Server User Manual
Table Of Contents
- SDS/SCS/STS/MDC User’s Guide
- Table of Contents
- Preface
- Introduction
- Hardware and Connectivity
- Configuration Methods
- Getting Started
- Using DeviceManager and WebManager
- Network Settings
- Configuring Serial Ports
- Introduction
- Serial Ports
- Serial Port Profiles
- Common Tabs
- Console Management Profile
- TruePort Profile
- TCP Sockets Profile
- UDP Sockets Profile
- Terminal Profile
- User Service Settings
- Printer Profile
- Serial Tunneling Profile
- Virtual Modem Profile
- Control Signal I/O Profile
- Modbus Gateway Profile
- Power Management Profile
- Remote Access (PPP) Profile
- Remote Access (SLIP) Profile
- Custom Application Profile
- Port Buffering
- Advanced
- Configuring Users
- Configuring Security
- Configuring I/O Interfaces
- Configuring Clustering
- Configuring the Option Card
- Configuring the System
- Controlling the RPS, I/O Channels, and IPsec Tunnels
- System Administration
- Introduction
- Managing Configuration Files
- Downloading IOLAN Firmware
- Calibrating I/O
- Setting the IOLAN’s Date and Time
- Rebooting the IOLAN
- Resetting the IOLAN to Factory Defaults
- Resetting the SecurID Node Secret
- Language Support
- Downloading Terminal Definitions
- Resetting Configuration Parameters
- Lost Admin Password
- Applications
- RADIUS and TACACS+
- SSL/TLS Ciphers
- Virtual Modem AT Commands
- Pinouts and Cabling Diagrams
- Setting Jumpers
- I/O Wiring Diagrams
- Utilities
- Accessories
- Troubleshooting
- Introduction
- Hardware Troubleshooting
- Communication Issues
- DeviceManager Problems
- Host Problems
- RADIUS Authentication Problems
- Login Problems
- Problems with Terminals
- Unknown IP Address
- DHCP/BOOTP Problems
- Callback Problems
- Language Problems
- Modem Problems
- PPP Problems
- Printing Problems
- Long Reboot Cycle
- SSL/TLS
- I/O Models
- IPv6 Issues
- Contacting Technical Support
- Glossary
- Index
Management
308 IOLAN SDS/SCS/STS/MDC User’s Guide, Version 4.0
Advanced
Overview
Review the configuration options in the Advanced page to determine if any of them apply to your
implementation.
Login Tab Field Descriptions
Configure the following parameters:
Use System Name
in Prompts
Display Login
Banner
Use Custom Login
Prompt
Bypass Login
Password
Use a Generic
WebManager
Login Screen
Password Retry
Limit
Displays the System Name field value instead of default product name. When
enabled, the
Server Name is displayed in the IOLAN login prompt, CLI
prompt, WebManager login screen, and the heading of the Menu.
Default: Disabled
This parameter concerns the banner information (product name/software
version). This banner information is presented to a user with a login prompt.
For security reasons, you can turn off the display of this information.
Default: Disabled
When set, and a custom language file is in use, the login prompt will use the
string defined in the language file as the login prompt instead of the default
prompt,
login:.
Default: Disabled
When set, authorized users who do not have a password set, with the exception
of the Admin user, WILL NOT be prompted for a password at login with
Local
Authentication
.
Default: Disabled
When set, and the user connects to the IOLAN using WebManager, the
WebManager login screen that is displayed is generic — the Perle banner,
IOLAN model name, and firmware version are not displayed to the user.
Default: Disabled
The number of attempts a user is allowed to enter a password for a serial port
connection from the network, before the connection is terminated and the user
has to attempt to login again. For users logging into the serial port, if this limit
is exceeded, the serial port is disabled for 5 minutes. A user with Admin level
rights can restart the serial port, bypassing the timeout, by issuing a kill on the
disabled serial port.
Default: 3