Use and Care

Form No. 67952
Rev. 06.05.14
Follow these instructions if you need to take the faucet apart to replace worn parts.
Note: Anytime the Front Seat (I), O-ring (H) or Coupling Gasket(s) are removed, they should be replaced.
Always use OEM replacement parts.
TO DISASSEMBLE:
1. If faucet is USED, soak faucet in warm cleaning solution for 1-2 minutes to free up bonnet and handle jacket.
If the faucet is NEW, submerge the faucet in warm water for 5 seconds.
2. Unscrew and remove Jacket (1).
3. Unscrew and remove Compression Bonnet (2).
4. Remove Coupling Gasket (8) only if cut or worn.
5. To remove the Handle Lever Assembly (5A or 5B), lift it upward and push back.
6. To remove Front Seat (7) use a small screwdriver from the bonnet end of the faucet.
7. To remove O-ring (6) use a small screwdriver from the bonnet end of the faucet.
8. Inspect O-rings for wear or damage and replace as necessary.
9. To remove ow control lever, unscrew cap and pull out.
10. Remove ow control compensator from rear of faucet.
TO ASSEMBLE:
1. Re-install O-ring (6) into O-ring groove from bonnet end (use a small blunt screwdriver).
2. Re-install front Seat (7) into O-ring groove (use a small blunt screwdriver). Note: Seat must move freely in seat
groove.
3. Re-install Handle Lever Assembly (5A or 5B).
4. Re-install Bearing Cup (4).
5. Re-install Bonnet Washer (3) into Compression Bonnet (2).
6. Re-install Compression Bonnet (2). Tighten by hand only. Do not use any tool, as this can damage the faucet.
7. Re-install Handle Jacket (1).
8. Re-install Coupling Gasket (8) if removed.
9. Install ow control compensator into rear of faucet and orientate so level engagement hole is facing lever insertion
hole.
10. Install ow control lever, ensure pin on end of lever is aligned with compensator engagement hole and tighten cap.
PERLICK CORPORATION 8300 W. Good Hope Rd., Milwaukee, WI 53223 • 800.558.5592 • perlick.com
PRODUCT SPECIFICATION SHEETS  Assembly, Disassembly and Cleaning Instructions
FORWARD SEALING BEER FAUCETS
U.S. PATENT #8066257
Faucet Replacement Parts
Item 630 680 650 690 Description
1
67829-1 67829-1 67829-1 67829-1 Handle Jacket, Chrome
67829-1TF 67829-1TF N/A N/A Handle Jacket, Tarnish Free
2
67820-1 67820-1 67820-1 67820-1 Compression Bonnet, Chrome
67820-1TF 67820-1TF N/A N/A Compression Bonnet, Tarnish Free
3 67828-1 67828-1 67828-1 67828-1 O-Ring, Compression
4 67819-2 67819-2 67819-2 67819-2 Bearing Cup
5A 68726-1 N/A 68626-1 N/A Handle Lever
5B N/A 68810 N/A 68810 Handle Lever, Push Back Creamer
6 67830-1 67830-1 67830-1 67830-1 O-Ring, Pivot Ball
7 67933-1 67933-1 67933-1 67933-1 O-Ring, Front Seat
8 308-3-2P 308-3-2P 308-3-2P 308-3-2P Coupling Gasket
9 N/A N/A 68206-1 68206-1 Flow Control: Compensator
10 N/A N/A 67989SK 67989SK Flow Control: Seal Kit
11 N/A N/A 67989LK 67989LK Flow Control: Lever & Seal Kit