Installation Guide

USCG APPROVAL
33 CFR 183.810
Visibility: Varies
Tested By: IMANNA Labs.
Dates: 2/25/03, 2/26/03,
6/18/03 & 6/20/03
Meets ABYC A-16
0200 Series Navigation Light Installation Instructions
Base Mount Series Lights
Removing and installing the lens
A) Molded mark or Red/Green lens joint.
B) Rotate clockwise to install.
C) Rotate counter-clockwise to remove.
Bulb Part Numbers
12V 10 Watt 037512V10W
12V 25 Watt 037512V25W
24V 10 Watt 037524V10W
24V 25 Watt 037524V25W
32V 10 Watt 037532V10W
32V 25 Watt 037532V25W
Base Mount Installation
1. Strip cable outer insulation to required length.
2. Install silicone sleeves. These are provided as protection against high
internal temperature.
3. Thread cable through gland.
4. Mount base (using #10 screws) with symbols (➯) parallel with boat
centerline.
5. Tighten gland.
6. Connect cables.
7. Install bulb at correct voltage and wattage, note staggered mounting pins.
8. Install lens. Turn clockwise firmly to stop.
Mounting holes can also be used to obtain correct alignment. Mount
tricolor, masthead and stern lights with holes at right angles to boat
centerline. Mount sidelights with holes parallel to boat centerline.
Electrical Connections
Attach supply connections to the light, making sure to wire in accordance
with both A.B.Y.C. Standard E-9* and U.S. Coast Guard Safety Standards
for Boat Electrical Systems (33 CFR 183)*.
Always use cable of sufficient size to ensure total voltage drop is less than
0.5 volt for a nominal 12 volt installation (1 volt drop with 24 volt
installations). Recommended minimum cable size 1.5mm
2
(No. 16 AWG.).
Bulbs - Use only PERKO replacement bulbs as shown to the right.
Cleaning: Use only fresh water and mild detergents to clean.
* The above referenced Standards can be obtained from.
1) American Boat & Yacht Council, Inc 2) U.S. Coast Guard
613 Third Street, Suite 10 Washington D.C. 20593
Annapolis, MD 21403 (or your local C.G. office)
10/14
0200INS1
Lens Cable
Gland
Cable
Grommet
Base
Gasket
2 Mounting
holes for
#10 screws
2-1/8” center to
center
AB CD E
Base Mount Light Diagram
1. Masthead White Bulb 25w
2. Port Red Bulb 25w
3. Starboard Green Bulb 25w
4. Stern White Bulb 10w
5. Bicolor Red/Grn Bulb 25w
6. Tricolor Red/Grn/Wht Bulb 25w
7. Anchor (Mast Top)✝ White Bulb 10w
8. Anchor (Halyard)✝ White Bulb 10w
✝. Signal White
Perko, Inc. • 16490 N.W. 13th Avenue • Miami, FL 33169-5707
The above lights are designed for use on sail and power driven
vessels under 20 meters (65.6 ft.) in length operating on a nominal
12 volt, 24 volt or 32 volt system. In order to comply with ‘72
COLREGS and the U.S. Inland Rules, the following must be
adhered to:
MOUNTING INFORMATION
Read all instructions before proceeding
For proper light selection, positioning and configuration, refer to
the A.B.Y.C. Standard A-16*, the ‘72 COLREGS* and the U.S.
Inland Rules*.
Consider the placement of the light to give:
a). Correct positioning of the light on the boat and
b). The most convenient positions for cleaning and bulb
changing.
To ensure the correct optical performance of the lights:
• Mount the red (port) and green (starboard) sidelights accurately
vertical in the same thwartship plane and at the same height
above the waterline at least one meter below the masthead
light with the symbol (➯) parallel with the boat centerline and
pointing to the bow. If a bicolor light is used, mount on the
centerline of the vessel at the bow at right angles to the
centerline and at least 1 meter below the masthead light.
• Mount the white masthead light vertical on the centerline clear
of all other lights with the symbol (➯) parallel with the boat
centerline pointing to the bow. On boats less then 12 meters,
mount at least 1 meter above the sidelights. On boats 12
meters and above but less than 20 meters, mount no less then
2.5 meters above the gunwale, and at least 1 meter above the
sidelights.
• Mount the white stern light vertical on the centerline and high
enough not to be obscured by a following sea, with the symbol
(➯) parallel with the boat centerline pointing to the bow.
• Mount the tricolor light on the mast top with the symbol (➯)
parallel with the boat centerline pointing to the bow. (Note:
Tricolor lights are only permitted on boats under sail)
Light
Visibility
0200 BB 2nm
0200 GRB 2nm/2nm
0200 MAB 3nm/2nm
0200 MB 3nm
0200 PB 2nm
0200 SDB 2nm
0200 SGB 2nm
0200 SNB 2nm
0200 SRB 2nm
0200 SWB 2nm
0200 TAB* 2nm/2nm
0200 TB* 2nm
0200 TWB 2nm
The above lights are all approved for 12V, 24V or
32V applications except where noted.
* Not Approved for 24V or 32V Applications