UENR0622-02 (en-us) June 2016 Specifications 854E-E34TA, 854F-E34T and 854FE34TA Industrial Engines JR (Engine) JS (Engine) JT (Engine) JV (Engine) This document has been printed from SPI2.
Important Safety Information Most accidents that involve product operation, maintenance and repair are caused by failure to observe basic safety rules or precautions. An accident can often be avoided by recognizing potentially hazardous situations before an accident occurs. A person must be alert to potential hazards. This person should also have the necessary training, skills and tools to perform these functions properly.
UENR0622-02 3 Table of Contents Table of Contents Specifications Section Engine Design .....................................................4 Fuel Injection Lines ..............................................4 Fuel Injection Pump ..............................................5 Fuel Injectors .......................................................5 Fuel Filter Base (Secondary Fuel Filter Base)..........5 Fuel Filter Base (Primary Fuel Filter Base) ..............6 Fuel Manifold (Rail) .....................
UENR0622-02 Specifications Section Specifications Section Note: The left side and the right side of the engine are viewed from the flywheel end. The No. 1 cylinder is the front cylinder. i06719934 i05240674 Engine Design Fuel Injection Lines Contact with high pressure fuel may cause fluid penetration and burn hazards. High pressure fuel spray may cause a fire hazard. Failure to follow these inspection, maintenance and service instructions may cause personal injury or death.
UENR0622-02 Specifications Section (2) (3) Torque for the nuts on the fuel injection lines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 N·m ((18 lb ft)) i05240671 Fuel Injection Pump Refer to Operation and Maintenance Manual, “General Hazard Information and High Pressure Fuel Lines” before adjustments and repairs are performed.
UENR0622-02 Specifications Section NOTICE Refer to Systems Operation, Testing, and Adjusting, “Cleanliness of Fuel System Components” for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system. NOTICE Refer to Systems Operation, Testing, and Adjusting, “Cleanliness of Fuel System Components” for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system.
UENR0622-02 Specifications Section NOTICE Refer to Systems Operation, Testing and Adjusting, “Cleanliness of Fuel System Components” for detailed information on the standards of cleanliness that must be observed during ALL work on the fuel system. Illustration 7 g02621238 Typical example (1) Tighten the fuel pressure relief valve to the following torque. . . . . . . . . . . . . . . 100 N·m ((74 lb ft)) (2) Tighten the bolts to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section i04823040 Rocker Shaft Illustration 10 g02681778 Tightening sequence Tighten the fasteners in the sequence that is in illustration 10 . Tighten the fasteners to the following torque. . . . . . . . . . . . . . . . . . . . . . . 10 N·m ((89 lb in)) Illustration 9 g02842156 Typical example (1) Inlet rocker arm Diameter of the rocker arm bore . . . . . . . . . . . . . . . . . . . . . . . 19.020 to 19.033 mm ((0.74882 to 0.
UENR0622-02 9 Specifications Section i04335229 Valve Mechanism Cover Illustration 11 g02490536 Typical example Tighten the M6 fasteners (1), (2), (3), (4), (5), (6) and (7) in the sequence shown in illustration 11 to an initial torque. . . . . . . . . . . . . . . . . . . 5 N·m ((44 lb in)) Tighten the M8 fastener (8) in the sequence shown in illustration 11 to an initial torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 N·m ((89 lb in)) This document has been printed from SPI2.
