Server User Manual
Table Of Contents
- SDS/SCS/STS/MDC User’s Guide
- Table of Contents
- Preface
- Introduction
- Hardware and Connectivity
- Configuration Methods
- Getting Started
- Using DeviceManager and WebManager
- Network Settings
- Configuring Serial Ports
- Introduction
- Serial Ports
- Serial Port Profiles
- Common Tabs
- Console Management Profile
- TruePort Profile
- TCP Sockets Profile
- UDP Sockets Profile
- Terminal Profile
- User Service Settings
- Printer Profile
- Serial Tunneling Profile
- Virtual Modem Profile
- Control Signal I/O Profile
- Modbus Gateway Profile
- Power Management Profile
- Remote Access (PPP) Profile
- Remote Access (SLIP) Profile
- Custom Application Profile
- Port Buffering
- Advanced
- Configuring Users
- Configuring Security
- Configuring I/O Interfaces
- Configuring Clustering
- Configuring the Option Card
- Configuring the System
- Controlling the RPS, I/O Channels, and IPsec Tunnels
- System Administration
- Introduction
- Managing Configuration Files
- Downloading IOLAN Firmware
- Calibrating I/O
- Setting the IOLAN’s Date and Time
- Rebooting the IOLAN
- Resetting the IOLAN to Factory Defaults
- Resetting the SecurID Node Secret
- Language Support
- Downloading Terminal Definitions
- Resetting Configuration Parameters
- Lost Admin Password
- Applications
- RADIUS and TACACS+
- SSL/TLS Ciphers
- Virtual Modem AT Commands
- Pinouts and Cabling Diagrams
- Setting Jumpers
- I/O Wiring Diagrams
- Utilities
- Accessories
- Troubleshooting
- Introduction
- Hardware Troubleshooting
- Communication Issues
- DeviceManager Problems
- Host Problems
- RADIUS Authentication Problems
- Login Problems
- Problems with Terminals
- Unknown IP Address
- DHCP/BOOTP Problems
- Callback Problems
- Language Problems
- Modem Problems
- PPP Problems
- Printing Problems
- Long Reboot Cycle
- SSL/TLS
- I/O Models
- IPv6 Issues
- Contacting Technical Support
- Glossary
- Index

185
Serial Port Profiles
Password Complete this field only if you have specified PAP or CHAP (security
protocols) in the
Security field and:
z you wish to dedicate this serial port to a single remote user, who will be
authenticated by the IOLAN, or
z you are using the IOLAN as a router (back-to-back with another IOLAN)
Password means the following:
z When PAP is specified, this is the password the remote device will use to
authenticate the port on this IOLAN.
z When CHAP is specified, this is the secret (password) known to both ends
of the link upon which responses to challenges shall be based.
Field Format: You can enter a maximum of 16 alphanumeric characters.
Remote User Complete this field only if you have specified PAP or CHAP (security
protocols) in the
Security field, and
z you wish to dedicate this line to a single remote user, who will be
authenticated by the IOLAN, or
z you are using the IOLAN as a router (back-to-back with another IOLAN)
When
Dial In or Dial In/Dial Out is enabled, the Remote User is the name the
IOLAN will use to authenticate the port on the remote device. Your IOLAN
will only authenticate the port on the remote device when
PAP or CHAP are
operating. When connecting together two networks, enter a dummy user name;
for example, DS_SALES.
Note If you want a reasonable level of security, the user name and password
should not be similar to a user name or password used regularly to login to the
IOLAN. This option does not work with external authentication.
Field Format: You can enter a maximum of 254 alphanumeric characters.
Remote Password Complete this field only if you have specified PAP or CHAP (security
protocols) in the
Security field, and
z you wish to dedicate this serial port to a single remote user, and this user
will be authenticated by the IOLAN, or
z you are using the IOLAN as a router (back-to-back with another IOLAN)
Remote password means the following:
z When PAP is specified, this is the password the IOLAN will use to
authenticate the remote device.
z When CHAP is specified, this is the secret (password) known to both ends
of the link upon which responses to challenges will be based.
Remote Password is the opposite of the parameter Password. Your IOLAN
will only authenticate the remote device when
PAP or CHAP is operating.
Field Format: You can enter a maximum of 16 alphanumeric characters.
Authentication
Timeout
The timeout, in minutes, during which successful PAP or CHAP authentication
must take place (when PAP or CHAP are specified). If the timer expires before
the remote end has been authenticated successfully, the link will be terminated.
Range: 1-255
Default: 1 minute










