Installation Guide

ManualsBrandsPergo ManualsLaminate FlooringLF000906

PERGO Timbercraft + WetProtect Floor Install Instructions

Tools Required for Installation

Common Tools

Wood

Glue

Carbide

40T Blade

Other Tools and Supplies

(

)

PREMIUM

SYSTEM

COMPONENT

Finishing

Putty

PREMIUM

SYSTEM

COMPONENT

Finishing

Putty

SILICONE

CAULK

SILICONE

CAULK

SILICONE

CAULK

100% Silicone

Sealant

Felt furniture

pads

Moisture

Meter

Non Destructive Moisture

dlfwej dtra

djflsv

dlfwe vtra

alskdjf

vmwjc

Concrete

Encounter

Plus

100

150

200

250

Moisture

Meter

Laminate ﬂ oor tapping

block and 5mm (

/16")

spacers

10' (3 m)

> 5" (130 mm)

6 mil (0.15 mm) virgin

polyethelene vapor barrier

ground

> 8" (200 mm)

Job Site

Site Requirements

Laminate is a durable ﬂ oor covering, not intended as

structural material. Laminate requires a clean, dry, secure

subﬂ oor that meets building codes.

Laminate ﬂ oor is suitable for use in climate controlled (35-

65% RH and 60-85° F) indoor installations only and should

not be installed in rooms with ﬂ oor drains or sump pumps.

Laminate ﬂ oor can be installed above, on or below grade.

A moisture test is strongly recommended to determine if

high moisture exists in the subﬂ oor. When using a calcium

chloride moisture test for concrete subﬂ oors (ASTM 1869),

values must be ≤ 5 lbs/1000ft²/24-hr or <80% with an in situ

probe (ASTM F2170). Moisture readings of wood subﬂ oors

must be ≤ 12%.

Acceptable job site conditions, including relative humidity

and subﬂ oor moisture conditions, must be maintained

throughout the lifetime of the ﬂ ooring.

Laminate ﬂ ooring is installed as a ﬂ oating ﬂ oor and requires

the use of T-moldings in doorways 4 ft (1.22m) or less and

in rooms 40 feet (12.2 m) or larger in length or width. Floor

movement must not be constrained by glue, nails, screws,

hardware or other ﬁ xed obstructions.

This product must be installed in accordance with these

installation instructions.

For more information, call 1-800-33-PERGO

PE Foam

Backer Rod

2017_09_TMP_LOW

Summary of content (12 pages)