UENR0622-02 Specifications Section Illustration 12 g02727663 Typical example Tighten the M6 fasteners (1), (2), (3), (4), (5), (6) and (7) in the sequence shown in illustration 12 to a final torque. . . . . . . . . . . . . . . . . . . . . . . 10 N·m ((89 lb in)) i04335069 Cylinder Head Valves Tighten the M8 fasteners (8), (9) and (10) in the sequence shown in illustration 12 to a final torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 11 Specifications Section The free length for the valve spring . . . . . . . . . . . . . . . . . . . . . . 44.6 mm ((1.75590 inch)) Table 1 The load for the valve spring The length of the valve spring 270 N (61 lb) 34 mm (1.33858 inch) 528 N (119 lb) 23.8 mm (0.93701 inch) Illustration 14 i05329586 Cylinder Head g01335204 (2) Valve face angle Inlet . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 degrees Exhaust . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section Illustration 16 g02490336 Note: The maximum distortion of the bottom face of the cylinder head is given in table 2 . Table 2 Dimension Maximum Permissible Distortion Width (A) 0.05 mm (0.00197 inch) Length (B) 0.05 mm (0.00197 inch) Diagonal Line (C) 0.05 mm (0.00197 inch) Illustration 17 g02328933 Typical example (D) Valve guide height from the top of the valve guide to the valve spring seat . . . . . . . . . . . . 8.5 ± 0.13 mm ((0.335 ± 0.
UENR0622-02 13 Specifications Section Illustration 19 g02847819 Typical example (L) Seat surface finish . . . . . . . . . . . . . Ra 0.5 microns Illustration 18 g02474819 Typical example (M) Concentricity of valve seat to valve guide parent bore Maximum Total Indicated Reading (TIR) . . . . . . . . . . . . . . . . . . . . . . 0.05 mm ((0.00197 inch)) (J) Diameter of the parent bore in the cylinder head . . . 12.960 to 12.995 mm ((0.51024 to 0.51161 inch)) (K) Seat angle Inlet . . . . . . . . . . .
UENR0622-02 Specifications Section i05239446 Turbocharger Illustration 21 g02626267 Typical example (2) Tighten the studs to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 N·m ((11 lb ft)) Illustration 20 g02626265 (3) Tighten the nuts to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 N·m ((18 lb ft)) Typical example (1) Actuator The test pressure for the wastegate actuator . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 15 Specifications Section i05239430 Exhaust Gas Valve (NRS) Illustration 23 g02626270 Typical example Illustration 24 g02626260 Typical example (6) Tighten the setscrew to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 N·m ((18 lb ft)) (7) Tighten the nut to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 N·m ((18 lb ft)) (1) Tighten the setscrews to the following torque. . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section i04426264 Exhaust Cooler (NRS) Illustration 25 i05239453 Exhaust Manifold g02621805 Illustration 26 g02909156 Typical example Typical example (1) Tighten the nuts to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 N·m ((18 lb ft)) (1) Tighten the studs to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 N·m ((13 lb ft)) (2) Tighten the fastener to the following torque. . . . . . . . . .
UENR0622-02 17 Specifications Section Illustration 27 g02725251 Typical example (2) Tighten the nuts to an initial torque. Tighten the nuts in the sequence that is shown in Illustration 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 N·m ((89 lb in)) i05287664 Flexible Exhaust Pipe (2) Tighten the nuts to a final torque. Tighten the nuts in the sequence that is shown in Illustration 27 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section i05287571 Diesel Particulate Filter (Wall Flow Diesel Particulate Filter (DPF)) Illustration 28 g03180056 Typical example (1) Tube assembly (4) Bellows (6) Elbow (2) Tighten the ball clamp to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35 N·m ((26 lb ft)) (3) Tighten the clamp to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 19 Specifications Section i05287843 Diesel Particulate Filter i05239470 Camshaft (Through Flow Diesel Particulate Filter (DPF)) Illustration 31 g02844377 Typical example Illustration 30 g03358495 Typical example (2) Diesel Particulate Filter (DPF) (3) Clamps (4) Mounting bracket (1) Tighten the bolts to an initial torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 N·m ((71 lb in)) (1) Tighten the bolts to a second torque. . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section i04411212 Camshaft Bearings Illustration 32 i05240691 Engine Oil Filter Base g02608336 Illustration 33 g02659546 Typical example Typical example (1) The diameter of the installed camshaft bearing . . .54.083 to 54.147 mm ((2.12925 to 2.13177 inch)) (1) Tighten the plug to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 N·m ((22 lb ft)) (2) Tighten the plug to the following torque. . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 21 Specifications Section i05240850 Engine Oil Cooler Illustration 34 i04346369 Engine Oil Pump g02871598 Illustration 35 g02501357 Typical example Typical example Tighten the setscrews in the sequence shown in illustration 34 to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 N·m ((16 lb ft)) (1) Tighten the bolts to an initial torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section i04789574 Engine Oil Pan (Pressed Steel Oil Pan) Illustration 36 g02904316 Typical example (1) Tighten the drain plug to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 N·m ((37 lb ft)) Tighten the fasteners (2) in sequence that is shown in illustration 37 . Tighten the M8 fasteners to an initial torque of 7.5 N·m (66 lb in). Tighten the M10 fasteners to an initial torque of 13.5 N·m (10 lb ft).
