User's Manual

ManualsBrandsPEPWAVE ManualsElectronicsPEPWAVE / peplink Wireless Product

160

161

162

163

164

165

166

167

168

169

Table Of Contents

Introduction and Scope
Glossary
1 Product Features
- 1.1 Supported Network Features
- 1.2 Other Supported Features
2 Overview
- 2.1 MAXAdapter
- 2.2 Drop-in Mode and LAN Bypass: Transparent Deployment
- 2.3 QoS: Clearer VoIP
- 2.4 Per-User Bandwidth Control
- 2.5 High Availability via VRRP
- 2.6 USB Modem and Android Tethering
- 2.7 Built-In Remote User VPN Support
- 2.8 SIM-card USSD support
- 2.9 DPI Engine
3 Installation
- 3.1 Preparation
- 3.2 Constructing the Network
- 3.3 Configuring the Network Environment
4 Connecting to the Web Admin Interface
5 SpeedFusion Cloud
- 5.1 Activate SpeedFusion Cloud Service
- 5.2 Enable SpeedFusion Cloud
- 5.3 Connect Clients to Cloud
- 5.4 Link Wi-Fi to Cloud
6 Configuring the LAN Interface(s)
- 6.1 Basic Settings
- 6.2 Port Settings
- 6.3 Captive Portal
7 Configuring the WAN Interface(s)
- 7.1 Ethernet WAN
- 7.2 Cellular WAN
- 7.3 Wi-Fi WAN
  - 7.3.1 Creating Wi-Fi Connection Profiles
- 7.4 WAN Health Check
- 7.5 Dynamic DNS Settings
8 Advanced Wi-Fi Settings
9 ContentHub Configuration
- 9.1 ContentHub
- 9.2 Configuring the ContentHub
- 9.3 Configure a website to be published from the ContentHub
- 9.4 Configure an application to be published from the ContentHub
10 MediaFast Configuration
- 10.1 Setting Up MediaFast Content Caching
- 10.2 Scheduling Content Prefetching
- 10.3 Viewing MediaFast Statistics
11 Bandwidth Bonding SpeedFusionTM / PepVPN
- 11.1 PepVPN
- 11.2 The Pepwave Router Behind a NAT Router
12 IPsec VPN
- 12.1 IPsec VPN Settings
13 Outbound Policy Management
- 13.1 Outbound Policy
- 13.2 Custom Rules for Outbound Policy
14 Inbound Access
- 14.1 Port Forwarding Service
  - 14.1.1 UPnP / NAT-PMP Settings
15 NAT Mappings
16
- 16.1 User Groups
- 16.2 Bandwidth Control
- 16.3 Application
17 Firewall
- 17.1 Outbound and Inbound Firewall Rules
- 17.2 Content Blocking
- 18 OSPF & RIPv2
- 19 BGP
20 Remote User Access
- 20.1 L2TP with IPsec
- 20.2 OpenVPN
- 20.3 PPTP
- 20.4 Authentication Methods
21 Miscellaneous Settings
- 21.1 High Availability
- 21.2 Certificate Manager
- 21.3 Service Forwarding
- 21.4 Service Passthrough
- 21.5 UART
- 21.6 GPS Forwarding
- 21.7 Ignition Sensing
  - Ignition Sensing installation
  - GPIO Menu
- 21.8 NTP Server
- 21.9 Grouped Networks
- 21.10 SIM Toolkit
22 AP - access point
- 23 AP Controller
- 23.1 Wireless SSID
- 23.2 Settings
24 AP Controller Status
- 24.1 Info
- 24.2 Access Point (Usage)
- 24.3 Wireless SSID
- 24.4 Wireless Client
- 24.5 Nearby Device

https://www.peplink.com

160

Wi-Fi Radio Settings

Operating

Country

This option sets the country whose regulations the Pepwave router follows.

Wi-Fi Antenna

Choose from the router's internal or optional external antennas, if so equipped.

Important Note

Per FCC regulations, the country selection is not available on all models marketed in the US. All US

models are fixed to US channels only.

Wi-Fi AP Settings

Protocol

This option allows you to specify whether 802.11b and/or 802.11g client

association requests will be accepted. Available options are 802.11ng and

802.11na. By default, 802.11ng is selected.

Channel

This option allows you to select which 802.11 RF channel will be used. Channel

1 (2.412 GHz) is selected by default.

Channel Width

Auto (20/40 MHz) and 20 MHz are available. The default setting is Auto (20/40

MHz), which allows both widths to be used simultaneously.

Output Power

This option is for specifying the transmission output power for the Wi-Fi AP.

There are 4 relative power levels available – Max, High, Mid, and Low. The

actual output power will be bound by the regulatory limits of the selected country.

Beacon Rate

This option is for setting the transmit bit rate for sending a beacon. By default,

1Mbps is selected.