INSTRUCTION MANUAL Model No: PH-90204-BK 110-120V 1500W Ques Concerns, Missing Before returning to the store, please contact our customer service team Please call 888-287-0735 / 8am – 5pm PST / Monday to Friday Email: Service@Permasteel.
ASSEMBLY & OPERATION INSTRUCTION Please read carefully and Save this instruction for future reference Introduction The infrared heater contains a gold halogen lamp formed reflector heating system that provides even heat distribution. The infrared heater saves 30%-40% of electricity in comparison to traditional heaters. The infrared heater is commonly used for indoor or outdoor spot heating. Perfect for garages, outdoor patios, indoor pools or workshops.
13. Do not put fingers or foreign objects into the heater element while in operation. 14. Do not leave the appliance unattended when not in use. 15. This heater is not intended for use in bathrooms, laundry room and similar indoor locations. Never use the heater where it may fall into a bathtub or other water container. 16. No liability can be accepted for any damage caused by none compliance with these instructions or any other improper use or mishandling. 17.
WARNING: NEVER place hands under the heating elements. Introduction The PH-90204-BK halogen heater produces instant and comfortable heat like the sun. These robust and weatherproof heaters are designed for domestic and commercial heating applications within outdoor areas. It is intended for outdoor use only. Model PH-90204-BK Voltage(V) 110-120V AC Wattage(W) 1500W Hertz (Hz) 60 Dimensions W×H×D(mm) 67.5*10.5*7.2cm Weight (KG) 2.
ASSEMBLY INSTRUCTIONS Installation Hardware: A Bracket L Shape 4PCS - 4PCS C Mounting Screw PA5mm*25mm 4PCS D Bolts M5mm*10mm 4PCS E Nuts M6mm 2PCS M6mm*12mm 2PCS B Plastic Anchor F Hex Bolts
INSTALLATION INSTRUCTIONS Tools Needed: • Pencil • Hammer • Level • Screw-Driver • Power Drill • Drill Bits A wall mounting bracket & hardware is provide with the heater which has been specifically designed to allow this product to be Mounted to a wall or ceiling. Before drilling holes on the wall/ceiling, make sure the wall is a solid structure and that there are no hidden water pipes or electric wires.
1. Attach 2pcs (A) L brackets to heater unit with 4pcs (D) M5mm*10mm Bolts (see Figure A). A 2. Drill 5/16” diameter holes on wall or celling. (see Figure B) For best results, attach directly on wall studs if possible. 5/16” diameter Anchor holes 1” 3-3/8” – 3-1/2” 1” B 3. Holes for anchors should be drilled 1 inch apart for each bracket, use bracket as template. The distance between left & right brackets should be 3-3/8 to 3-1/2 inches center to center of inner holes of brackets.
4. Insert 4pcs (B) wall anchors into drilled holes on wall (see Figure C). 3-3/8” 1” C 5. Mount the 2pcs (A) brackets using 4pcs (C) PA5mm*25mm mounting screws making sure they are snug and level (see Figure D).
6. Attach heater unit to wall brackets (Note: two people are needed for this step) while one person holds & aligns the heater unit to mounting brackets, the 2nd person should use the two (E) nuts M6mm and two (F) M6mm* 12mm Hex Bolts to attach to wall brackets. Please install the bolts from the inside and tighten the bolt nuts from the outside to secure the brackets and adjust brackets if necessary. (see Figure E).
INSTALLATION WITH TRIPOD STAND Accessories for tripod stand mounting. • • • 4pcs M5mm*10mm bolts 2pcs L shaped brackets 1 hand bolt & 1 hand nut 1. Attach 2pcs (A) L brackets to heater unit with 4pcs (D) M5mm*10mm Bolts (see Fig. A) A 2. Make sure plastic spacers are attached to tripod post (see Fig.
3. With the help of another person, attach the heater assembly to the tripod stand using the hand-bolt & hand-nut, screw tightly.
REMOTE CONTROL INSTRUCTION OPERATING Product Key Function: 1. Turn ON/OFF the power 2.
CLEANING AND MAINTENANCE Regular and careful cleaning helps your infrared heater to operate efficiently for many trouble-free years. To clean your heater, please follow the steps below: 1. Unplug the power cord for your safety before cleaning your heater. 2. Make sure the heater is cool before continuing 3. To keep the heater clean, the outer should be cleaned with a soft, damp cloth. You may use a mild detergent if necessary. After cleaning, dry the unit with a soft cloth.
Limited Warranty: This Patio Heater is Warranted to be free of defects in materials or workmanship for a period of 90 days from the date of the original purchase. Vendor may require reasonable proof of date of purchase therefore you should retain your sales receipt or invoice. This limited warranty does not cover failure due to abuse, misuse, accidents or unauthorized alterations or repairs.
