Server User Manual
Table Of Contents
- SDS/SCS/STS/MDC User’s Guide
- Table of Contents
- Preface
- Introduction
- Hardware and Connectivity
- Configuration Methods
- Getting Started
- Using DeviceManager and WebManager
- Network Settings
- Configuring Serial Ports
- Introduction
- Serial Ports
- Serial Port Profiles
- Common Tabs
- Console Management Profile
- TruePort Profile
- TCP Sockets Profile
- UDP Sockets Profile
- Terminal Profile
- User Service Settings
- Printer Profile
- Serial Tunneling Profile
- Virtual Modem Profile
- Control Signal I/O Profile
- Modbus Gateway Profile
- Power Management Profile
- Remote Access (PPP) Profile
- Remote Access (SLIP) Profile
- Custom Application Profile
- Port Buffering
- Advanced
- Configuring Users
- Configuring Security
- Configuring I/O Interfaces
- Configuring Clustering
- Configuring the Option Card
- Configuring the System
- Controlling the RPS, I/O Channels, and IPsec Tunnels
- System Administration
- Introduction
- Managing Configuration Files
- Downloading IOLAN Firmware
- Calibrating I/O
- Setting the IOLAN’s Date and Time
- Rebooting the IOLAN
- Resetting the IOLAN to Factory Defaults
- Resetting the SecurID Node Secret
- Language Support
- Downloading Terminal Definitions
- Resetting Configuration Parameters
- Lost Admin Password
- Applications
- RADIUS and TACACS+
- SSL/TLS Ciphers
- Virtual Modem AT Commands
- Pinouts and Cabling Diagrams
- Setting Jumpers
- I/O Wiring Diagrams
- Utilities
- Accessories
- Troubleshooting
- Introduction
- Hardware Troubleshooting
- Communication Issues
- DeviceManager Problems
- Host Problems
- RADIUS Authentication Problems
- Login Problems
- Problems with Terminals
- Unknown IP Address
- DHCP/BOOTP Problems
- Callback Problems
- Language Problems
- Modem Problems
- PPP Problems
- Printing Problems
- Long Reboot Cycle
- SSL/TLS
- I/O Models
- IPv6 Issues
- Contacting Technical Support
- Glossary
- Index
IOLAN SDS/SCS/STS/MDC User’s Guide, Version 4.0 391
Utilities Appendix G
G
Introduction
This chapter provides information on the TruePort and Decoder utilities.
TruePort
TruePort is a com port redirector utility for the IOLAN. It can be run in two modes:
z TruePort Full mode—This mode allows complete device control and operates exactly like a
directly connected serial port. It provides a complete COM port interface between the attached
serial device and the network.
z TruePort Lite mode—This mode provides a simple raw data interface between the device and
the network. Although the port will still operate as a COM port, control signals are ignored. In
this mode, the serial communications parameters must be configured on the IOLAN.
You use TruePort when you want to connect extra terminals to a server using the IOLAN rather than
a multi-port serial card. TruePort is especially useful when you want to improve data security, as you
can enable an SSL/TLS connection between the TruePort host port and the IOLAN. When run on
UNIX, TruePort allows you to print directly from a terminal to an attached printer (transparent
printing). You can also remap the slow baud rate of your UNIX server to a faster baud rate, as shown
below.
perle
Network
Serial Connection
Ethernet
UNIX, running
TruePort Daemon,
baud rate 4,800
Map UNIX baud
rate 4,800 to
230,400 for faster
throughput
PC
Currently, TruePort is supported on Linux, Windows, SCO, Solaris, and others. For a complete list of
of supported operating systems, see the Perle website.
For more information, see the TruePort User Guide or the TruePort Installation and Configuration
Guide for Windows NT on the CD-ROM.