Server User Manual
Table Of Contents
- SDS/SCS/STS/MDC User’s Guide
- Table of Contents
- Preface
- Introduction
- Hardware and Connectivity
- Configuration Methods
- Getting Started
- Using DeviceManager and WebManager
- Network Settings
- Configuring Serial Ports
- Introduction
- Serial Ports
- Serial Port Profiles
- Common Tabs
- Console Management Profile
- TruePort Profile
- TCP Sockets Profile
- UDP Sockets Profile
- Terminal Profile
- User Service Settings
- Printer Profile
- Serial Tunneling Profile
- Virtual Modem Profile
- Control Signal I/O Profile
- Modbus Gateway Profile
- Power Management Profile
- Remote Access (PPP) Profile
- Remote Access (SLIP) Profile
- Custom Application Profile
- Port Buffering
- Advanced
- Configuring Users
- Configuring Security
- Configuring I/O Interfaces
- Configuring Clustering
- Configuring the Option Card
- Configuring the System
- Controlling the RPS, I/O Channels, and IPsec Tunnels
- System Administration
- Introduction
- Managing Configuration Files
- Downloading IOLAN Firmware
- Calibrating I/O
- Setting the IOLAN’s Date and Time
- Rebooting the IOLAN
- Resetting the IOLAN to Factory Defaults
- Resetting the SecurID Node Secret
- Language Support
- Downloading Terminal Definitions
- Resetting Configuration Parameters
- Lost Admin Password
- Applications
- RADIUS and TACACS+
- SSL/TLS Ciphers
- Virtual Modem AT Commands
- Pinouts and Cabling Diagrams
- Setting Jumpers
- I/O Wiring Diagrams
- Utilities
- Accessories
- Troubleshooting
- Introduction
- Hardware Troubleshooting
- Communication Issues
- DeviceManager Problems
- Host Problems
- RADIUS Authentication Problems
- Login Problems
- Problems with Terminals
- Unknown IP Address
- DHCP/BOOTP Problems
- Callback Problems
- Language Problems
- Modem Problems
- PPP Problems
- Printing Problems
- Long Reboot Cycle
- SSL/TLS
- I/O Models
- IPv6 Issues
- Contacting Technical Support
- Glossary
- Index
Configuration Methods 63
DHCP/BOOTP
DHCP/BOOTP
Overview
Several IOLAN parameters can be configured through a DHCP/BOOTP server during the IOLAN
bootup. This is particularly useful for configuring multiple IOLANs.
Not all configuration parameters are supported in the DHCP/BOOTP configuration (see
DHCP/BOOTP Parameters on page 64 for supported configuration parameters), so you will need to
use another configuration method, such as DeviceManager, WebManager or CLI, to complete the
configuration.
Features
DHCP/BOOTP supports the following features:
z DHCP/BOOTP can supply the IOLAN’s IP address.
z The DHCP/BOOTP server can configure certain server and user configuration parameters when
the IOLAN is booted.
z The DHCP/BOOTP server can auto-configure the IOLAN with basic setup information (IP
address, subnet/prefix bits, etc.).
z The DHCP/BOOTP server can download a new version of firmware when the IOLAN is
rebooted.
z The DHCP/BOOTP server can download a full configuration file when the IOLAN is rebooted.
Connecting to the IOLAN Using DHCP/BOOTP
The IOLAN will automatically request an IP address from the DCHP/BOOTP server when the
Obtain IP address automatically using DHCP/BOOTP parameter is enabled. To enable the Obtain
IP address automatically using DHCP/BOOTP
parameter, follow the directions in Using a Direct
Serial Connection to Enable BOOTP/DHCP on page 77.
Using DHCP/BOOTP
To use DHCP/BOOTP, edit the bootp file with IOLAN configuration parameters. You can use
DHCP/BOOTP to perform the following actions on a single or multiple IOLANs on bootup:
z auto-configure with minimal information; for example, only an IP address
z auto-configure with basic setup information (IP address, subnet/prefix bits, etc.)
z download a new version of firmware
z download a full configuration file
DHCP/BOOTP is particularly useful for multiple installations: you can do all the IOLANs’
configuration in one DHCP/BOOTP file, rather than configure each IOLAN manually. Another
advantage of DHCP/BOOTP is that you can connect the IOLAN to the network, turn on its power
and let autoconfiguration take place. All the configuration is carried out for you during the
DHCP/BOOTP process.