T20 KINETIC LOG SPLITTER Instruction & Assembly Manual Patent Pending Assembly and troubleshooting video at www.ytlinternational.
Table of Contents General Warnings and Rules…………………………………………………….3 Hazard Signal Word Definitions………………………………………………….4 Assembly Instructions…………………………………………………………5-11 Kinetic Splitter General Instructions……………………………………………12 Operation Instructions………………………………………………………12-14 Maintenance and Storage…………………………………………………15 Troubleshooting………………………………………………………………….16 Specifications…………………………………………………………………….17 Parts Drawing & Parts List…………………………………………………..
GENERAL WARNINGS READ and UNDERSTAND this manual completely before using T20 0 Log Splitter. Operator must read and understand nderstand all safety and warning information, operating instructions, maintenance and storage instructions before operating this equipment.. Failure to properly operate and maintain the log splitter could result in serious injury to the the operator or bystanders. bystanders Operation Warnings Do not at any time carry passengers, sit or stand on the log splitter.
Hazard Signal Word Definitions This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. DANGER DANGER indicates an imminently hazardou hazardous situation which, if not avoided, will result in death or serious injury. WARNING WARNING indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
WARNING Read and follow all instructions for assembly and operation. Failure to properly assemble this equipment could result in serious injury to the user or bystanders, or cause equipment damage. Engine Shipped Without Oil. Before starting engine, fill with SAE 10W-30 motor oil. See engine manual for engine oil capacity. Inspect all Log Splitter Components. If you have damaged components: Contact the freight company that delivered the log splitter and file a claim.
STEP 2: Attach the Front Support Leg to the Beam 1. Attach the front support leg to the beam using hex bolt M10x30(x4), flat washerØ10(x4), lock washerØ10(x4) and nylon lock nut M10(x4). Tighten all hardware. RECOMMEND Use a shop crane or hoist to lift and position the beam. STEP 3: Attach Beam to the Axle Assembly 1. Attach the beam assembly to the axle assembly using hex bolt M10x50(x4), large flat washerØ10(x8), elastic cushion(x4),lock washer Ø10(x4) and nylon lock nut M10(x4).
STEP 4: Mount Engine and Connecting Belts 1. Insert the engine assembly into slot, push the engine forward and install square nut(x1) and nylon lock nut M10(x1). 2. Work the belts onto the grooves on engine clutch, ensuring belts stay in corresponding grooves on fly wheels. 3. Put on engine position bolt(x1), adjust the belt tension by pushing down on the belt to ensure the dent is less than 0.4inch.Once the belt tension is correct, lock engine position bolt in place.
STEP 6: Attach the Left Side of the Worktable Note: Leave all bolts loose for steps 6, 7 and 8, then tighten all bolts once all parts are installed. 1. Attach log cradle and left side of the worktable to the beam using hex bolt M10x30(x3), flat washer Ø10(x3) and lock washer Ø10(x3), see figure shown below. STEP 7: Attach the Right Side of the Worktable 1.
STEP 8: Connect the Right and Left Sides of the Worktable 1. Fix the worktables to the front bracket using inner hex round head screw M10x25(x5), flat washer Ø10(x5), lock washerØ10(x5) and nylon lock nut M10(x5). 2. Connect the right and left sides of the worktable using the table-board connecting plate(x1), inner hex countersunk head screw M8x20(x4), flat washer Ø8(x4) and nylon lock nut M8(x4), ensuring the oval holes at the table-board connecting plate is upward. 3.
STEP 10: Attach Outer Housing Note: Leave all inner hex round head screws loose until the parts are installed in steps 10 and 11. 1. Attach threaded rod into the holes in the wheel stand and tighten. 2. Attach outer housing using inner hex round head screw M6x20(x4), lock washer Ø6(x4) and large flat washer Ø6(x4). STEP 11: Attach the End Cover and Handle 1. Attach the end cover to the beam using inner hex round head screw M6x20(x2), lock washer Ø6(x2) and large flat washer Ø6(x2). 2.
STEP 12: Add Engine Oil 1. 2. 3. 4. Make sure the log splitter is on a level surface. Remove oil fill cap/dipstick to add oil. Refer to the separate owner’s engine manual for oil capacity; replace oil fill cap/dipstick. Check engine oil level daily and add as needed. NOTE: During the break-in period check the engine oil level often. CAUTION DO NOT attempt to crank or start the engine before it has been properly filled with the recommended type and amount of oil.
Kinetic Splitter General Information 1. Break in period - Break in period for the kinetic splitter is 500 cycles. 2. Principle of operation - This unit is designed to outperform the traditional hydraulic 20ton log splitter. Splitting power is derived from 1 spinning fly wheel. When actuation handle is moved to split position, the rotational energy stored in flywheel is converted to splitting force. This unit is fast and powerful.
