e01_kb341_cover_41e.qk 3/4/2003 2:44 PM Page 1 Digital Camera Operating Manual To ensure the best performance from your camera, please read the Operating Manual before using the camera.
e01_kb341_cover_41e.qk 03.2.14 4:11 PM Page 2 Thank you for buying the Pentax Optio S Digital Camera. Please read this manual before using the camera in order to get the most out of all the features and functions. Keep this manual safe, as it can be a valuable tool in helping you to understand all the camera's capabilities.
e02_kb341_001_027_41e.qk 03.2.14 4:04 PM Page 1 FOR SAFE USE OF YOUR CAMERA Sufficient attention has been paid to the safety of this product but please pay particular attention to the warnings indicated by the following symbols during use. Warning These symbols indicate that it is possible that the user may experience serious difficulties if the warnings are not heeded.
e02_kb341_001_027_41e.qk 03.2.14 4:04 PM Page 2 Care to be Taken During Handling 2 • Do not clean the product with organic solvents such as thinner or alcohol benzene. • Places of high temperature and humidity should be avoided. Particular care should be taken regarding vehicles, which can become very hot inside. • Storing the camera where pesticides and chemicals are handled should be avoided.
e02_kb341_001_027_41e.qk 03.2.
e02_kb341_001_027_41e.qk 03.2.
e02_kb341_001_027_41e.qk 03.2.
e02_kb341_001_027_41e.qk 03.2.14 4:04 PM Page 10 Getting Started Names of Operating Parts Attaching the Strap Zoom / / Getting Started Focus status lamp (green) Flash status lamp (red) / button / / / button Shutter release button Power switch button Four-way controller (OK button in the center) Speaker Playback button Display button Menu button Pass the narrow end of the strap through the strap lug and pass the other end through the loop.
e02_kb341_001_027_41e.qk 03.2.14 4:04 PM Page 12 Powering the Camera Charging indicator Battery c c x Battery lock lever x Battery charger z Battery/Card cover z Battery AC plug cord Getting Started Getting Started To power outlet Installing the Battery Charging the Battery Install the battery provided. When using the camera for the first time, charge the battery before installing. When using the camera for the first time or when the [Battery depleted.
e02_kb341_001_027_41e.qk 03.2.14 4:04 PM Page 14 ● Approximate Operating Time (when the D-LI8 battery is fully charged) Number of recordable images : Approx. 160 (when 50% shooting uses flash, LCD monitor ON) Playback time : Approx. 110 min. To power outlet AC plug cord c AC adapter ● Battery Level Indicator You can check the battery level by the the LCD monitor.
e02_kb341_001_027_41e.qk 03.2.14 4:04 PM Page 16 Installing the SD Memory Card/MultiMediaCard Battery/Card cover SD Memory Card/ MultiMediaCard Precautions When Using a SD Memory Card/MultiMediaCard • Make sure that the camera is turned off before opening the battery/Card cover. Write-protect • The SD Memory Card/MultiMediaCard is equipped with a switch write-protect switch.
e02_kb341_001_027_41e.qk 03.2.14 4:04 PM Page 18 Initial Settings Setting the Home Town You can choose the city (Home Town) in which you will use the camera. Power switch Initial Setting Language/ Playback button memo If the initial settings screen appears when you turn the camera on, follow the procedure below to set the display language, Home Town, DST, video output format and current date and time.
e02_kb341_001_027_41e.qk 03.2.14 4:04 PM Page 20 n Setting the Date and Time Set the current date and time. z Date Adjust 1 / 1 / 2003 0 : 00 MENU x Press the four-way controller ( ). and will be displayed above and below the day. Exit DISP 12/24 OK Ok Date Adjust 1 / 1 / 2003 memo • When the initial settings screen is displayed, you can cancel the settings operation and switch to Capture mode by pressing the MENU button.
e02_kb341_001_027_41e.qk 03.2.14 4:04 PM Page 22 Quick Start c Taking Still Pictures Shutter release button Power switch Viewfinder Using the Shutter Release Button Display button Zoom / / button For the simplest procedure to take still pictures: The flash fires automatically depending on the light conditions. z x Press the power switch. The camera will turn on. Confirm the subject and shooting information on the LCD monitor.