UENR0622-02 23 Specifications Section Illustration 37 g02904337 Tightening sequence for the pressed steel oil pan i04790655 Engine Oil Pan (Aluminum Oil Pan) This document has been printed from SPI2.
UENR0622-02 Specifications Section Illustration 38 g02906220 Typical example (1) Tighten the drain plug to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 N·m ((37 lb ft)) Tighten the fasteners (2) in sequence that is shown in illustration 39 . Tighten the M8 fasteners to an initial torque of 7.5 N·m (66 lb in). Tighten the M10 fasteners to an initial torque of 13.5 N·m (10 lb ft). Tighten the fasteners (2) in sequence that is shown in illustration 39 .
UENR0622-02 25 Specifications Section Illustration 39 g02906221 Tightening sequence i05288769 Engine Oil Pan (Cast Iron Oil Pan) This document has been printed from SPI2.
UENR0622-02 Specifications Section Illustration 40 g02676701 Typical example (1) Tighten the drain plug to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50 N·m ((37 lb ft)) Tighten the fasteners (2) to a torque of 70 N·m (52 lb ft). Tighten the fasteners in sequence that is shown in illustration 41 . This document has been printed from SPI2.
UENR0622-02 27 Specifications Section Illustration 41 g02904098 Tightening sequence for the deep tunnel oil pan Tighten the fasteners (2) to a torque of 70 N·m (52 lb ft). Tighten the fasteners in sequence that is shown in illustration 42 . This document has been printed from SPI2.
UENR0622-02 Specifications Section Illustration 42 g02904216 Tightening sequence for the flat bottom oil pan i05239495 Crankcase Breather For the correct procedures to remove and install the crankcase breather, refer to Disassembly and Assembly, “Crankcase Breather - Remove” and Disassembly and Assembly, “Crankcase Breather Install”. This document has been printed from SPI2.
UENR0622-02 29 Specifications Section i04335212 Water Temperature Regulator and Housing Illustration 43 g02721003 Typical example (1) Tighten the studs to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 N·m ((71 lb in)) (2) Tighten the insert to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85 N·m ((63 lb ft)) (3) Tighten the nuts to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section Water temperature regulator Opening temperature . . . . . . . . . . . . . . . . 77° to 81°C ((171° to 196°F)) Maximum open length of 11.5 mm (0.45276 inch) is achieved at the following temperature. . . . . . . . . . . . . . . . 130° C ((266° F)) i04335189 Water Pump Illustration 47 g02490498 Typical example (1) Tighten the setscrews to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 31 Specifications Section i04332590 Cylinder Block Bore in the cylinder block for the number 5 main bearings . . . . . . . . . . . . . . . . . . . . . . . 87.588 to 87.614 mm ((3.44834 to 3.44936 inch)) (5) Main bearing cap bolts Use the following procedure in order to install the main bearing cap bolts: 1. Apply clean engine oil to the threads of the main bearing cap bolts. 2. Put the main bearing caps in the correct position that is indicated by a number on the top of the main bearing cap.
