Datasheet

Germany: [phone]Pepperl+Fuchs Group
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
USA: [phone] Singapore: [phone]
www.pepperl-fuchs.com [e-mail] [e-mail]
[e-mail]
1
Ultrasonic sensor UC800-F77S-EP-IO-V31
Release date: 2018-04-18 13:58 Date of issue: 2018-04-18 261244_eng.xml
Technical data
General specifications
Sensing range 60 ... 800 mm
Adjustment range 70 ... 800 mm
Dead band 0 ... 60 mm
Standard target plate 100 mm x 100 mm
Transducer frequency approx. 255 kHz
Response delay minimum : 13 ms
factory setting: 49 ms
Sensor cycle time ≥ 13 ms (factory setting) ;
programmable to 60 s
Memory
Non-volatile memory EEPROM
Write cycles 300000
Indicators/operating means
LED green solid: Power on
flashing: Standby mode or IO-Link communication
LED yellow solid: object in evaluation range
flashing: switch point programming, object detected
LED red solid: error
flashing: switch point programming, object not detected
Electrical specifications
Operating voltage U
B
10 ... 30 V DC , ripple 10 %
SS
No-load supply current I
0
≤ 40 mA
Power consumption P
0
≤ 400 mW
Time delay before availability t
v
≤ 300 ms
Interface
Interface type IO-Link (via C/Q = Pin 4)
Device profile Smart Sensor
Transfer rate COM 2 (38.4 kBaud)
IO-Link Revision 1.1
Min. cycle time 2.3 ms
Process data witdh 16 bit
SIO mode support yes
Device ID 0x300302 (3146498)
Compatible master port type A
Input/Output
Input/output type 1 synchronization connection, bidirectional
0 Level 0 ... 1 V
1 Level 2.5 V ... U
B
Input impedance > 22 kΩ
Output rated operating current current source < 2.5 mA
Pulse length ≥ 1 ms with external control, low active
Synchronization frequency
Common mode operation ≤ 82 Hz
Multiplex operation ≤ 82 Hz / n , n = number of sensors , n ≤ 10
Output
Output type 1 push-pull (4 in 1) output, short-circuit protected, reverse
polarity protected
Rated operating current I
e
100 mA , short-circuit/overload protected
Voltage drop U
d
≤ 2.5 V
Repeat accuracy ≤ ± 0.1 % of full-scale value
Switching frequency f factory setting: 12 Hz programmable max. 27 Hz
Range hysteresis H 1 % of the adjusted operating range (default settings),
programmable , min. 1 mm
Temperature influence ≤ ± 0.75 % of the end value (with temperature compensation)
from 10 minutes after switching on the sensor ; 0,17 %/K
(without temperature compensation)
Ambient conditions
Ambient temperature -25 ... 70 °C (-13 ... 158 °F)
When fixing with one M18 nut, the temperature range begins
with 0°C (32°F).
Storage temperature -40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type Connector plug M8 x 1 , 4-pin
Degree of protection IP67
Material
Housing Polycarbonate
Transducer epoxy resin/hollow glass sphere mixture; polyurethane foam
Installation position any position
Mass 13 g
Tightening torque, fastening screws with M3 nuts max. 0.2 Nm
with M18 nuts max. 1 Nm
Factory settings
Output near switch point: 70 mm
far switch point: 800 mm
Output mode: Window mode
Output logic: normally open
Beam width wide
Compliance with standards and
directives
Standard conformity
Model Number
UC800-F77S-EP-IO-V31
Single head system
Features
• IO-link interface for service and
process data
• Programmable via DTM with
PACTWARE
• Continuous distance value via IO-
Link process data
• Selectable sound lobe width
• Synchronization options
• Temperature compensation
• Push-pull output
Diagrams
Characteristic response curve
Distance X [mm]
Distance Y [mm]
flat surface 100 mm x 100 mm
round bar, Ø 25 mm
wide sound beam
medium-sized sound beam
narrow sound beam
0 200 400 600 800 1000 1200
200
150
100
50
0
-50
-100
-150
-200
X
Y