User's Manual

ManualsBrandsPEPWAVE ManualsElectronicsPEPWAVE / peplink Wireless Product

Table Of Contents

Introduction and Scope
Glossary
1 Product Features
- 1.1 Supported Network Features
- 1.2 Other Supported Features
2 Overview
- 2.1 MAXAdapter
- 2.2 Drop-in Mode and LAN Bypass: Transparent Deployment
- 2.3 QoS: Clearer VoIP
- 2.4 Per-User Bandwidth Control
- 2.5 High Availability via VRRP
- 2.6 USB Modem and Android Tethering
- 2.7 Built-In Remote User VPN Support
- 2.8 SIM-card USSD support
- 2.9 DPI Engine
3 Installation
- 3.1 Preparation
- 3.2 Constructing the Network
- 3.3 Configuring the Network Environment
4 Connecting to the Web Admin Interface
5 SpeedFusion Cloud
- 5.1 Activate SpeedFusion Cloud Service
- 5.2 Enable SpeedFusion Cloud
- 5.3 Connect Clients to Cloud
- 5.4 Link Wi-Fi to Cloud
6 Configuring the LAN Interface(s)
- 6.1 Basic Settings
- 6.2 Port Settings
- 6.3 Captive Portal
7 Configuring the WAN Interface(s)
- 7.1 Ethernet WAN
- 7.2 Cellular WAN
- 7.3 Wi-Fi WAN
  - 7.3.1 Creating Wi-Fi Connection Profiles
- 7.4 WAN Health Check
- 7.5 Dynamic DNS Settings
8 Advanced Wi-Fi Settings
9 ContentHub Configuration
- 9.1 ContentHub
- 9.2 Configuring the ContentHub
- 9.3 Configure a website to be published from the ContentHub
- 9.4 Configure an application to be published from the ContentHub
10 MediaFast Configuration
- 10.1 Setting Up MediaFast Content Caching
- 10.2 Scheduling Content Prefetching
- 10.3 Viewing MediaFast Statistics
11 Bandwidth Bonding SpeedFusionTM / PepVPN
- 11.1 PepVPN
- 11.2 The Pepwave Router Behind a NAT Router
12 IPsec VPN
- 12.1 IPsec VPN Settings
13 Outbound Policy Management
- 13.1 Outbound Policy
- 13.2 Custom Rules for Outbound Policy
14 Inbound Access
- 14.1 Port Forwarding Service
  - 14.1.1 UPnP / NAT-PMP Settings
15 NAT Mappings
16
- 16.1 User Groups
- 16.2 Bandwidth Control
- 16.3 Application
17 Firewall
- 17.1 Outbound and Inbound Firewall Rules
- 17.2 Content Blocking
- 18 OSPF & RIPv2
- 19 BGP
20 Remote User Access
- 20.1 L2TP with IPsec
- 20.2 OpenVPN
- 20.3 PPTP
- 20.4 Authentication Methods
21 Miscellaneous Settings
- 21.1 High Availability
- 21.2 Certificate Manager
- 21.3 Service Forwarding
- 21.4 Service Passthrough
- 21.5 UART
- 21.6 GPS Forwarding
- 21.7 Ignition Sensing
  - Ignition Sensing installation
  - GPIO Menu
- 21.8 NTP Server
- 21.9 Grouped Networks
- 21.10 SIM Toolkit
22 AP - access point
- 23 AP Controller
- 23.1 Wireless SSID
- 23.2 Settings
24 AP Controller Status
- 24.1 Info
- 24.2 Access Point (Usage)
- 24.3 Wireless SSID
- 24.4 Wireless Client
- 24.5 Nearby Device

https://www.peplink.com

1.1.2 LAN

● Wi-Fi AP

● Ethernet LAN ports

● DHCP server on LAN

● Extended DHCP option support

● Static routing rules

● VLAN on LAN support

1.1.3 VPN

● PepVPN with SpeedFusion

● PepVPN performance analyzer

● X.509 certificate support

● VPN load balancing and failover among selected WAN connections

● Bandwidth bonding and failover among selected WAN connections

● IPsec VPN for network-to-network connections (works with Cisco and Juniper only)

● Ability to route Internet traffic to a remote VPN peer

● Optional pre-shared key setting

● SpeedFusion

throughput, ping, and traceroute tests

● PPTP server

● PPTP and IPsec passthrough

1.1.4 Firewall

● Outbound (LAN to WAN) firewall rules

● Inbound (WAN to LAN) firewall rules per WAN connection

● Intrusion detection and prevention

● Specification of NAT mappings

● Outbound firewall rules can be defined by destination domain name

1.1.5 Captive Portal

● Splash screen of open networks, login page for secure networks

● Customizable built-in captive portal

● Supports linking to outside page for captive portal

1.1.6 Outbound Policy

● Link load distribution per TCP/UDP service

● Persistent routing for specified source and/or destination IP addresses per TCP/UDP