UENR0622-02 Specifications Section i05955207 Crankshaft Illustration 49 g02841976 Typical example (1) Crankshaft gear (2) Crankshaft (3) Crankshaft thrust washers Maximum permissible temperature of the gear for installation on the crankshaft . . . . . 185° C ((365° F)) Maximum permissible temperature of the timing gear for the balancer (if equipped) for installation on the crankshaft . . . . . . . . . . . . . . . . . . . . 185° C ((365° F)) The end play of a new crankshaft . . . . . . . . 0.
UENR0622-02 33 Specifications Section Illustration 50 g02841978 Typical example (4) Journal 1 (5) Journal 2 (6) Journal 3 (7) Journal 4 Refer to table 4 for the run out of the crankshaft journals. Table 4 Journal Run out of the Journals (1) Mounting (2) 0.03 mm (0.00118 inch) (3) 0.03 mm (0.00118 inch) (4) 0.03 mm (0.00118 inch) (5) Mounting Inspect the crankshaft for wear or for damage.
UENR0622-02 Specifications Section Surface finish of connecting rod bearing journals . . . . . . . . . . . . . . . . . . . . . . Ra 0.3 microns maximum Width of the main bearing shells . . . . . 26.32 to 26.58 mm ((1.03622 to 1.04645 inch)) Surface finish of radii . . . . Ra 0.3 microns maximum Clearance between the bearing shell and the main bearing journals . . . . . 0.032 to 0.102 mm ((0.00126 to 0.00402 inch)) i04332763 Main Bearing Journal The original size of the main bearing journal . . .
UENR0622-02 35 Specifications Section i04479212 Connecting Rod Illustration 52 g02844317 Typical example (A) Class of weight (B) Part number (C) Date of production (DD/MM) (D) Date of production (Year) (E) Serial number markings on the connecting rod and connecting rod cap Illustration 51 g02859356 Typical example (1) The bearing shell for the connecting rod For the correct procedure to install the bearing shell for the connecting rod, refer to Disassembly and Assembly, “Pistons and Connecting Rods
UENR0622-02 Specifications Section i04332709 Piston and Rings Illustration 54 g01155119 Typical example (1) Top compression ring Illustration 53 g02859357 Typical example (3) Diameter of the finished bore for the piston pin . . . . . 36.01 to 36.02 mm ((1.41771 to 1.41811 inch)) (4) Distance between the parent bores . . . . . . 219.05 to 219.1 mm ((8.6240 to 8.6260 inch)) (5) Diameter for the finished bore for the connecting rod bearing . . . 67.833 to 67.848 mm ((2.67059 to 2.
UENR0622-02 37 Specifications Section Width of oil control ring . .2.470 to 2.490 mm ((0.09724 to 0.09803 inch)) Width of top groove in the piston . . . . . . . . . . . . . . . . . . . . . . 2.21 mm ((0.08701 inch)) The clearance between a new oil control ring and the groove in a new piston . . . 0.015 to 0.05 mm ((0.00059 to 0.00197 inch)) Ring gap . .0.050 to 0.090 mm ((0.00197 to 0.00354 inch)) Width of second groove in new piston . . . . . . . 2.05 to 2.07 mm ((0.08071 to 0.
UENR0622-02 Specifications Section i04335149 Piston Cooling Jet Alignment Piston Cooling Jet Illustration 57 g01352578 (2) Piston cooling jet (3) Rod (4) Cylinder block Illustration 56 g02490436 Typical example (1) Tighten the bolt to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 N·m ((13 lb ft)) Use the following procedure in order to check the alignment of the piston cooling jet. 1. Insert rod (3) into the end of the piston cooling jet (2).
UENR0622-02 39 Specifications Section i04555081 Balancer Illustration 58 i05240669 Front Housing and Covers g02727673 Typical example Tighten the bolts in the sequence that is shown in illustration 58 to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70 N·m ((52 lb ft)) Backlash values Illustration 59 g02909257 Typical example Backlash between the balancer gears . .0.075 to 0.165 mm ((0.00295 to 0.
