User's Manual

ManualsBrandsPEPWAVE ManualsElectronicsPEPWAVE / peplink Wireless Product

121

122

123

124

125

126

127

128

129

130

Table Of Contents

Introduction and Scope
Glossary
1 Product Features
- 1.1 Supported Network Features
- 1.2 Other Supported Features
2 Overview
- 2.1 MAXAdapter
- 2.2 Drop-in Mode and LAN Bypass: Transparent Deployment
- 2.3 QoS: Clearer VoIP
- 2.4 Per-User Bandwidth Control
- 2.5 High Availability via VRRP
- 2.6 USB Modem and Android Tethering
- 2.7 Built-In Remote User VPN Support
- 2.8 SIM-card USSD support
- 2.9 DPI Engine
3 Installation
- 3.1 Preparation
- 3.2 Constructing the Network
- 3.3 Configuring the Network Environment
4 Connecting to the Web Admin Interface
5 SpeedFusion Cloud
- 5.1 Activate SpeedFusion Cloud Service
- 5.2 Enable SpeedFusion Cloud
- 5.3 Connect Clients to Cloud
- 5.4 Link Wi-Fi to Cloud
6 Configuring the LAN Interface(s)
- 6.1 Basic Settings
- 6.2 Port Settings
- 6.3 Captive Portal
7 Configuring the WAN Interface(s)
- 7.1 Ethernet WAN
- 7.2 Cellular WAN
- 7.3 Wi-Fi WAN
  - 7.3.1 Creating Wi-Fi Connection Profiles
- 7.4 WAN Health Check
- 7.5 Dynamic DNS Settings
8 Advanced Wi-Fi Settings
9 ContentHub Configuration
- 9.1 ContentHub
- 9.2 Configuring the ContentHub
- 9.3 Configure a website to be published from the ContentHub
- 9.4 Configure an application to be published from the ContentHub
10 MediaFast Configuration
- 10.1 Setting Up MediaFast Content Caching
- 10.2 Scheduling Content Prefetching
- 10.3 Viewing MediaFast Statistics
11 Bandwidth Bonding SpeedFusionTM / PepVPN
- 11.1 PepVPN
- 11.2 The Pepwave Router Behind a NAT Router
12 IPsec VPN
- 12.1 IPsec VPN Settings
13 Outbound Policy Management
- 13.1 Outbound Policy
- 13.2 Custom Rules for Outbound Policy
14 Inbound Access
- 14.1 Port Forwarding Service
  - 14.1.1 UPnP / NAT-PMP Settings
15 NAT Mappings
16
- 16.1 User Groups
- 16.2 Bandwidth Control
- 16.3 Application
17 Firewall
- 17.1 Outbound and Inbound Firewall Rules
- 17.2 Content Blocking
- 18 OSPF & RIPv2
- 19 BGP
20 Remote User Access
- 20.1 L2TP with IPsec
- 20.2 OpenVPN
- 20.3 PPTP
- 20.4 Authentication Methods
21 Miscellaneous Settings
- 21.1 High Availability
- 21.2 Certificate Manager
- 21.3 Service Forwarding
- 21.4 Service Passthrough
- 21.5 UART
- 21.6 GPS Forwarding
- 21.7 Ignition Sensing
  - Ignition Sensing installation
  - GPIO Menu
- 21.8 NTP Server
- 21.9 Grouped Networks
- 21.10 SIM Toolkit
22 AP - access point
- 23 AP Controller
- 23.1 Wireless SSID
- 23.2 Settings
24 AP Controller Status
- 24.1 Info
- 24.2 Access Point (Usage)
- 24.3 Wireless SSID
- 24.4 Wireless Client
- 24.5 Nearby Device

https://www.peplink.com

124

RIPv2 item on the sidebar to reach the following menu:

OSPF

Router ID

This field determines the ID of the router. By default, this is specified as the LAN IP

address. If you want to specify your own ID, enter it in the Custom field.

Area

This is an overview of the OSPFv2 areas you have defined. Click on the area name

to configure it. To set a new area, click Add. To delete an existing area, click .