Specification Sheet

Technical Data Sheet Penetrating Grade Threadlocker Green
Permatex is a trademark of Permatex, Inc. © 2004 All rights reserved
For Reassembly
1.
Remove loose product from nut and bolt.
2.
Apply primer to all threads, regardless of metal type.
3.
Assemble and tighten as usual.
PROPERTIES OF UNCURED MATERIAL
Typical Value
Chemical Type
Anaerobic Dimethacrylate Ester
Appearance
Green Fluorescent Liquid
Specific Gravity
1.08
Viscosity @ 25
°
C, mPa.s (cP)
9 to 16
Brookfield RVF, spindle
#3, Helipath @ 20 RPM
Flash Point (TCC),
°
C (
°
F)
>93 (>200)
TYPICAL CURING PERFORMANCE
Cure speed vs. substrate
The rate of cure will depend on the material used. Permatex

Penetrating Grade Threadlocker Green will react faster and
stronger with Active Metals. However, Inactive Metals will
require the use of a primer (Surface Prep) to obtain maximum
strength and cure speed at room temperature.
Active Metals
Inactive Metals
Soft Steel Iron
Bright Platings
Copper
Anodized Surfaces
Brass
Titanium
Manganese
Zinc
Bronze
Pure Aluminum
Nickel
Stainless Steel
Aluminum Alloy
Cadmium
Cure speed vs. temperature
The rate of cure will depend on the ambient temperature. Full
cure is attainable in 24 hours at room temperature, 22°C
(72°F), or 1 hour at 93°C (200°F).
Cure speed vs. primer
To shorten cure time or if an inactive surface is present,
applying a primer (Surface Prep) to the surface will improve
cure speed. A 3/8-16 steel nut and bolt assembly will fixture in
3 minutes using a primer, while fixturing will occur in 20
minutes without a primer. Full cure in 24 hours for both
procedures.
PERFORMANCE OF CURED MATERIAL
(After 24 hr at 72
°
F on 3/8-16 steel Grade 8 Nuts and Grade 5 bolts)
Typical
Value
Range
Breakaway Torque, Nm,
10
3 to 17
(in.lbs)
(85)
(20 to 150)
Prevail Torque, Nm
29
17 to 41
(in.lbs)
(250)
(150 to 350)
Where Breakaway Torque is the force required to initiate the fastener
movement and Prevail Torque is the force required to disassemble the
fastener once Breakaway Torque has occurred.
TYPICAL ENVIRONMENTAL RESISTANCE
Temperature Resistance
Product temperature range from -175°C to 150°C (-65°F to
300°F). The Breakaway and Prevailing Torque values
decrease as temperature increases, however the assembly
remains effective against vibration and leakage.
Chemical / Solvent Resistance
The product retains effective properties in contact with
automotive fluids, such as motor oil, gasoline, brake fluids,
transmission fluids, alcohol and antifreeze solutions.
GENERAL INFORMATION
This product is not recommended for use in pure oxygen
and/or oxygen rich systems and should not be selected as
a sealant for chlorine or other strong oxidizing materials.
For safe handling information on this product, consult the
Material Safety Data Sheet, (MSDS).
This product is not normally recommended for use on plastics
(particularly thermoplastic materials where stress cracking of
the plastic could result). It is recommended to confirm
compatibility of the product with such substrates.
ORDERING INFORMATION
Part Number
Container Size
29000
6 ml tube, carded
29040
36 ml bottle, carded
OEM Interchange
Manufacture
OEM Specifications Numbers
Auto Latina
ESEM4G203A
Ford
SSM-4G-9520-A
WSK-M2G351-
A1
ESF-M2G132-A
GM
998 5306
Isuzu
1-8844-6375-0
Maxiun
0710109
Scania
814281
Valmet
078723020
Volvo
591264
STORAGE
Products shall be ideally stored in a cool, dry location in
unopened containers at a temperature between 8
°
to 28
°
C
(46
°
to 82
°
F) unless otherwise labeled. Optimal storage is at
the lower half of this temperature range. To prevent
contamination of unused product, do not return any material to
its original container.
NOTE
The data contained herein are furnished for information only
and are believed to be reliable. We cannot assume
responsibility for the results obtained by others over whose
methods we have no control. Permatex, Inc. specifically
disclaims all warranties expressed or implied, including
warranties of merchantability or fitness for a particular
purpose, arising from sale or use of Permatex Inc.
products and disclaims any liability for consequential or
incidental damages of any kind, including lost profits.
This product may be covered by one or more United States or
foreign patents or patent applications.