User Manual

Cooling system
Radiator
- face area. ... ... ... ... ... ... ... ... ... ... ... ... ... ... 0.276 m² (2.97 ft²)
- rows and materials.. ... ... ... ... ... ... ... ... .. double row aluminium
- matrix density and material . ... ... ... ... .. Aluminium 12,5 fins/inch
- width of matrix. ... ... ... ... ... ... ... ... ... ... ... ... .. 526 mm (20.7 in)
- height of matrix ... ... ... ... ... ... ... ... ... ... ... ... .. 524 mm (20.6 in)
- pressure cap setting ... ... ... ... ... ... ... ... ... ... ... ... ... ... 107 kPa
Fan
- diameter.. ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. 457 mm (18.0 in)
- drive ratio ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 1.25 : 1
- number of blades ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 7
- material ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... Composite
- type . ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..Pusher
Coolant
Total system capacity
- with radiator ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. 13,0 l (27.4 pt)
- without radiator ... ... ... ... ... ... ... ... ... ... ... ... ... ... 7,0 l (14.7 pt)
Maximum top tank temperature ... ... ... ... ... ... ... 110 °C (230 °F)
Thermostat operating range.. ... ... ... ... ..82 - 93 °C (180 - 199 °F)
Recommended coolant: 50 % ethylene glycol with a corrosion
inhibitor (BS 658 : 1992 or MOD AL39) and 50% clean fresh water.
Electrical system
Type .. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ...Negative ground
Alternator voltage .. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..12 V
Alternator output ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 65 amps
Starter motor voltage. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..12 V
Starter motor power .. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . 3 kW
Number of teeth on flywheel . ... ... ... ... ... ... ... ... ... ... ... ... ... 126
Pull in current of starter motor solenoid ... ... ... ... ... ... .. 60 amps
Hold in current of starter motor solenoid ... ... ... ... ... ... .. 15 amps
Engine stop solenoid. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ..12 V
Stop solenoid (minimum)
- pull in current .. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 10 amps
- hold in current . ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 10 amps
Cold start recommendations
Minimum cranking speed .. ... ... ... ... ... ... ... ... ... ... . 105 rev/min
Starter specification
* - Glow plug start aid fitted.
Note: CCA - Cold Cracking Amps to SAEJ537.
Notes:
z Battery capacity is defined by the 20 hour rate
z If a change to a low viscosity oil is made, the cranking torque
necessary at lower ambient temperatures is much reduced.
The starting equipment has been selected to take advantage
of this. It is important to change the appropriate multigrade oil
in anticipation of operating in low ambient temperatures.
z Breakaway current is dependent on battery capacity available.
Cables should be capable of handling the transient current
which may be up to double the steady cranking current.
Exhaust system
Maximum back pressure
- 1500 rev/min ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .10 kPa
- 1800 rev/min ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .15 kPa
Exhaust outlet size . ... ... ... ... ... ... ... ... ... ... ... ... .64 mm (2.5 in)
Fuel System
Type of injection . ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... .. Direct
Fuel injection pump ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . Rotary
Fuel atomiser.. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... Multi-hole
Nozzel opening pressure ... ... ... ... ... ... ... ... . 29,0 MPa (290 bar)
Fuel lift pump
Type ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . Electrical
-flow/hour ... ... ... ... ... ... ... ... ... ... . 120 - 150 l/h (211 - 264 pt/m)
-pressure ... ... ... ... ... ... ... ... ... ... ... . 30 - 75 kPa (4.4 - 10.9 psi)
Maximum suction head .. ... ... ... ... ... ... ... ... ... .20 kPa (2.90 psi)
Governor type
Electronic governor ... ... ... ... ... ... ... ... ... ... ... ..
Woodward LCS2
Electronic governor speed control to.. ... ... ... .ISO 8528, G3 (Hot)
Mechnical governor speed control to ... ... ... ISO 8528, G2 (Cold)
Fuel specification
Fuel consumption litres/hour (UK gals/hr)
Induction system
Maximum air intake restriction
-clean filter.. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 5,0 kPa
- dirty filter... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... 8,0 kPa
- air filter type.. ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... . Dry
Lubrication system
Lubricating oil capacity
Total system ... ... ... ... ... ... ... ... ... ... ... ... ... ... ... ...8,0 l (16.9 pt)
Sump minimum .. ... ... ... ... ... ... ... ... ... ... ... ... ... ...5,5 l (11.6 pt)
Sump maximum . ... ... ... ... ... ... ... ... ... ... ... ... ... .. 7,0 l (14.7 pt)
Maximum engine operating angles:
- front up, front down, right side or left side ... ... ... ... ... ... ... .. 25°
Lubricating oil pressure
- relief valve opens . ... ... ... ... ... ... ... ... ... ... ... ... . 415 - 470 kPa
- at maximum no-load speed .. ... ... ... ... ... ... ... ... . 276 - 414 kPa
Max continuous oil temperature . ... ... ... ... ... ... ...125 °C (257 °F)
Oil consumption at full load as a % of fuel consumption ... ..0.15%
Starter motor
type
Minimum
starting
temperature
Lubricating oil viscosity SAE / battery
type - values in CCA
12 volt
3.0 kW
°C (°F) 15W/40 10W/40 5W/40 5W/30
-10 (14) 1 x 900
-15 (5) * 1 x 900
-20 (-4) * 1 x 900
-25 (-13) * 2 x 570
Fuel Specification
European RF75-T-96 / DIN
EN590 / BS2869 class A2
Density (kg/l @ 15 °C) 0,835 - 0,845
Viscosity (mm²/s @ 40 °C) 2,5 - 3,5
Sulphur content (%) 0,1 - 0,2
Cetane number 45 - 50
1104A-44TG1 Power rating
Speed 110% 100% 75% 50% 25%
1500 16,5 (3.6) 14,8 (3.2) 11,2 (2.4) 8,0 (1.7) 4,6 (1.0)
1800 19,7 (4.3) 17,8 (3.9) 13,5 (2.9) 9,7 (2.1) 5,8 (1.2)
BDC for engine manuals and specs
https://barringtondieselclub.co.za/