Install Guide

ManualsBrandsPerlick ManualsInstallation AccessoriesPerlick Drain Pump For H50/H80C Clear Ice Makers

Drain Pump Kit for Undercounter Clear Ice Maker

For use with H50IM Series Clear Ice Makers

Form No. Z2334A, 02/25/2013

Check to ensure all parts are included:

Index

No. Description Qty.

1 Drain Pump Assembly 1

2 Vinyl Hose (drain hose) (5/8” ID x 6.5”) 1

3 Vinyl Hose (drain hose) (3/8” ID x 27.5”) 1

4 High Pressure Clear PVC Hose (discharge hose) (1/2” I.D.× 10’) 1

5 Small Clamp (vent hose to drain pump) 1

6 Medium Clamp (discharge hose to drain pump) 1

7 Large Clamp (drain hose/drain elbox to ice maker and drain pump) 2

8 Hose Clips (vent hose) 2

8a Truss Head Screw (4×8, SS) 2

Perlick Drain Pump

Catalog No. 63802A (Part No. HS-5061)

• Only qualied service technicians should install and service this drain pump to reduce the risk of death, electric shock,

serious injury or re. A plumbing permit and the services of a licensed plumber may be required in some areas.

• No installation or service should be undertaken until the technician has thoroughly read these instructions. Failure to

install, prime, operate, and maintain this drain pump in accordance with these instructions will adversely aect safety,

performance, component life, and warranty coverage and may result in costly water damage.

• Proper installation is the repsonsibility of the installer. Product failure or property damage due to improper installation is

not covered under the warranty.

• See the instruction manual provided with the icemaker for icemaker installation. Failure to install the icemaker within

these guidelines many adversely aect safety, performance, component life, and warranty coverage.

• Clean, sanitize and maintain the icemaker per the instructions provided in the icemaker’s instruction manual. If the

instruction manual is not available, consult with your local distributor or call Perlick Technical Service Support at (800)

558-5592 in the USA.

• THE ICEMAKER MUST BE GROUNDED: The icemaker is equipped with a 3-prong grounding plug to reduce the risk of

potential shock hazards. It must be plugged into a properly grounded, independent 3-prong wall outlet. If the outlet

is a 2-prong outlet, it is your personal responsibility to have a qualied electrician replace it with a properly grounded,

independent 3-prong wall outlet. Do not remove the ground plug from the power cord and do not use an adapter plug.

• The icemaker and this kit must be installed in accordance with applicable national, state, and local codes and

regulations.

• Protect the oor when moving the icemaker to prevent damage to the oor.

• This drain pump is approved for use only with the models listed.

WARNING

Summary of content (8 pages)

PAGE 1
Drain Pump Kit for Undercounter Clear Ice Maker For use with H50IM Series Clear Ice Makers Check to ensure all parts are included: Index No. Description Qty. 1 Drain Pump Assembly 1 2 Vinyl Hose (drain hose) (5/8” ID x 6.5”) 1 3 Vinyl Hose (drain hose) (3/8” ID x 27.5”) 1 4 High Pressure Clear PVC Hose (discharge hose) (1/2” I.D.
PAGE 2
Drain Pump Kit for Undercounter Clear Ice Makers For use with H50IMS, H50IMW and H50IMS-AD Clear Ice Makers INSTALLATION INSTRUCTIONS This drain pump is designed to remove drain water from an undercounter icemaker in areas without direct drainage access. The drain pump reservoir collects drain water and pumps it through a 1/2” ID high pressure clear pvc hose (discharge hose). The maximum discharge hose length is 20 feet. The maximum lift height is 8 feet.
PAGE 3
Drain Pump Kit for Undercounter Clear Ice Makers For use with H50IMS, H50IMW and H50IMS-AD Clear Ice Makers 5. Carefully place the drain pump into the open space provided at the rear of the icemaker. The drain pump will overhang the base slightly. (See Fig. 4). If necessary, carefully bend or move the icemaker’s copper tubing so that it does not make contact with the drain pump, hoses, or other parts of the icemaker.. CAUTION! Drain pump MUST be level. 6.
PAGE 4
Drain Pump Kit for Undercounter Clear Ice Makers For use with H50IMS, H50IMW and H50IMS-AD Clear Ice Makers 9. Cut the 3/8” ID vent hose to a length of 19.5” 10. On non -AD units, route the vent hose (3/8” I.D.×19.5”) through the drain fitting area (vent hose access area) in the rear access panel (see Fig. 6). 11. On -AD units, route the vent hose through the 23 mm diameter vent hose access hole in the rear access panel. (See Fig.7).
PAGE 5
Drain Pump Kit for Undercounter Clear Ice Makers For use with H50IMS, H50IMW and H50IMS-AD Clear Ice Makers 16. Connect the discharge hose to a suitable drain. Do not connect the discharge hose directly to a drain pipe or a floor drain. An air gap of a minimum of 2” (50.8 mm) should be between the end of the discharge hose and the floor drain or drain piping. NOTICE! Be sure there is a sufficient extra tubing for the unit to be pulled out for service.
PAGE 6
Drain Pump Kit for Undercounter Clear Ice Makers For use with H50IMS, H50IMW and H50IMS-AD Clear Ice Makers MAINTENANCE Clean, sanitize, and maintain the icemaker per the instructions provided in the icemaker’s instruction manual. If the instruction manual is not available, consult with your local distributor, visit www.perlick.com, or call Perlick Technical Service at (800) 558-5592 in the USA.
PAGE 7
Drain Pump Kit for Undercounter Clear Ice Makers For use with H50IMS, H50IMW and H50IMS-AD Clear Ice Makers Form No.
PAGE 8
300 West Good Hope Road • Milwaukee, WI 53223 • Toll Free 800.558.5592 • Fax 414.353.7069 • www.bringperlickhome.com Form No.