e02_kb341_001_027_41e.qk 03.2.14 4:04 PM Page 24 Quick Start Playing Back Still Pictures Deleting the displayed image. LCD monitor Four-way controller (OK button) Playback button Playing Back Images You can display the still picture. z Press the Playback button after taking a picture. The image taken will be dis-played on the LCD monitor. Playing Back Previous or Next Images Still images can be played back one at a time, proceeding either forward or backward. z x memo File No.
e02_kb341_001_027_41e.qk 03.2.14 4:04 PM Page 26 Quick Start How to View the Recorded Images Viewing images on the camera One of the advantages of a digital camera is that it enables you to view your pictures immediately after you have taken them. You can check the composition and brightness and take the picture again if you are not satisfied. Playing Back Still Pictures ☞ p.79 Viewing images on a TV If you want to show your pictures to friends, you can display them on your TV monitor.
e03_kb341_028_078_41e.qk 03.2.14 4:05 PM Page 28 Common Operations Turning the Camera On and Off Using the Button Functions z Power switch Playback button z Playback Only Mode Press the power switch on while pressing the Playback button activates the Playback Only mode. • When the camera turns on in Playback Only mode, the lens does not extend. • To switch from Playback Only mode to Capture mode, turn the camera off and then turn it on again. Playing Back Still Pictures ☞ p.
e03_kb341_028_078_41e.qk 03.2.14 4:05 PM Page 30 Playback Mode button Deletes the image. (☞ p.84) button Protects the image from erasure. (☞ p.87) Zoom / / button displays nine images at once. (☞ p.82) – + changes the size of the Zoom Display image, displayed on the LCD monitor. (☞ p.79) Four-way controller ( ) ( ) Sets the DPOF (☞ p.89) for the print service. ( ) Displays the image you wish to view. (☞ p.
e03_kb341_028_078_41e.qk 03.2.14 4:05 PM Page 32 Setting the Menus Example of menu operation z MENU button When you press the MENU button, the menus are displayed on the LCD monitor. You can set functions, save the settings, and change the camera settings on these menus. x [ [ Rec.Mode] menu Playback] menu How to Set the Menus When you are making settings from a menu, a guide to operation is displayed on the LCD monitor.
e03_kb341_028_078_41e.qk 03.2.14 4:05 PM Page 34 [ Menu List Playback] Menu Item [ Rec.Mode] Menu : Adjustable : Any changes made are invalid. Item Description Recorded Pixels For selecting the size of recorded pixels. Quality Level For selecting the image compression rate. White Balance For adjusting the color balance according to lighting. Default Setting 2048 × 1536 Reference 320 × 240 p.41 p.42 Sensitivity For setting the Sensitivity.
e03_kb341_028_078_41e.qk 03.2.14 4:05 PM Page 36 Taking Pictures z Setting the Shooting Functions Changing the Mode Capture mode is for taking pictures and Playback mode is for playing back or erasing images. Switching between Capture Mode and Playback Mode • To change from Capture mode to Playback mode, press the Playback button. • To change from Playback mode to Capture mode, press the Playback button or the shutter release button halfway.
e03_kb341_028_078_41e.qk Caution 03.2.14 4:05 PM Page 38 z If you take a picture while looking through the viewfinder when the focus mode is set on Macro and Super Macro, the range of the resulting picture will differ from what was seen in the viewfinder. Be sure to check the image on the LCD monitor. Manual Focus When the mode is set to , the central portion of the picture is enlarged to full screen on the LCD monitor for focus adjustment.
