Data Sheet
AV6301 Datasheet (Preliminary) revision 0.2
CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 15 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA
3.4 Electrical Characteristics – RF Receiver
Operating Conditions: VDC = 4.4V to 5.5V, VDDIO = 3.3V, T
A
= 0ºC to +70 ºC; RF Channel Freq = 2403.35-2477.35MHz, measured at
the single-ended input of the RF balun (with external impedance matching). Typical specifications at T
A
= 25ºC, VDC = 5.0V.
Table 3-4 AV6301 Electrical Characteristics - RF Receiver
PARAMETER CONDITIONS MIN TYP MAX UNIT
RF Channel Frequency Range LO frequency (driving the mixers)
RF carrier frequency
2402
2403.35
2478
2479.35
MHz
MHz
Modulated Signal Offset from LO 1.35 MHz
Sensitivity (Note 1) T
A
=25ºC, LNA = High gain mode; max IF gain -89 dBm
Max input signal (desired signal) (Note 1) T
A
=25ºC, LNA = low gain mode; min IF gain -5 dBm
Input Blocker Level – High Gain mode > 2MHz offset -45 dBm
Out-of-band blocker level <2400 MHz; >2483.5 MHz TBD dBm
Spurious RF outputs
<2400 MHz
>2483.5 MHz
-75
-75
dBm
dBm
Note 1: Sensitivity and max signal level are defined as the onset of 0.2% Block Error Rate. )BLER)
3.5 Electrical Characteristics – RF Transmitter
Operating Conditions: VDC = 4.4V to 5.5V, VDDIO = 3.3V, T
A
= 0ºC to +70 ºC; RF Channel Freq = 2403.35-2477.35MHz, measured at
the single-ended input of the RF balun (with external impedance matching). Typical specifications at T
A
= 25ºC, VDC = 5.0V.
Table 3-5 AV6301 Electrical Characteristics - RF Transmitter
PARAMETER CONDITIONS MIN TYP MAX UNIT
RF Channel Frequency Range LO frequency (driving the mixers)
RF carrier frequency
2402
2403.35
2478
2479.35
MHz
MHz
Modulated Signal Offset from LO 1.35 MHz
Modulated Signal Bandwidth -10dB point 1.8 MHz
Output Power Pi/4 DQPSK modulated signal
ACPR: Adj <
-23dBc, Alt < -30dBc
+2
dBm
Output harmonics 2
nd
harmonic, P
out
= 0dBm
3
rd
harmonic, P
out
= 0dBm
-52
-50
dBm
dBm
Out-of-band Spurious Output RF < 2390MHz, > 2483.5MHz, 1MHz RBW <-62 dBm
Output Noise Floor RF < 2390MHz, > 2483.5MHz, 1MHz RBW <-62 dBm
3.6 Electrical Characteristics – End-to-end Audio Characteristics
Operating Conditions: VDC = 4.4V to 5.5V or VIN = 3.2V to 4.3V, VDDIO = 3.3V, TA = 0ºC to +70 ºC; Typical specifications at TA = 25ºC,
VDC = 5.0V.
Table 3-6 AV6301 Electrical Characteristics - End-to-End Audio Characteristics
PARAMETER CONDITIONS MIN TYP MAX UNITS
SNR Forward stereo path 93 dB
Reverse mono path 68 dB
Audio/Voice Bandwidth End-to-end audio BW; 0.1dB point 20 kHz
End-to-end audio BW; 0.1dB point 6.5 kHz
Audio Latency
AV6201 USB to AV6202 analog output
AV6201 I2S to AV6202 I2S output
<16
<16
msec
msec
Voice Latency AV6202 analog input to AV6201 USB output <16 msec