PAGE 1
PERGO Timbercraft + WetProtect Floor Install Instructions Tools Required for Installation Other Tools and Supplies Finishing Putty AL LY DEVEL O ers PE M AD 3 2 1 dlfwej dtra djflsv 4 5 6 0 50 0 100 150 Concrete Encounter Plus 200 250 dlfwe vtra alskdjf vmwjc D FOR LA IUM PREM IUM EM PREM SYST EM ENT SYST PON ENT COM PON COM TE FL O IN A O ac 5m m s I cer 5m m M Sp NG SPE C Spa Wood Glue RI Common Tools S E IN THE U Moisture Meter A 1 FL OZ (33.
PAGE 2
PERGO Timbercraft + WetProtect Floor Install Instructions Site and Material Preparation A B Wallbase Door Frame Casing Cutting Line E D C 1 inch (2,5 cm) % 48 hours F 60° – 85° F 15° – 29° C 35% – 65% RH H G > 8" (200 mm) subfloor 6 mil (0.15 mm) virgin polyethelene vapor barrier Site and Material Preparation A) Remove carpet and padding. Also remove any wood flooring installed on concrete. Do not remove products unless they are asbestos-free. B) Undercut door frame and wallbase.
PAGE 3
PERGO Timbercraft + WetProtect Floor Install Instructions 1 3 2 5 4 6 Left 2 6 Right 1 5 3 4 5 6 6 5 > 12 in > 30 cm 7 9 8 3 4 1 2 10 14 11 15 13 12 16 17 WOOD GLUE 3 2017_09_TMP_LOW
PAGE 4
PERGO Timbercraft + WetProtect Floor Install Instructions 18 19 Molding Silicone sealant Molding PE foam backer rod PE foam backer rod Silicone sealant Silicone sealant Flooring Installation 1. Inspect each plank. Floor should be installed blending planks from several cartons at the same time to ensure good color and shade mixture throughout the installation. 2. For the first row along straight walls, remove the tongue on all long side joints and on the short side of the 1st plank only. 3.
PAGE 5
PERGO Timbercraft + WetProtect Floor Install Instructions A B C Care and Cleaning A) Place felt floor protectors under legs of moveable furniture. Chair casters should be rubber – not plastic or metal. B) Place walk-off mats at entrances. C) Place felt floor protectors under legs of moveable furniture. Chair casters should be rubber – not plastic or metal. Place walk-off mats at entrances. Dust mop as primary cleaning method.
PAGE 6
PERGO Timbercraft + WetProtect Laminate Flooring on Wall Install Instructions Although originally designed as a durable floor covering, many consumers have started using Pergo laminate flooring on walls to give their rooms more character and to create a feature or accent wall. Laminate can be utilized as a decorative covering over an existing clean, dry, secure and vertical wall that meets building codes. The wall substrate should be primed or painted drywall (gypsum board) only.
PAGE 7
PERGO Timbercraft + WetProtect Vertical Wainscot Style Wall Install Instructions 1. Measure the length of your laminate plank and the length of the wall area to determine the total square footage area. Order that amount of flooring plus an additional 10% for incorrect cuts. 2. Remove all base and trim from accent wall. Measure from the floor a distance equal to your laminate plank plus one inch then level and mark the wall with a chalk line. With an electronic stud finder locate and mark wall studs.
PAGE 8
PERGO Timbercraft + WetProtect Vertical Wainscot Style Wall Install Instructions 8. Apply silicone adhesive to the back side of the plank in an “S” pattern. If you’re using a laminate plank with an attached pad, apply the silicone directly to the pad on the back of the plank. (Figure 3) 9. Adhere the plank to the wall leaving a 3/16" gap (A) from the corners of the wall and a 1" gap (B) at bottom. Drive brad nails ½" from the top and bottom of each plank to secure to wall.
PAGE 9
PERGO Timbercraft + WetProtect Horizontal Accent Wall Install Instructions 1. Measure the length and width of the wall area to determine the total square footage area. Order that amount of flooring plus an additional 10% for incorrect cuts. 2. Remove baseboards from the accent wall and locate the wall studs using the stud finder tool. Mark vertical lines over all studs. Use painters tape to extend stud location to ceiling if needed. (Figure 1) 3.
PAGE 10
PERGO Timbercraft + WetProtect Horizontal Accent Wall Install Instructions 9. Drive a brad nail into each plank at each wall stud through the shallow area of the extended groove (see inset diagram). Take care that the brad nail heads are not raised, but also don’t force them all the way through the groove. This will allow easy connection of the next row of planks.
PAGE 11
PERGO Timbercraft + WetProtect Horizontal Accent Wall Install Instructions 13. Repeat this process for each plank working your way up to the last row. (Figure 8) 14. For the last row of the installation, use painters tape to mark the stud location for brad nailing. Cut all planks in the last row to the required width to complete the installation. Complete the installation as you have the earlier rows. (Figure 8a) 15. Use quarter round for inside corners and ceiling.
PAGE 12
PERGO Timbercraft + WetProtect Laminate Flooring on Wall Install Instructions Care and Cleaning Dry wipe as primary cleaning method. Occasionally damp wipe with water only. NO wet washing. If needed, use 1 cup of vinegar per gallon of water OR 1/3 cup non-sudsing ammonia per gallon of water. DO NOT use detergents, abrasive cleaners, soaps, waxes or polishes. Wipe off spills immediately. DO NOT allow moisture to remain on the product surface for longer than 30 minutes.