Specification Sheet
Toll Free: 87 PERMATEX
(877-376-2839)
10 Columbus Blvd., Hartford,
Connecticut 06106
6875 Parkland Boulevard, Solon
Ohio 44139
Technical Data Sheet
Permatex
®
Medium Strength
Threadlocker BLUE Gel
AAM Revised 01/08
NOT FOR PRODUCT SPECIFICATIONS.
THE TECHNICAL DATA CONTAINED HEREIN ARE INTENDED AS REFERENCE ONLY.
PLEASE CONTACT PERMATEX, INC., TECHNICAL SERVICE DEPARTMENT FOR ASSISTANCE AND RECOMMENDATIONS FOR YOUR SPECIFIC APPLICATION.
PERMATEX, INC., HARTFORD SQUARE NORTH, 10 COLUMBUS BOULEVARD, HARTFORD, CT 06106 PHONE – (1-87PERMATEX)
PRODUCT DESCRIPTION
PERMATEX
Medium Strength Threadlocker BLUE Gel is a
medium strength anaerobic threadlocking gel conveniently
packaged in a new Gel Twist or Gel Squeeze applicator.
The product, like its liquid counterpart, is a single component,
anaerobic gel that cures when confined in the absence of air
between close fitting metal surfaces, ideal for all 6mm to
25mm (1/4 inch to 1 inch) diameter threaded assemblies.
Excellent chemical resistance and temperature resistance
range of -65°F to +300°F (-54°C to +149°C). The assembly is
easily removable with hand tools for servicing requirements.
NSF Nonfood Components Program Listed (P1) (135871).
PRODUCT BENEFITS
Improved Reliability
• Eliminates vibration issues
• Seals against leakage
• Prevents rusting of threads
• Designed for use on vertical or hard-to-reach applications
• Cures without cracking or shrinking
• Adjusts or disassembles with hand tools
Easy Application
• No mess Gel Twist or Gel Squeeze applicator
• Gel-type product does not drip when applied
• Single component
• No curing outside of joint
• Thixotropic: resists dripping from threads during assembly
• No torque compensation required during assembly
TYPICAL APPLICATIONS
Prevents loosening and leakage of threaded fasteners.
Particularly suitable for applications such as:
• Belt tensioner bolts
• Pulley bolts
• Cup and core plugs
• Fan hub bolts
• Visor mount bolts
• Starter mounting bolts
• Alternator Mounting Bolts
• Intake Manifold Bolts
• Valve Cover Bolts
• Vacuum Adjustment Screws
• Oil Pan Bolts
• Axle Cover Screws
• Drive Shaft Bolts
• Disc Brake Caliper Bolts
• Gearshift Knobs
DIRECTIONS FOR USE
For assembly
1.
Clean all threads (bolt and hole) with a cleaning solvent
such as Permatex
Brake and Parts Cleaner and allow to
dry.
2.
Remove the translucent protective cap by pulling off at an
angle.
3.
For Gel Twist turn the dial on the bottom of the container
until 1/8” to 1/4" (3mm to 6mm) of material protrudes from
the top of the application tip. Note: First time use may
require 4 to 5 full turns of the dial before material appears in
the tip.
For Gel Squeeze, remove cap and squeeze 1/8 to 1/4"
(3mm to 6mm) of material beyond tip.
4.
Apply threadlocker to the engagement area of the male
fitting (usually the leading 5 to 6 threads).
5.
Assemble parts and tighten to recommended torque.
6.
If unused gel contacts metal threads, do not retract
threadlocker back into the tube. Wipe off with a clean towel.
7.
Replace protective cap.
For Cleanup
1.
Residual liquid films and/or fillets outside the joint are
readily soluble in Permatex
Brake and Parts Cleaner.
2.
Cured product can be removed with a combination of
soaking in Permatex
Gasket Remover and mechanical
abrasion such as a wire brush.
For Disassembly
1.
Remove with standard hand tools.
2.
In the rare instance where hand tools do not work, because
of excessive engagement length, apply localized heat to nut
or bolt to approximately 450°F (232° C). Disassemble while
hot.
For Reassembly
1.
Remove loose product from nut and bolt following cleanup
procedure above.
2.
Apply Surface Prep activator to all threads, regardless of
metal type and allow to dry.
3.
Apply threadlocker gel as above.
4.
Assemble and tighten as usual.
PROPERTIES OF UNCURED MATERIAL
Typical Value
Chemical Type
Anaerobic Dimethacrylate Ester
Appearance
Opaque Blue Fluorescent Gel
Specific Gravity
1.15
Viscosity @ 25
°
C, cP
Brookfield RVF, spindle
#3, @ 20 RPM
Gel
Flash Point (TCC),
°
F (
°
C)
>200 (>93)