Installation & Operation Manual Commercial Back Bar Sliding Door SDB & SDP Series Model SDBR48 Shown Form No.
Models SDB/SDP Installation & Operation Manual Table of Contents General Information.................................................................................................................................. 2 Safety....................................................................................................................................................... 2 Prior To Installation..............................................................................................................
Models SDB/SDP Installation & Operation Manual Prior To Installation Uncrating and Inspection The drain tube must be placed over a floor drain or into a condensate management system such as a “Condensate Evapaway’ pan and heater. Remove all crating material. Carefully inspect cabinet for hidden damage. If damage is discovered, file your claim immediately with the transport company. Perlick is not responsible for damage in transit.
Models SDB/SDP Installation & Operation Manual Installation General Information Installing the Unit • If unit has been laid on its back or sides, place unit upright and allow minimum of 24 hours before connecting power. • For units equipped with a power cord, the cord and plug may be aligned with a recess in the back panel to allow the unit to be pushed closer to the wall. For correct alignment, the wall outlet must be located 4” - 10” above the floor. CAUTION 1.
Models SDB/SDP Installation & Operation Manual Sealing Cabinet to Floor Cabinet For units without casters or legs, it may be necessary to seal the base of the cabinet to the floor. This can be accomplished by laying a bead of silicone sealant between the base of the cabinet and the floor (Figure 1). Bead Silicon Sealer (RTV) Floor Figure 1.
Models SDB/SDP Installation & Operation Manual Adjustments Never attempt to repair or perform maintenance on the unit until the main electrical power to the unit has been disconnected! 5. Plug new LED into harness and secure to housing using screws removed in step 2. DANGER 6. Snap LED cover into place. Sliding Doors Shelving Adjustment CAUTION Removing / Installing Completely empty shelf or drawer before removing. 1.
Models SDB/SDP Installation & Operation Manual Maintenance Stainless Steel Care & Cleaning parallel to the lines. When the grain cannot be seen, play it safe and do not use a circular motion. Polish in a consistent straight pattern. General Contrary to popular belief, stainless steel is susceptible to rusting. Corrosion on metals is everywhere. It is recognized quickly on iron and steel as unsightly yellow/orange rust.
Models SDB/SDP Installation & Operation Manual Cleaning the Condenser Av o i d d a m a g i n g o r crushing the condenser fins or tubing. Failure to follow this procedure may damage the compressor and void the warranty. CAUTION The condenser (located behind front grille cover) should be cleaned every three (3) months. Use a soft bristle brush and vacuum to remove the dust and lint. Recommended Cleaners for Specific Situations Job Cleaning Agent Comments Routine cleaning.
Models SDB/SDP Installation & Operation Manual Troubleshooting Before Calling For Service If the unit appears to be malfunctioning, read through the Operation section in this manual first. If the problem persists, check through this troubleshooting section. Locate the problem and refer to the cause and remedy before calling for service. The problem could be something that can be solved without a service call.
Models SDB/SDP Installation & Operation Manual Problem Cause Solution System runs for long period of time. Condenser dirty or obstructed. Door kept open for long time or opened more frequently. Warm product place in cabinet recently. Hot day and warm room temperature. Clean condenser and clear obstruction. Wait 24 hours and recheck temperature. Reset preset temperature if necessary. Normal for system to run more frequently. Condensation forms inside the compartments.
Models SDB/SDP Installation & Operation Manual Dimensions Printed in USA 11 0213
Models SDB/SDP Installation & Operation Manual Printed in USA 12 0213
Models SDB/SDP Installation & Operation Manual Printed in USA 13 0213
Models SDB/SDP Installation & Operation Manual Printed in USA 14 0213
Models SDB/SDP Installation & Operation Manual Wiring Diagrams Printed in USA 15 0213
Models SDB/SDP Installation & Operation Manual Printed in USA 16 0213
Models SDB/SDP Installation & Operation Manual Printed in USA 17 0213
Models SDB/SDP Installation & Operation Manual Printed in USA 18 0213
Models SDB/SDP Installation & Operation Manual Warranty The terms and conditions set forth below together with those appearing on the face of the Acknowledgement (the “Order”) constitute the complete and exclusive agreement between Perlick Corporation and the Buyer pertaining to the goods and/or services identified in the Order. If there is a discrepancy or conflict between any exhibit or supplement to the Order and these terms and conditions, these terms and conditions shall control.
Models SDB/SDP Installation & Operation Manual When a return is authorized, a credit may be allowed pending an examination of the returned goods. The amount of the restocking charge will depend on the condition of the equipment. The minimum restocking charge for glass washers, bottle coolers, frosters, direct draws, cooler series back bars and accessory parts is 20%. The minimum restocking charge for custom series cabinets is 50%.