e03_kb341_028_078_41e.qk 03.2.14 4:05 PM Page 40 Displaying Shooting Information in Capture Mode Rec. Mode You can display information on the LCD monitor when shooting. The display mode can be changed by pressing the Display button. xc 123 4 5 9 6 Display On Shooting information is displayed.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 42 Rec. Mode xc z Recorded Pixels Quality Level White Balance Focusing Area AE Metering Sensitivity 1/3 MENU Exit Rec. Mode 2048 1556 AWB Multiple OK 1/3 MENU 2048 1556 AWB Multiple Auto Exit OK Ok Adjusting the Color Balance according to Lighting (White Balance) You can take pictures in natural colors by adjusting the white balance according to the light conditions at the time of shooting.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 44 Manual Setting z x c v Rec. Mode Select [ ] (manual) on the white balance screen. White Balance AWB Point your camera at a blank sheet of paper so that it fills the screen. xc DISPLAY z Adjust Press the Display button. The white balance is automatically adjusted, [Adjust] is displayed on the LCD monitor and the display returns to the menu screen. MENU Press the OK button. The camera is ready to take the picture.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 46 Rec. Mode Recorded Pixels Quality Level White Balance Focusing Area AE Metering Sensitivity xc z 1/3 MENU Exit Rec. Mode 2048 1556 AWB Multiple xc Auto OK z Ok Setting the Light Metering Range to Determine the Exposure (AE Metering) You can choose which part of the screen to use to measure the brightness and determine the exposure. The exposure is determined by the entire screen. The exposure is determined mainly by the center of the screen.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 48 Rec. Mode xc z Recorded Pixels Quality Level White Balance Focusing Area AE Metering Sensitivity 1/3 MENU Rec.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 50 Rec. Mode Recorded Pixels Quality Level White Balance Focusing Area AE Metering Sensitivity xc z 1/3 MENU Rec. Mode 2048 1556 Exit AWB Multiple OK MENU Exit AWB Multiple Auto OK Ok Setting the Image Contrast (Contrast) You can set the image contrast. z x Rec.Mode] menu. Use the four-way controller ( ) to change the setting from [Normal] to [Hard (+)] or [Soft (–)]. Press the OK button. The camera is ready to take the picture.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 52 Taking Pictures Rec. Mode xc z Recorded Pixels Quality Level White Balance Focusing Area AE Metering Sensitivity 1/3 MENU Exit 2048 1556 AWB Multiple b Auto OK Ok zxc v EV Compensation Setting the Functions (Standard Mode) You can take pictures that are intentionally over-exposed or under-exposed. z c In Standard mode ( z ± 0.0 x OK Ok Saving the EV Compensation Value ☞ p.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 54 n v zxcvb zxc Selecting the Picture Mode According to the Shooting Scene (Picture mode) You can select the Picture mode according to the shooting scene. Picture mode There are nine available modes in Picture mode. Landscape Flower Enables to take flower photos bright in color. Portrait Enables to take portraits with spatial effect, by emphasizing the person.
e03_kb341_028_078_41e.qk 3/5/03 10:17 AM Page 56 Keeping the shutter release button pressed vb If you keep the shutter release button pressed for more than one second, pictures will be taken for as long as you keep the button pressed. Shooting stops when you take a finger off from the shutter release button. zxc Playing Back Movie Pictures ☞ p.80 Caution Taking Movie Pictures (Movie Picture Mode) This mode enables you to take moving images and sound.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 58 n b zxcvm m memo Caution Taking Panorama Pictures (Panorama Assist Mode) You can take a number of images and join them together to form a panorama picture. The panorama software provided with the camera and a computer that supports Windows are necessary for joining the images. x c v b 58 Press the four-way controller ( ) in Capture mode. The virtual mode dial appears.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 60 n Setting the slim filter When you select the slim filter in Digital Filter Mode, the slimness setting screen is displayed. zxcvb z Use the four-way controller ( ) to set the slimness. Decreases slimness. Increases slimness. x Taking Pictures with Digital Filters (Digital Filter Mode) Caution Press the OK button. The camera returns to digital filter mode. • The digital zoom cannot be used when the slim filter is selected.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 62 ,⁄0 v xcvbnm zxc z Taking Stereo Pictures (3D Image Mode) Using Preset Function Settings (User Mode) In User mode, you can take pictures using the functions and settings registered in advance in User mode. z c v Use the four-way controller ( ) to select User mode ( ). Press the OK button. Press the shutter release button. The picture is taken. Registering Functions in User Mode ☞ p.75 5 Select the viewing mode.
