Server User Manual
Table Of Contents
- SDS/SCS/STS/MDC User’s Guide
- Table of Contents
- Preface
- Introduction
- Hardware and Connectivity
- Configuration Methods
- Getting Started
- Using DeviceManager and WebManager
- Network Settings
- Configuring Serial Ports
- Introduction
- Serial Ports
- Serial Port Profiles
- Common Tabs
- Console Management Profile
- TruePort Profile
- TCP Sockets Profile
- UDP Sockets Profile
- Terminal Profile
- User Service Settings
- Printer Profile
- Serial Tunneling Profile
- Virtual Modem Profile
- Control Signal I/O Profile
- Modbus Gateway Profile
- Power Management Profile
- Remote Access (PPP) Profile
- Remote Access (SLIP) Profile
- Custom Application Profile
- Port Buffering
- Advanced
- Configuring Users
- Configuring Security
- Configuring I/O Interfaces
- Configuring Clustering
- Configuring the Option Card
- Configuring the System
- Controlling the RPS, I/O Channels, and IPsec Tunnels
- System Administration
- Introduction
- Managing Configuration Files
- Downloading IOLAN Firmware
- Calibrating I/O
- Setting the IOLAN’s Date and Time
- Rebooting the IOLAN
- Resetting the IOLAN to Factory Defaults
- Resetting the SecurID Node Secret
- Language Support
- Downloading Terminal Definitions
- Resetting Configuration Parameters
- Lost Admin Password
- Applications
- RADIUS and TACACS+
- SSL/TLS Ciphers
- Virtual Modem AT Commands
- Pinouts and Cabling Diagrams
- Setting Jumpers
- I/O Wiring Diagrams
- Utilities
- Accessories
- Troubleshooting
- Introduction
- Hardware Troubleshooting
- Communication Issues
- DeviceManager Problems
- Host Problems
- RADIUS Authentication Problems
- Login Problems
- Problems with Terminals
- Unknown IP Address
- DHCP/BOOTP Problems
- Callback Problems
- Language Problems
- Modem Problems
- PPP Problems
- Printing Problems
- Long Reboot Cycle
- SSL/TLS
- I/O Models
- IPv6 Issues
- Contacting Technical Support
- Glossary
- Index
Serial Port Profiles
156 IOLAN SDS/SCS/STS/MDC User’s Guide, Version 4.0
PPP Settings
The PPP settings apply when the User Service is set to PPP.
Configure the following parameters:
IPv4 Local IP
Address
The IPV4 IP address of the IOLAN end of the PPP link. For routing to work,
you must enter a local IP address. Choose an address that is part of the same
network or subnetwork as the remote end; for example, if the remote end is
address 192.101.34.146, your local IP address can be 192.101.34.145. Do not
use the IOLAN’s (main) IP address in this field; if you do so, routing will not
take place correctly.
IPv4 Remote IP
Address
The IPV4 IP address of the remote end of the PPP link. Choose an address that
is part of the same network or subnetwork as the IOLAN. If you set the PPP
parameter IP Address Negotiation to On, the IOLAN will ignore the remote IP
address value you enter here and will allow the remote end to specify its IP
address. If your user is authenticated by RADIUS and the RADIUS parameter
Framed-Address is set in the RADIUS file, the IOLAN will use the value in
the RADIUS file in preference to the value configured here. The exception to
this rule is a
Framed-Address value in the RADIUS file of 255.255.255.254;
this value allows the IOLAN to use the remote IP address value configured
here.
IPv4 Subnet Mask The network subnet mask. For example, 255.255.0.0. If your user is
authenticated by RADIUS and the RADIUS parameter
Framed-Netmask is set
in the RADIUS file, the IOLAN will use the value in the RADIUS file in
preference to the value configured here.
IPv6 Local
Interface Identifier
The local IPv6 interface identifier of the IOLAN end of the PPP link. For
routing to work, you must enter a local IP address. Choose an address that is
part of the same network or subnetwork as the remote end. Do not use the
IOLAN’s (main) IP address in this field; if you do so, routing will not take
place correctly.
Field Format: The first 64 bits of the Interface Identifier must be zero,
therefore, ::abcd:abcd:abcd:abcd is the expected format.