User's Manual

ManualsBrandsPEPWAVE ManualsElectronicsPEPWAVE / peplink Wireless Product

191

192

193

194

195

196

197

198

199

200

Table Of Contents

1 Introduction and Scope
Glossary
2 Product Features
- 2.1 Supported Network Features
- 2.2 Other Supported Features
3 Pepwave MAX Mobile Router Overview
- 3.1 MAX BR1 Mini Core
4 Advanced Feature Summary
- 4.1 Drop-in Mode and LAN Bypass: Transparent Deployment
- 4.2 QoS: Clearer VoIP
- 4.3 Per-User Bandwidth Control
- 4.4 High Availability via VRRP
- 4.5 USB Modem and Android Tethering
- 4.6 Built-In Remote User VPN Support
- 4.7 SIM-card USSD support
5 Installation
- 5.1 Preparation
- 5.2 Constructing the Network
- 5.3 Configuring the Network Environment
6 Mounting the Unit
- 6.1 Wall Mount
7 Connecting to the Web Admin Interface
8 Configuring the LAN Interface(s)
- 8.1 Basic Settings
- 8.2 Port Settings
- 8.3 Captive Portal
9 Configuring the WAN Interface(s)
- 9.1 Ethernet WAN
- 9.2 Cellular WAN
- 9.3 Wi-Fi WAN
  - 9.3.1 Creating Wi-Fi Connection Profiles
- 9.4 WAN Health Check
- 9.5 Dynamic DNS Settings
10 Advanced Wi-Fi Settings
11 ContentHub Configuration
- 11.1 ContentHub
- 11.2 Configuring the ContentHub
- 11.3 Configure a website to be published from the ContentHub
- 11.4 Configure an application to be published from the ContentHub
12 MediaFast Configuration
- 12.1 Setting Up MediaFast Content Caching
- 12.2 Scheduling Content Prefetching
- 12.3 Viewing MediaFast Statistics
13 Bandwidth Bonding SpeedFusionTM / PepVPN
- 13.1 PepVPN
- 13.2 The Pepwave Router Behind a NAT Router
- 13.3 SpeedFusionTM Status
14 IPsec VPN
- 14.1 IPsec VPN Settings
15 Outbound Policy Management
- 15.1 Outbound Policy
- 15.2 Custom Rules for Outbound Policy
16 Inbound Access
- 16.1 Port Forwarding Service
  - 16.1.1 UPnP / NAT-PMP Settings
17 NAT Mappings
18 QoS
- 18.1 User Groups
- 18.2 Bandwidth Control
- 18.3 Application
19 Firewall
- 19.1 Outbound and Inbound Firewall Rules
- 19.2 Content Blocking
- 20 OSPF & RIPv2
- 21 BGP
22 Remote User Access
- 22.1 L2TP with IPsec
- 22.2 OpenVPN
- 22.3 PPTP
- 22.4 Authentication Methods
23 Miscellaneous Settings
- 23.1 High Availability
- 23.2 Certificate Manager
- 23.3 Service Forwarding
- 23.4 Service Passthrough
- 23.5 UART
- 23.6 GPS Forwarding
- 23.7 Ignition Sensing
  - Ignition Sensing installation
  - GPIO Menu
- 23.8 Grouped Networks
- 23.9 SIM Toolkit
24 AP - access point
- 25 AP Controller
- 25.1 Wireless SSID
- 25.2 Settings
26 AP Controller Status
- 26.1 Info
- 26.2 Access Point (Usage)
- 26.3 Wireless SSID
- 26.4 Wireless Client
- 26.5 Nearby Device
- 26.6 Event Log
27 Toolbox
28 System Settings
- 28.1 Admin Security
- 28.2 Firmware
- 28.3 Time
- 28.4 Schedule
- 28.5 Email Notification
- 28.6 Event Log
- 28.7 SNMP
- 28.8 InControl
- 28.9 Configuration
- 28.10 Feature Add-ons
- 28.11 Reboot
29 Tools
- 29.1 Ping
- 29.2 Traceroute Test
- 29.3 PepVPN Test
- 29.4 Wake-on-LAN
- 29.5 CLI (Command Line Interface Support)
30 Status
- 30.1 Device
  - 30.2 GPS Data
- 30.3 Active Sessions
- 30.4 Client List
- 30.5 WINS Client
- 30.6 UPnP / NAT-PMP
- 30.7 OSPF & RIPv2
- 30.8 BGP
- 30.9 SpeedFusion Status
- 30.10 Event Log
- 31 WAN Quality
- 32 Usage Reports
- 32.1 Real-Time
- 32.2 Hourly
- 32.3 Daily
- 32.4 Monthly
Appendix A: Restoration of Factory Defaults
Appendix B: Declaration

https://www.peplink.com

Industry Canada Statement ( for MAX BR1 Classic )

This device complies with Industry Canada’s licence-exempt RSSs. Operation is subject to the following

two conditions:(1) This device may not cause interference; and(2) This device must accept any

interference, including interference that may cause undesired operation of the device.

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts

de licence. L'exploitation est autorisée aux deux conditions suivantes :(1) l'appareil ne doit pas produire

de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si

le brouillage est susceptible d'en compromettre le fonctionnement.

This equipment complies with Innovation, Science and Economic Development Canada RF exposure

limits set forth for an uncontrolled environment. This equipment should be installed and operated to

ensure a minimum of 20 cm spacing to any person at all times.

Déclaration d'exposition aux radiations: Cet équipement est conforme aux limites d'exposition aux

rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et

utilisé avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps.

This radio transmitter has been approved by Innovation, Science and Economic Development Canada

to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna

types not included in this list that have a gain greater than the maximum gain indicated for any type

listed are strictly prohibited for use with this device.

Antenna types: Replacement Antenna Antenna

gain (in dBi): 5.33 dBi

Innovation, Sciences et Développement économique Canada a approuvé l'utilisation de ce transmetteur

radio avec les types d'antenne énumérés ci-dessous, le gain maximal admissible étant indiqué. Les

types d'antennes non inclus dans cette liste qui ont un gain supérieur au gain maximal indiqué pour tout

type listé sont strictement interdits pour une utilisation avec cet appareil.

Types d'antennes: Replacement Antenna

Gain d'antenne (en dBi): 5.33 dBi