Server User Manual
Table Of Contents
- SDS/SCS/STS/MDC User’s Guide
- Table of Contents
- Preface
- Introduction
- Hardware and Connectivity
- Configuration Methods
- Getting Started
- Using DeviceManager and WebManager
- Network Settings
- Configuring Serial Ports
- Introduction
- Serial Ports
- Serial Port Profiles
- Common Tabs
- Console Management Profile
- TruePort Profile
- TCP Sockets Profile
- UDP Sockets Profile
- Terminal Profile
- User Service Settings
- Printer Profile
- Serial Tunneling Profile
- Virtual Modem Profile
- Control Signal I/O Profile
- Modbus Gateway Profile
- Power Management Profile
- Remote Access (PPP) Profile
- Remote Access (SLIP) Profile
- Custom Application Profile
- Port Buffering
- Advanced
- Configuring Users
- Configuring Security
- Configuring I/O Interfaces
- Configuring Clustering
- Configuring the Option Card
- Configuring the System
- Controlling the RPS, I/O Channels, and IPsec Tunnels
- System Administration
- Introduction
- Managing Configuration Files
- Downloading IOLAN Firmware
- Calibrating I/O
- Setting the IOLAN’s Date and Time
- Rebooting the IOLAN
- Resetting the IOLAN to Factory Defaults
- Resetting the SecurID Node Secret
- Language Support
- Downloading Terminal Definitions
- Resetting Configuration Parameters
- Lost Admin Password
- Applications
- RADIUS and TACACS+
- SSL/TLS Ciphers
- Virtual Modem AT Commands
- Pinouts and Cabling Diagrams
- Setting Jumpers
- I/O Wiring Diagrams
- Utilities
- Accessories
- Troubleshooting
- Introduction
- Hardware Troubleshooting
- Communication Issues
- DeviceManager Problems
- Host Problems
- RADIUS Authentication Problems
- Login Problems
- Problems with Terminals
- Unknown IP Address
- DHCP/BOOTP Problems
- Callback Problems
- Language Problems
- Modem Problems
- PPP Problems
- Printing Problems
- Long Reboot Cycle
- SSL/TLS
- I/O Models
- IPv6 Issues
- Contacting Technical Support
- Glossary
- Index
Configuration Methods 65
SNMP
SNMP
Overview
The IOLAN supports configuration and management through SNMP. SNMP Management tools
(SNMP client/MIB browser software) can be used to set IOLAN configuration parameters and/or
view IOLAN statistics.
Before you can configure/manage the IOLAN using SNMP, you need to set the IOLAN IP address
and configure a read-write user for SNMP version 3 or a community for SNMP version 1 or 2. You
can use DeviceManager, CLI, or the Menu to set the IP address and user/community (don’t forget to
reboot the IOLAN before connecting with the SNMP manager to make your changes take effect).
Access Platforms
You can access the IOLAN SNMP MIB from any system that runs your SNMP client/MIB browser
software.
Features
SNMP supports the following features:
z You can configure SNMP traps.
z Since not all versions of SNMP support secure communication, password parameters must be set
using another configuration method.
Connecting to the IOLAN Using SNMP
Before you can connect to the IOLAN through an SNMP Management tool or MIB browser, you
need to set the following components through another configuration method.
1. Configure a known IP address on the IOLAN.
2. Configure a read-write user for SNMP version 3 or a community for SNMP version 1 or 2 on the
IOLAN.
3. Reboot the IOLAN to make sure the changes take effect.
To connect to the IOLAN through an SNMP Management tool or MIB browser, do the following:
1. Load the perle-sds.MIB file from the IOLAN CD-ROM or Perle website into your SNMP
manager (this MIB works for all SDS, SCS, STS, and MDC models).
Note:
You need to have the following MIBs installed in your SNMP manager (these are
usually part of the standard SNMP client/MIB browser):
z SNMPv2-SMI
z SNMPv2-TC
z IPV6-TC
2. Verify that the read-write user for SNMP version 3 or a community for SNMP version 1 or 2
match the configuration on the IOLAN.
3. Type in the IOLAN’s IP address and connect to the IOLAN.
You are now ready to start configuring the IOLAN using SNMP.