e03_kb341_028_078_41e.qk m , . ⁄0 4:06 PM Page 64 Press the OK button. The screen for taking the first image appears in the left half of the LCD monitor. 14 Take the first image. Hold the camera so that the subject is in the middle of the left half of the screen and press the shutter release button. The image is displayed in the left half of the LCD monitor. The right half of the screen is for taking the second image. 10/20/2003 11:19 14 Move the camera to the right without changing your stance.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 66 How to view 3D pictures using the 3D image viewer Example of a 3D picture Print out the pictures so that they are about 11cm or 12cm wide and place the divider of the 3D image viewer in the middle of the two. three-dimensional effect even when looking at prints that are the same size. It may be especially difficult if the pictures are very large or very small. Try different sizes until the right effect is achieved.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 68 x x z z Continuous Shooting (Continuous Shooting Mode) Using the Self-Timer Pictures are taken continuously while the shutter release button is pressed. The picture will be taken 10 seconds after the shutter release button is pressed. z z 198 x 10/20/2003 11:19 x Press the shutter release button. Pictures will be taken continuously while the shutter release button is pressed.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 70 z z Using the Remote Control Unit (optional) Using the Zoom You can use the zoom to take pictures in Tele or Wide mode. You can take pictures using the remote control F (optional). z z 198 Press the Zoom button in Capture mode. 198 : makes the subject larger : makes the subject smaller 10/20/2003 11:19 Press the shutter release button on the remote control unit.
e03_kb341_028_078_41e.qk 3/4/2003 2:51 PM Page 72 Enabling the Digital Zoom Function z Caution Press the MENU button in Capture mode. The [ Rec.Mode] menu will be displayed. x Press the four-way controller ( ) to select [Digital Zoom]. c Use the four-way controller ( ) to select [On]. v b Press the OK button. The camera is ready to take a picture. xcv Rec.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 74 z Saving the Settings (Memory) x Saving the Menu Items (Memory) You can choose whether you want the set values to be saved when the camera is turned off. If you select [On], the settings will be saved in the status they were in immediately before the camera was turned off. If you select [Off], the settings will be reset to the defaults when the camera is turned off.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 76 Recording and Playback Recording Sound (Voice Recorder Mode) You can record sound. The recordable time is displayed on the LCD monitor according to how much space is available on the SD Memory Card/MultiMediaCard. Playing Back Sound You can play back the recording you made in Voice Recorder Mode. xc zv xcv zb z Press the power switch for more than 2 seconds. x c Press the shutter release button. Recording stops.
e03_kb341_028_078_41e.qk 03.2.14 4:06 PM Page 78 Adding a Voice Memo You can add a voice memo to a captured image. zxc z Recording and Playback 78 x c memo Caution Enter the playback mode and choose the image to which you want to add a voice memo with the four-way controller ( ). The voice memo screen will be displayed on the LCD monitor while the image is displayed. 100-0020 100-0019 10/20/2003 11:19 Press the OK button. Recording starts. You can record for up to 30 seconds.
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 79 Playback/Erasing/Editing Playing Back Images x z c Playing Back Still Pictures See “Playing Back Images” (p.24), or “Playing Back Previous or Next Images” (p.25). Zoom Display You can display images magnified up to a maximum of 4 times. A guide to operation is displayed on the LCD monitor during magnification. (The magnification varies depending on the number of recorded pixels.
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 80 Displaying shooting information in Playback mode Shooting information can be displayed on the LCD monitor. Pressing the Display button switches the information displayed. zxc Displays shooting information.
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 82 xc z zcvb x Nine-image Display Slideshow You can display nine images at the same time. z x Enter the Playback mode and choose an image with the four-way controller ( ). z Press / on the Zoom button / . Nine images will be displayed with the selected image in the center. Choose an image with the four-way controller ( ).
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 84 Erasing a Voice Memo only Erasing Images If an image has a voice memo, you can erase the voice memo without erasing the image. x z zcv x c v x c 100-0020 Select [Sound Delete] with the four-way controller ( ). Press the OK button. Sound Delete Delete Cancel MENU Exit All Images es OK Ok memo the voice memo. Enter the Playback mode and choose the image or voice memo you want to erase with the four-way controller ( ). Press the button.
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 86 z x xc zcv Erasing All Images Protecting Images/sound from Deletion (Protect) You can protect images/sound from being accidentally erased. You can erase all the images and sound at once. z • Once erased, images cannot be restored. • Protected images/sound cannot be erased. Caution z x Select [Delete All] with the fourway controller ( ). Press the OK button.
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 88 Viewing Images on a TV Setting the Printing Service (DPOF) You can print the images on the SD Memory Card/MultiMediaCard using a DPOF (Digital Print Order Format) compatible printer or at a printing service. zxcvb By using the AV cable, you can capture and play back images on a TV or other equipment with a video IN jack. Make sure that both the TV and the camera are turned off before connecting the cable.
