Server User Manual
Table Of Contents
- SDS/SCS/STS/MDC User’s Guide
- Table of Contents
- Preface
- Introduction
- Hardware and Connectivity
- Configuration Methods
- Getting Started
- Using DeviceManager and WebManager
- Network Settings
- Configuring Serial Ports
- Introduction
- Serial Ports
- Serial Port Profiles
- Common Tabs
- Console Management Profile
- TruePort Profile
- TCP Sockets Profile
- UDP Sockets Profile
- Terminal Profile
- User Service Settings
- Printer Profile
- Serial Tunneling Profile
- Virtual Modem Profile
- Control Signal I/O Profile
- Modbus Gateway Profile
- Power Management Profile
- Remote Access (PPP) Profile
- Remote Access (SLIP) Profile
- Custom Application Profile
- Port Buffering
- Advanced
- Configuring Users
- Configuring Security
- Configuring I/O Interfaces
- Configuring Clustering
- Configuring the Option Card
- Configuring the System
- Controlling the RPS, I/O Channels, and IPsec Tunnels
- System Administration
- Introduction
- Managing Configuration Files
- Downloading IOLAN Firmware
- Calibrating I/O
- Setting the IOLAN’s Date and Time
- Rebooting the IOLAN
- Resetting the IOLAN to Factory Defaults
- Resetting the SecurID Node Secret
- Language Support
- Downloading Terminal Definitions
- Resetting Configuration Parameters
- Lost Admin Password
- Applications
- RADIUS and TACACS+
- SSL/TLS Ciphers
- Virtual Modem AT Commands
- Pinouts and Cabling Diagrams
- Setting Jumpers
- I/O Wiring Diagrams
- Utilities
- Accessories
- Troubleshooting
- Introduction
- Hardware Troubleshooting
- Communication Issues
- DeviceManager Problems
- Host Problems
- RADIUS Authentication Problems
- Login Problems
- Problems with Terminals
- Unknown IP Address
- DHCP/BOOTP Problems
- Callback Problems
- Language Problems
- Modem Problems
- PPP Problems
- Printing Problems
- Long Reboot Cycle
- SSL/TLS
- I/O Models
- IPv6 Issues
- Contacting Technical Support
- Glossary
- Index
Serial Port Profiles
154 IOLAN SDS/SCS/STS/MDC User’s Guide, Version 4.0
SLIP Settings
The SLIP settings apply when the User Service is set to SLIP.
Configure the following parameters:
SSH2 Ciphers
Opt1-5
Select the order of negotiation for the encryption method (ciphers) that the
IOLAN will use for the SSH version 2 connection:
Data Options:
z 3DES
z Blowfish
z AES
z Arcfour
z CAST
RSA When enabled, an authentication method used by SSH version 1 and 2. Use
RSA authentication for the SSH session.
Default: Enabled
DSA When enabled, an authentication method used by SSH version 2. Use DSA
authentication for the SSH session.
Default: Enabled
Keyboard
Authentication
When enabled, the user types in a password for authentication.
Default: Enabled
Local IP Address The IPv4 address of the IOLAN end of the SLIP link. For routing to work you
must enter an IP address in this field. Choose an address that is part of the same
network or subnetwork as the remote end; for example, if the remote end is
address 192.101.34.146, your local IP address can be 192.101.34.145. Do not
use the IOLAN’s (main) IP address in this field; if you do so, routing will not
take place correctly.
Remote IP Address The IPv4 address of the remote end of the SLIP link. Choose an address that is
part of the same network or subnetwork as the IOLAN. If your user is
authenticated by the IOLAN, this remote IP address will be overridden if you
have set a
Framed IP Address for the user. If your user is authenticated by
RADIUS and the RADIUS parameter
Framed-Address is set in the RADIUS
file, the IOLAN will use the value in the RADIUS file in preference to the
value configured here.
Subnet Mask The network subnet mask. For example, 255.255.0.0. If your user is
authenticated by RADIUS and the RADIUS parameter
Framed-Netmask is set
in the RADIUS file, the IOLAN will use the value in the RADIUS file in
preference to the value configured here.