Datasheet

Germany: [phone]Pepperl+Fuchs Group
Refer to “General Notes Relating to Pepperl+Fuchs Product Information”.
USA: [phone] Singapore: [phone]
www.pepperl-fuchs.com [e-mail] [e-mail]
[e-mail]
1
Ultrasonic sensor UC400-F77-IU-IO-V31
Release date: 2017-10-24 11:48 Date of issue: 2017-10-27 261247_eng.xml
Technical data
General specifications
Sensing range 30 ... 400 mm
Adjustment range 40 ... 400 mm
Dead band 0 ... 30 mm
Standard target plate 20 mm x 20 mm
Transducer frequency approx. 310 kHz
Response delay minimum : 10 ms
factory setting: 37 ms
Sensor cycle time ≥ 10 ms (factory setting) ;
programmable to 60 s
Memory
Non-volatile memory EEPROM
Write cycles 300000
Indicators/operating means
LED green solid: Power on
flashing: Standby mode or IO-Link communication
LED yellow solid: object in evaluation range
flashing: programming of the limits, object detected
LED red solid: fault
Flashing: programming limits, object not detected
Electrical specifications
Operating voltage U
B
18 ... 30 V DC , ripple 10 %
SS
No-load supply current I
0
≤ 50 mA
Power consumption P
0
≤ 500 mW
Time delay before availability t
v
≤ 300 ms
Interface
Interface type IO-Link (after individual activation via programming button)
Input/Output
Input/output type 1 synchronization connection, bidirectional
0 Level 0 ... 1 V
1 Level 2.5 V ... U
B
Input impedance > 22 kΩ
Output rated operating current current source < 2.5 mA
Pulse length ≥ 1 ms with external control, low active
Synchronization frequency
Common mode operation ≤ 109 Hz
Multiplex operation ≤ 109 Hz / n , n = number of sensors , n ≤ 10
Output
Output type 1 analog output 0 (4) ... 20 mA or
1 analog output 0 ... 10 V
Resolution current output: evaluation range [mm]/3200 but ≥ 0.35 mm
voltage output: evaluation range [mm]/4000 but ≥ 0.35 mm
Deviation of the characteristic curve ≤ ± 1 % of full-scale value
Repeat accuracy ≤ ± 0.1 % of full-scale value
Load impedance current output: ≤ 500 Ohm
voltage output: ≥ 1000 Ohm
Temperature influence ≤ ± 0.75 % of the end value (with temperature compensation)
from 10 minutes after switching on the sensor ; 0,17 %/K
(without temperature compensation)
Ambient conditions
Ambient temperature current output -25 ... 60 °C (-13 ... 140 °F) voltage output -25
... 70 °C (-13 ... 158 °F)
Storage temperature -40 ... 85 °C (-40 ... 185 °F)
Mechanical specifications
Connection type Connector plug M8 x 1 , 4-pin
Degree of protection IP67
Material
Housing Polycarbonate
Transducer epoxy resin/hollow glass sphere mixture; polyurethane foam
Installation position any position
Mass 9 g
Tightening torque, fastening screws max. 0.2 Nm
Factory settings
Output near limit: 40 mm
far limit: 400 mm
Output mode: rising ramp
output type: 4 ... 20 mA
Beam width wide
Compliance with standards and
directives
Standard conformity
Standards EN 60947-5-2:2007+A1:2012
IEC 60947-5-2:2007 + A1:2012
EN 60947-5-7:2003
IEC 60947-5-7:2003
Approvals and certificates
UL approval cULus Listed, Class 2 Power Source
CCC approval CCC approval / marking not required for products rated ≤36 V
Model Number
UC400-F77-IU-IO-V31
Single head system
Features
• IO-Link interface for
parameterization
• Programmable via DTM with
PACTWARE
• Selectable sound lobe width
• Synchronization options
• Temperature compensation
•Analog output
Diagrams
Characteristic response curve
Distance X [mm]
Distance Y [mm]
flat surface 100 mm x 100 mm
round bar, Ø 25 mm
wide sound beam
medium-sized sound beam
narrow sound beam
0 100 200 300 400 500 600 700
150
100
50
0
-50
-100
-150
X
Y