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM c Use the four-way controller ( ) to select the number of prints, then press the four-way controller ( ). The frame will move to [Date]. v Use the four-way controller ( ) to select whether to insert the date or not. Page 90 100-0020 Copies Date MENU Exit DISP 3 zcvbn All Images Ima OK Ok x (On): The date will be imprinted (Off): The date will not be imprinted b Press the OK button. Prints can be made according to the settings.
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 92 n Editing Images Press the OK button. 100-0020 Select resolution and quality Recorded Pixels Quality Level MENU m Four-way controller (OK button in the center) , . Menu button Changing the Image Size By changing the size and quality of a selected image, you can make the file smaller than the original. After changing the size, the image can be saved as a new image or written over the original image.
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 94 Copying Files Trimming Images You can trim part of a picture and save it as a separate image. z x c v b n Press the four-way controller ( ). The [ Playback] menu will be displayed. Press the four-way controller ( ) to select [Trimming]. Press the four-way controller ( ). The image that can be trimmed. Choose the image you want to trim with the four-way controller ( ). Press the OK button. The trimming screen will be displayed.
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 96 Viewing Images with your PC By using the provided USB cable (I-USB7) or card reader and image-browser software, you can transfer images recorded with the camera to your PC and edit them or print them out. This section explains how to view images on your PC using the provided software (S-SW8). Installing the software The procedures for installing the necessary software are explained.
e04_kb341_079_109_41e.qk 2003/02/20 5:51 PM Page 98 b n Click [Next] and then click [Finish]. Reboot your computer after the screen closes. Turn your camera off and plug the USB cable into your camera and into an available USB port on your computer. Installing the ACDSee™ When installing the ACDSee™, recorded images can be viewed and edited on your computer. z x Turn on your computer. Insert the CD-ROM (S-SW8) into your CD-ROM drive. The PENTAX Software Installer screen will appear.
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 100 Displaying and copying images using ACDSee™ z x Turn your computer on. Make sure the camera is turned off and connect it to your computer with the USB cable. Make sure that there is an SD Memory Card/ MultiMediaCard in the camera. memo • If you are using Windows XP and there is a volume label on the SD Memory Card/MultiMediaCard, the name on the volume label will be displayed instead of [Removable Disk].
e04_kb341_079_109_41e.qk c 03.2.14 4:07 PM Page 102 Adjust the position of the images. [ACD photostitcher] starts up and the selected images are displayed in panorama format. If you move the mouse pointer onto an image, the pointer changes to a symbol. Adjust the position of the images by pressing the left mouse button and moving the images one by one to the desired position. When you have finished correcting the position, click the [STITCH] button. b Trim the picture.
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 104 Disconnecting your camera from your PC Disconnecting your camera from your PC (Windows XP) z Disconnecting the camera from your PC (Windows 2000/Me) z x x Double click the [Unplug or eject hardware] icon in the task bar recognized area. The [Unplug or eject hardware] screen will appear. Make sure [PENTAX USB DISK Device] is selected and click [Stop]. [Stop Hardware Device] screen will appear. c Click [OK].
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 106 Viewing Images with your Macintosh Installing the software z x By using the provided USB cable (I-USB7) or card reader and image-browser software, you can transfer images recorded with the camera to your Macintosh and edit them or print them out. This section explains how to view images on your Macintosh using the provided software (S-SW8).
e04_kb341_079_109_41e.qk 03.2.14 4:07 PM Page 108 Displaying and copying images using ACDSee™ z x Turn your Macintosh on. Make sure the camera is turned off and connect it to your Macintosh with the USB cable. Make sure that there is an SD Memory Card/ MultiMediaCard in the camera. memo • If there is a volume label on the SD Memory Card/ MultiMediaCard, the name on the volume label will be displayed instead of [untitled].
e05_kb341_110_136_41e.qk 03.2.14 4:09 PM Page 110 Settings Camera Settings How to recall the [ Set-up Format Sound Start-up Screen Date Style Date Adjust World Time Set-up] menu Rec.
e05_kb341_110_136_41e.qk How to recall [ 03.2.14 4:09 PM Page 112 Set-up] menu Rec.
e05_kb341_110_136_41e.qk How to recall the [ 03.2.14 4:09 PM Page 114 Set-up] menu Rec. Mode Four-way controller (OK button in the center) Menu button Recorded Pixels Quality Level White Balance Focusing Area AE Metering Sensitivity 1/3 MENU Set-up 2048 1556 Format Sound Start-up Screen Date Style Date Adjust World Time AWB Multiple Exit Auto OK Ok 1/3 c Changing the Date/Time You can change the initial date and time settings. z x Select [Date Adjust] on the [ Set-up] menu.