UENR0622-02 Specifications Section Illustration 60 g02951436 Illustration 62 g02727967 Typical example Typical example (1) Tighten the setscrews in the sequence that is shown in illustration 60 to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 N·m ((18 lb ft)) (2) Tighten the setscrews for the front cover in the sequence that is shown in illustration 62 to the following torque. . . . . . . . . . . . . . . .
UENR0622-02 41 Specifications Section i05240675 Gear Group (Front) Clearance of idler gear bearing on hub . . 0.015 to 0.125 mm ((0.00059 to 0.00492 inch)) The end play of the idler gear . . . . 0.3 to 0.483 mm ((0.01181 to 0.01902 inch)) Number of teeth . . . . . . . . . . . . . . . . . . . . . . . . 31 (4) Camshaft gear Torque for the bolts for the camshaft gear . . . . . . . . . . . . . . . . . . . . . . . . . . 25 N·m ((18 lb ft)) Number of teeth . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section Backlash between the idler gear (2) and the accessory drive gear (if equipped) (3) . . . . 0.07 to 0.17 mm ((0.00276 to 0.00669 inch)) i04346169 Flywheel Backlash between the idler gear (2) and the camshaft gear (4) . . . . 0.07 to 0.17 mm ((0.00276 to 0.00669 inch)) Backlash between the camshaft gear (4) and the crankshaft gear (5) . . . . 0.07 to 0.17 mm ((0.00276 to 0.00669 inch)) Backlash between the crankshaft gear (5) and the oil pump idler gear (6) . . . .
UENR0622-02 43 Specifications Section i04346112 Flywheel Housing Tighten setscrews (1), (2), (3), (4), (5), (6), (7) and (8) in the sequence that is shown in illustration 66 to a final torque. . . . . . . . . . . . . . . . . . . 110 N·m ((81 lb ft)) Tighten setscrews (9) and (10) in the sequence that is shown in illustration 66 to a final torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section i05240730 Crankshaft Pulley Illustration 67 i05240729 Fan Drive g02501059 Illustration 68 g02844797 Typical example Typical example (1) Tighten the bolts to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 N·m ((33 lb ft)) (1) Tighten the bolts that secure the fan drive to the engine to the following torque. . . . . 25 N·m ((18 lb ft)) (2) Tighten the fasteners for the fan support to the following torque. . . . . . . . . .
UENR0622-02 45 Specifications Section i05240694 Engine Lifting Bracket Illustration 71 g03342585 Typical example (3) Tighten the bolts on the rear engine lifting brackets to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110 N·m ((81 lb ft)) Illustration 69 i05282770 g02488718 Typical example Alternator (1) Tighten the bolts on the front engine lifting bracket to the following torque. . . . . . . . . . .
UENR0622-02 Specifications Section 12V Alternator Illustration 72 12V Alternator g03357091 Illustration 73 Typical example Typical example (1) Terminal “D+” (3) Terminal “W” (3) Terminal “W” (2) Terminal “B+” Tighten the nut on the terminal to the following torque. . . . . . . . . . . . . . . . . . . . 11 N·m ((97 lb in)) Tighten the nut for the alternator pulley to the following torque. . . . . . . . . . . . . . . . 50 N·m ((37 lb ft)) Output The output of the alternator . . . . . . . . . .
