Server User Manual
Table Of Contents
- SDS/SCS/STS/MDC User’s Guide
- Table of Contents
- Preface
- Introduction
- Hardware and Connectivity
- Configuration Methods
- Getting Started
- Using DeviceManager and WebManager
- Network Settings
- Configuring Serial Ports
- Introduction
- Serial Ports
- Serial Port Profiles
- Common Tabs
- Console Management Profile
- TruePort Profile
- TCP Sockets Profile
- UDP Sockets Profile
- Terminal Profile
- User Service Settings
- Printer Profile
- Serial Tunneling Profile
- Virtual Modem Profile
- Control Signal I/O Profile
- Modbus Gateway Profile
- Power Management Profile
- Remote Access (PPP) Profile
- Remote Access (SLIP) Profile
- Custom Application Profile
- Port Buffering
- Advanced
- Configuring Users
- Configuring Security
- Configuring I/O Interfaces
- Configuring Clustering
- Configuring the Option Card
- Configuring the System
- Controlling the RPS, I/O Channels, and IPsec Tunnels
- System Administration
- Introduction
- Managing Configuration Files
- Downloading IOLAN Firmware
- Calibrating I/O
- Setting the IOLAN’s Date and Time
- Rebooting the IOLAN
- Resetting the IOLAN to Factory Defaults
- Resetting the SecurID Node Secret
- Language Support
- Downloading Terminal Definitions
- Resetting Configuration Parameters
- Lost Admin Password
- Applications
- RADIUS and TACACS+
- SSL/TLS Ciphers
- Virtual Modem AT Commands
- Pinouts and Cabling Diagrams
- Setting Jumpers
- I/O Wiring Diagrams
- Utilities
- Accessories
- Troubleshooting
- Introduction
- Hardware Troubleshooting
- Communication Issues
- DeviceManager Problems
- Host Problems
- RADIUS Authentication Problems
- Login Problems
- Problems with Terminals
- Unknown IP Address
- DHCP/BOOTP Problems
- Callback Problems
- Language Problems
- Modem Problems
- PPP Problems
- Printing Problems
- Long Reboot Cycle
- SSL/TLS
- I/O Models
- IPv6 Issues
- Contacting Technical Support
- Glossary
- Index
IOLAN+ Interface
68 IOLAN SDS/SCS/STS/MDC User’s Guide, Version 4.0
Changes to the IOLAN+ Interface
You should be aware that the following IOLAN+ configuration fields are no longer supported:
z You no longer have the option of selecting access, Authentication/Logging. Also, kill, reboot,
and
stats are not available.
z When you select port, the following fields are not available on the Port Setup Menu:
** Administrator ** PORT SETUP MENU REMOTE-ADMIN
Hardware Flow ctrl Keys
Speed [9600 ] Flow ctrl [None ] Hot [^A] Intr [^C]
Parity [None ] Input Flow [Enabled ] Quit [^]] Kill [^\]
Bit [8] Output Flow [Enabled ] Del [^H] Sess N/A
Stop [1 ] Echo [^E]
Break [Disabled] IP Addresses
Monitor DSR [No ] Src [ ] Mask [ ]
Monitor DCD [No ] Dst [ ]
Interface [EIA-232] Access
User Options Access [Local ]
Name [abcd ] Keepalive [No ] UDP Retries N/A
Terminal type [dumb ] Rlogin/Telnet N/A Retry Interval N/A
TERM [ ] Debug options N/A Authentication N/A
Video pages [5] Map CR to CR LF [No ] Mode [Raw ]
CLI/Menu [CLI ] Hex data N/A Connection [None ]
Reset Term [No ] Secure N/A Host [ ]
MOTD [Yes ] Remote Port [0 ]
Local Port [10001]
________________________________________________________________________________
z User, Name—only when using LPD/LPR, Name no longer is used as the queue name
z Options, Rlogin/Telnet
z Options, Debug options
z Options, Hex data
z Options, Secure
z Keys, Sess
z Access, UDP Retries
z Access, Retry Interval
z Access, Authentication