e05_kb341_110_136_41e.qk How to recall the [ 03.2.14 4:09 PM Page 116 Set-up] menu Rec. Mode Four-way controller (OK button in the center) Menu button Recorded Pixels Quality Level White Balance Focusing Area AE Metering Sensitivity 1/3 MENU Exit Set-up 2048 1556 AWB Multiple Auto OK Ok Changing the Display Language 1/3 MENU Exit On On mm/dd/yy 1/ 1/2003 Off OK Ok Changing the Video Output Format You can change the language in which the menus, error messages, etc. are displayed.
e05_kb341_110_136_41e.qk How to recall the [ 03.2.14 4:09 PM Page 118 Set-up] menu Rec.
e05_kb341_110_136_41e.qk How to recall the [ 03.2.14 4:09 PM Page 120 Set-up] menu Rec. Mode Recorded Pixels Quality Level White Balance Focusing Area AE Metering Sensitivity Four-way controller (OK button in the center) Menu button 1/3 MENU Exit Auto OK Ok Registering a function c memo 1/3 MENU Exit On On mm/dd/yy 1/ 1/2003 Off OK Ok Resetting to Default Settings (Reset) You can register the functions you use most frequently on the four-way controller ( ).
e05_kb341_110_136_41e.qk 03.2.14 4:09 PM Page 122 v Setting the Alarm b You can set the alarm to ring at a specified time and display a selected image. Four-way controller (OK button in the center) Menu button m , Checking the Alarm c v Press the four-way controller ( ). The [ Playback] menu will be displayed. Press the four-way controller ( ). The list of alarms will be displayed. Active alarms are indicated by .
e05_kb341_110_136_41e.qk 03.2.14 4:09 PM Page 124 Appendix Optional Accessories List of City Names Refer to following list of city and code names for setting the world time.
e05_kb341_110_136_41e.qk 03.2.14 4:09 PM Page 126 Messages Messages such as the following may be displayed on the LCD monitor during camera operation. Memory Card full Built-in Memory Full No image & sound Camera can not display this image & sound. There are no images or sound on the SD Memory Card/MultiMediaCard or in the Built-in memory. You are trying to play back an image in a format not supported by this camera. You may be able to display it on another brand of camera or PC. Battery depleted.
e05_kb341_110_136_41e.qk 03.2.14 4:09 PM Page 128 Troubleshooting Problem Subject is not in focus Problem Power will not come on No image on the LCD monitor Shutter will not release Picture is dark Subject is not in focusing area Position subject in AF frame (focusing area) in middle of LCD monitor. If the subject is outside the focusing area, aim the camera at the subject and lock the focus (press shutter release button halfway), then compose picture and press the shutter release button fully.
e05_kb341_110_136_41e.qk 3/4/2003 2:54 PM Page 130 LCD Monitor Playback Functions Main Specifications Type Fully automatic compact-type digital still camera with built-in zoom lens Effective Pixels 3.2 megapixels Sensor 3.34 megapixels (total pixels) 1/2.
e05_kb341_110_136_41e.qk 03.2.14 4:09 PM Page 132 WARRANTY POLICY All Pentax cameras purchased through authorized bona fide photographic distribution channels are guaranteed against defects of material or workmanship for a period of twelve months from date of purchase.
e05_kb341_110_136_41e.qk 03.2.14 4:09 PM Page 134 For customers in USA STATEMENT OF FCC COMPLIANCE This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
e05_kb341_110_136_41e.qk MEMO 03.2.
e05_kb341_110_136_41e.qk 3/4/2003 3:05 PM Page 138 PENTAX Corporation 2-36-9,Maeno-cho, Itabashi-ku, Tokyo 174-8639, JAPAN (http://www.pentax.co.jp/) PENTAX Europe GmbH (European Headquarters) Julius-Vosseler-Strasse, 104, 22527 Hamburg, GERMANY (HQ - http://www.pentaxeurope.com) (Germany - http://www.pentax.de) Pentax U.K. Limited Pentax House, Heron Drive, Langley, Slough, Berks SL3 8PN, U.K. (http://www.pentax.co.uk) Pentax France S.A.S.