UENR0622-02 47 Specifications Section 12V Alternators 24V Alternator Illustration 75 g02620019 Typical example (3) Terminal “W” (1) Terminal “B+” Illustration 74 g03357160 Typical example (1) Terminal “W” (2) Terminal “D+” (3) Terminal “B+” Tighten the nut on the terminal to the following torque. . . . . . . . . . . . . . . . 7.75 N·m ((68.60 lb in)) Tighten the nut for the alternator pulley to the following torque. . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section 12 V Starting Motor 3.2 kW (1) Tighten the positive terminal nut to the following torque. . . . . . . . . . . . . . . . . . . . . . . . 15 N·m ((11 lb ft)) (2) Tighten the solenoid terminal to the following torque. . . . . . . . . . . . . . . . . . . . . . . . 15 N·m ((11 lb ft)) (3) Tighten the negative terminal nut to the following torque. . . . . . . . . . . . . . . . . . . . . . . . 18 N·m ((13 lb ft)) 24 V Starting Motor 4.
UENR0622-02 49 Specifications Section i04346352 Coolant Temperature Sensor i05246996 Boost Pressure Sensor (If equipped) Illustration 79 g02621136 Typical example (1) Tighten the coolant temperature sensor to the following torque. . . . . . . . . . . . . . . . 25 N·m ((18 lb ft)) Illustration 80 g03344803 Typical example Illustration 81 g03344804 Typical example (1) Tighten the fastener to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section (2) Tighten the fastener to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 N·m ((89 lb in)) (3) Tighten the sensor to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 N·m ((89 lb in)) i04555069 Oxygen Sensor (4) Tighten the fastener to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 51 Specifications Section i05246995 i04550539 Inlet Manifold Temperature Sensor (If equipped) Inlet Manifold Temperature and Pressure Sensor (If equipped) Illustration 83 Illustration 84 g03344802 g02722054 Typical example Typical example Tighten the sensor to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 N·m ((11 lb ft)) (1) Tighten the screw for the inlet manifold air pressure and temperature sensor to the following torque. . . . . . . . . . .
UENR0622-02 Specifications Section i04550469 Temperature Sensor (DPF Inlet) Illustration 85 i04550534 Temperature Sensor (DOC Inlet) g02722006 Illustration 86 g02722047 Typical example Typical example (1) Tighten the temperature sensor to the following torque. . . . . . . . . . . . . . . . . . . . . . . . 45 N·m ((33 lb ft)) (1) Tighten the temperature sensor to the following torque. . . . . . . . . . . . . . . . . . . . . . . . 45 N·m ((33 lb ft)) This document has been printed from SPI2.
UENR0622-02 53 Specifications Section i05240876 Pressure Sensor (NOx Reduction System) Illustration 88 g03342627 Typical example Illustration 87 Typical example g02724012 (1) Tighten the fastener to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 N·m ((11 lb ft)) (2) Tighten the sensor to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 N·m ((11 lb ft)) This document has been printed from SPI2.
UENR0622-02 Specifications Section i05240937 Operating voltage . . . . . . . . . . . . . . . . . . . . . . . 5 VDC Temperature Sensor (NOx Reduction System) Illustration 89 g03342646 Typical example Illustration 90 g02722380 Typical example (1) Tighten the sensor to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45 N·m ((33 lb ft)) This document has been printed from SPI2.
UENR0622-02 Specifications Section i05239559 Speed/Timing Sensor (2) Tighten the screw for the camshaft position sensor to the following torque. . . . 10 N·m ((89 lb in)) i05241792 Electronic Control Module Tighten the M6 fasteners to the following torque . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
UENR0622-02 Specifications Section i04425773 Glow Plugs Illustration 93 g02621690 Typical example (1) Tighten the glow plugs to the following torque. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 N·m ((80 lb in)) This document has been printed from SPI2.
UENR0622-02 Index Section Index A G Alternator ...........................................................45 12V Alternator..................................................46 12V Alternators ................................................47 24V Alternator..................................................47 Gear Group (Front)..............................................41 Glow Plugs .........................................................56 B Balancer............................................
UENR0622-02 Index Section W Water Pump........................................................30 Water Temperature Regulator and Housing...........29 This document has been printed from SPI2.
This document has been printed from SPI2.
UENR0622 ©2016 Perkins Engines Company Limited All Rights Reserved 60 June 2016 This document has been printed from SPI2.
