windshield, mark the spot where
the button was mounted with a felt-tip marker or
crayon.
3. Scrape all old adhesive off windshield and the button
with a safety razor. (Be careful not to gouge button
with razor.)
4. Using fine grit sandpaper, put on a flat, hard surface
and gently sand the mounting surface of the button
using a circular motion.
5. Open the Cleaner/Activator towelette by pulling both
sides of the protective packet at a point at the top sides
of the package. Fold the packet back to use. The
towelette is attached to the foil packet. Do Not
Remove.
6. Apply the activator to the inside of the windshield where
the spot has been marked by the felt-tip marker. Use a
circular motion and make sure that the activator
overlaps the mark by at least ½ inch. Allow the
activator to dry for at least 2 minutes. DO NOT
TOUCH the glass after the activator has been applied.
7. Tear open the adhesive pouch at the top or use
scissors to cut open. Apply one drop only to the
center of the button. (Remember, more is not better.)
8. Immediately apply the button to the windshield,
ensuring that the correct side is up (usually the rounded
side). Hold firmly against the windshield for at least 1
minute. Do not move the button during this time. Allow
to set for at least 30 minutes.
9. Mount the mirror bracket onto the button. Clean off the
marking on the outside of the windshield with alcohol.
10. Wipe off any uncured resin with a cloth.
11. Uncured resin may be cleaned up with a cloth
saturated with alcohol.
12.
Clean hands with Fast Orange

hand cleaner.
PHYSICAL PROPERTIES
Typical Value
Chemical Type Methacrylate Ester
Appearance Adhesive-yellow/Activator-
blue-green
Odor Mild
Specific Gravity 1.13
Flash Point, COC
>200°F
Temperature range
-60°F to 200°F
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
an adhesive for chlorine or other strong oxidizing
materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
ORDERING INFORMATION
Part Number Container Size
81844(11067-2) 2-part, carded
STORAGE
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8° and 28°C
(46° and 82°F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent
contamination of unused product, do not return any material to
its original container.
NOTE
The data contained herein are furnished for information only
and are believed to be reliable. We cannot assume
responsibility for the results obtained by others over whose
methods we have no control. Permatex, Inc. specifically
disclaims all warranties expressed or implied, including
warranties of merchantability or fitness for a particular
purpose, arising from sale or use of Permatex, Inc.
products and disclaims any liability for consequential or
incidental damages of any kind, including lost profits.
This product may be covered by one or more United States or
foreign patents or patent applications.