User's Manual

ManualsBrandsPEPWAVE ManualsElectronicsPEPWAVE / peplink Wireless Product

101

102

103

104

105

106

107

108

109

110

Table Of Contents

Introduction and Scope
Glossary
1 Product Features
- 1.1 Supported Network Features
- 1.2 Other Supported Features
2 Overview
- 2.1 MAXAdapter
- 2.2 Drop-in Mode and LAN Bypass: Transparent Deployment
- 2.3 QoS: Clearer VoIP
- 2.4 Per-User Bandwidth Control
- 2.5 High Availability via VRRP
- 2.6 USB Modem and Android Tethering
- 2.7 Built-In Remote User VPN Support
- 2.8 SIM-card USSD support
- 2.9 DPI Engine
3 Installation
- 3.1 Preparation
- 3.2 Constructing the Network
- 3.3 Configuring the Network Environment
4 Connecting to the Web Admin Interface
5 SpeedFusion Cloud
- 5.1 Activate SpeedFusion Cloud Service
- 5.2 Enable SpeedFusion Cloud
- 5.3 Connect Clients to Cloud
- 5.4 Link Wi-Fi to Cloud
6 Configuring the LAN Interface(s)
- 6.1 Basic Settings
- 6.2 Port Settings
- 6.3 Captive Portal
7 Configuring the WAN Interface(s)
- 7.1 Ethernet WAN
- 7.2 Cellular WAN
- 7.3 Wi-Fi WAN
  - 7.3.1 Creating Wi-Fi Connection Profiles
- 7.4 WAN Health Check
- 7.5 Dynamic DNS Settings
8 Advanced Wi-Fi Settings
9 ContentHub Configuration
- 9.1 ContentHub
- 9.2 Configuring the ContentHub
- 9.3 Configure a website to be published from the ContentHub
- 9.4 Configure an application to be published from the ContentHub
10 MediaFast Configuration
- 10.1 Setting Up MediaFast Content Caching
- 10.2 Scheduling Content Prefetching
- 10.3 Viewing MediaFast Statistics
11 Bandwidth Bonding SpeedFusionTM / PepVPN
- 11.1 PepVPN
- 11.2 The Pepwave Router Behind a NAT Router
12 IPsec VPN
- 12.1 IPsec VPN Settings
13 Outbound Policy Management
- 13.1 Outbound Policy
- 13.2 Custom Rules for Outbound Policy
14 Inbound Access
- 14.1 Port Forwarding Service
  - 14.1.1 UPnP / NAT-PMP Settings
15 NAT Mappings
16
- 16.1 User Groups
- 16.2 Bandwidth Control
- 16.3 Application
17 Firewall
- 17.1 Outbound and Inbound Firewall Rules
- 17.2 Content Blocking
- 18 OSPF & RIPv2
- 19 BGP
20 Remote User Access
- 20.1 L2TP with IPsec
- 20.2 OpenVPN
- 20.3 PPTP
- 20.4 Authentication Methods
21 Miscellaneous Settings
- 21.1 High Availability
- 21.2 Certificate Manager
- 21.3 Service Forwarding
- 21.4 Service Passthrough
- 21.5 UART
- 21.6 GPS Forwarding
- 21.7 Ignition Sensing
  - Ignition Sensing installation
  - GPIO Menu
- 21.8 NTP Server
- 21.9 Grouped Networks
- 21.10 SIM Toolkit
22 AP - access point
- 23 AP Controller
- 23.1 Wireless SSID
- 23.2 Settings
24 AP Controller Status
- 24.1 Info
- 24.2 Access Point (Usage)
- 24.3 Wireless SSID
- 24.4 Wireless Client
- 24.5 Nearby Device

https://www.peplink.com

106

Matching traffic will be routed through the specified WAN connection, regardless of the health

check status of the WAN connection. Starting from Firmware 5.2, outbound traffic can be

enforced to go through a specified SpeedFusion

connection.

13.2.4 Algorithm: Priority

This setting specifies the priority of the WAN connections used to route the specified network

service. The highest priority WAN connection available will always be used for routing the

specified type of traffic. A lower priority WAN connection will be used only when all higher priority

connections have become unavailable.

Starting from Firmware 5.2, outbound traffic can be prioritized to go through SpeedFusion

connection(s). By default, VPN connections are not included in the priority list.

Tip

Configure multiple distribution rules to accommodate different kinds of services.

13.2.5 Algorithm: Overflow

The traffic matching this rule will be routed through the healthy WAN connection that has the

highest priority and is not in full load. When this connection gets saturated, new sessions will

be routed to the next healthy WAN connection that is not in full load.