USING YOUR LOG SPLITTER 1. 2. 3. 4. 5. 6. 7. 8. Start engine using instructions from engine manual. Advance throttle control maximum speed. Grab log by sides and place onto rails against wedge. Push the safety handle down and move the control handle to the SPLIT position to initiate cycle, release handle and the push plate will retract. Push plate automatically retracts at end of stroke. To retract the push plate before end of stroke, return lever to RETRACT position.
11. Always wear safety gear, eye protection, gloves and work boots when operating the log splitter. 12. Start the engine and make sure the log splitter is on level ground before operating. 13. Make sure hands are clear from the wedge and crush hazard areas. CRUSH WARNING Wedge can cut through skin and break bones. Keep both hands away from wedge and beam slide. Serious accidents can happen when other people are allowed inside the work zone.
Maintenance and Storage Regular maintenance is the way to ensure the best performance and long life of your machine. Please refer to this manual and the engine manufacturer's owner's manual for maintenance procedures. Service intervals listed in the checklist below supersede those listed in the engine manufacturer's owner's manual. WARNING Before performing any maintenance procedure or inspection, stop the engine, wait five (5) minutes to allow all parts to cool.
Troubleshooting No. Problem Cause Solution Engine will not start 1. Check gas level 2. Check oil level 3. Check fuel ON/OFF 4. Check ON/OFF switch 1.Wood Chips or Debris under push plate 2. Retract spring too loose. 1. Add gasoline 2. Add oil 3. Reference engine manual 1 2 Push plate cannot retract or retracts slowly Retract spring too tight. 3 Push plate retract too fast No force or little force during splitting 1. #57 Round Nut M40x1.5 is loose 2. Clutch spring deformed 4 1.
Specifications Cycle Time .................................................................................................... 4 Sec Wedge .................................................................................. 6.3” Hardened Steel Max. Log Length ............................................................................................ 20.3” Wheel Size ...........................................................................................16” / 4.80-8 Working Height..........................
Parts Drawing & Parts List - 18 -
Parts Drawing & Parts List Ref# 1 Drawing No. LSF2000-00001 Description Right Worktable Qty 1 2 911608020 Inner Hex Countersunk Head Screw M8X20 4 3 LSF3000-00001 Table-Board Connecting Plate 1 4 9301-08000-DX Flat Washer Ø8 8 5 9206-08000 Nylon Lock Nut M8 10 6 9301-10000-DX Flat Washer Ø10 22 7 9206-01000 Nylon Lock Nut M10 24 8 LSF2000-00002 Front Bracket 1 9 9306-10000DX Lock Washer Ø10 32 10 LSF2000-00003 Log Cradle 2 11 LSF2000-01000 Beam 1 12 9101-10030-8.
Parts Drawing & Parts List Ref# 36 Drawing No.
Parts Drawing & Parts List Ref# 71 Drawing No. LSF2000-08000 Description Sliding Block Qty 1 72 LSF2000-00049 Adjustable Washer 1 73 LSF2000-00024FH Connecting Rod 1 74 LSF2000-00031 Elastic Cushion 4 75 LSF2000-12000 Wheel Stand 1 76 9101-10050-DX Hex Bolt M10x50 4 77 9302-10000-DX Large Lock Washer Ø10 (28x11x3) 8 78 LSF2000-00020 Action Handle 1 79 LSF2000-00019 Right Press Plate 1 80 LSF2000-00032 Left Worktable 1 81 9104-10025-8.
Parts Drawing & Parts List Ref# 106 Drawing No. LSF2000-00033 Description Clutch 60-2A Qty 1 107 9101-1290-8.8DX Engine Position Bolt 1 108 LSF3000-00029 Square Nut 1 109 LSF3000-09000 Engine Base 1 110 8801-4.78*4.78*50 Flat Key 4.78x4.78x50 1 111 9701-A1727 A-1727 Belt 2 Engine 1 112 113 9112-10030-8.8FH Inner Hex ScrewM10x30 1 114 LSF2000-00035 Elastic Bar 1 115 LSF2000-00034 Reset Tension Spring 2 116 LSF2000-00036 End Cover 1 117 9105-12030-8.
Limited Warranty Warranty For 2 years from the date of purchase YTL International will replace or repair defects in material and workmanship for the original purchaser of the log splitter for Residential use only, AND 90 days for Commercial use. For 2 years the engine residential warranty is covered per the engine manufactures warranty. For 1 year from date of purchase YTL International will repair or replace internal system components.
