User manual

activated by the daylight sensor [23]. You can improve the quality of the
image at night by using additional illumination. The camera
automatically switches to black and white in low light conditions and in
artificial light.
If you want to install the camera outdoors, then protect the camera
against direct rainfall if possible. The mains adapter must be in a dry
location. The connection between camera and mains adapter cable must
be protected against moisture.
Ensure that there is a possible cable routing at the installation location.
The maximum range of the wireless signal is approx. 100 m (and up to
150 m in optimal conditions) with line of sight contact between camera
and monitor. Within buildings the range is greatly reduced by walls and
floors, in particular those made of steel reinforced concrete, to a
maximum of 20 m. Metal housings, shelves and mirrors also block the
wireless signal.
The wireless transmission can also be affected by strong electric fields
and other wireless equipment. Ensure an adequate distance of the
camera and receiver to microwave ovens, cordless phones, mobile
phones, wireless devices in the 2.4GHz frequency band, electric motors
and high voltage devices or power cables.
The monitor must be placed on a solid and level surface, ideally 1m
above the floor (optimal reception).
The camera can be wall or ceiling mounted (see fig. E: I and II).
For wall or ceiling installation mount the bracket [35] at a suitable
location using the screws [37] and if necessary the wall plugs [36]
provided.
Screw the bracket into the appropriate threaded hole in the camera
housing.
Adjust the angle ofthe camera to give the required view and then tighten
thewingscrew[33]andthescrewnut[34].
Turntheantenna[20]intoanuprightposition.
Connect the DC-plug of the mains adapter [27] to the mains adapter
connection[26]ofthecameracable.
Connectthemainsadapterwithasuitablemainsoutlet.
ThePOWERLED[28]lightsred.
Forportableuse,thecameracan bepoweredbybatteriesforupto 2hours.
Open the batterie compartment [32] and insert 3 pcs. AAA 1.5 V
alkaline batteries in correct polarity (see marking in battery
compartment). Switch thecameraoff[24] after portable use, and remove
thebatteriesbeforepoweringthecameraviathemainsadapter.
Foldoutthestand[8]tostandonalevelsurface.
Connect the DC-plug of the mains adapter cable [9] to the mains adapter
connectionofthemonitor[18].
Connectthemainsadapterwithasuitablemainsoutlet.
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
!
8. Installation and connection of the camera
9. Connectionofthemonitor
10. Operation
11.Basicfunction
!
!
!
!
!
!
!
!
!
!
!
!
!
!
Afterconnectionofthepowersupplythesystemisinoperation.
Removetheprotectionfoilfromthescreen[3].
To record video insert a readable and unlocked SD-card in the slot [6], if
the cardisnot formatted then format itbeforethe first use, as described in
chapter12.9.
Press the on/off button [7] on the monitor, the power-LED [11] lights
greenandthecamerapicturewillbedisplayedonthescreen.
TheLithium batterystarts chargingautomaticallywhen themains adapter
isconnected.Letthebatterychargefullybeforeportableuseofthemonitor
(withoutthemainsadapter).PayattentiontotheBatteryLED:
BatteryLED[10]lightsred: battery charge low; connect the mains
adapterwithasuitablemainsoutlet
BatteryLED[10]lightsgreen: battery charging, leave mains adapter
connecteduntilLEDgoesoff
BatteryLED[10]off: batteryischarged
Turntheantenna[2]intoaverticalposition.
To turn off the monitor hold the on/off button [7] pressed until "POWER
OFF"isdisplayed
Thesignalsfromamaximumof4camerascanbereceived.Thecamerawiththe
setisprogrammedinthefactorytochannel1(seeChanelindicator[39]).
The connection of the camera with themonitor is shownby the connectionLED
[29] on the camera whilst the reception indicator [38] on the screen displays
thereceptionqualitywithupto4bars.
Pressthedirectionbuttons[12: / ]toscrollthroughchannels1to4.
Selectthemonitorvolumeusingthedirectionbuttons[12: / ].
Press the record button[5]to start video and audio recording (recording is
splitinfilesofmax.30seconds).
Presstherecordbuttonagaintostoptherecording.
IftheScanPeriodisactivated,theimageofthecamerathatcanbeseenon
themonitorisrecorded.InQuadfunction,norecordingispossible.
Pressand hold the OK button[16]to be able to speak through thecamera
loudspeaker.Themicrophoneislocatedatthebottomleftofthemonitor.
Pressthelowerdirectionbutton[12]toswitchthelullabyon/off.
11.1 Wirelessconnection
11.2 ChannelSelection
11.3 Monitorvolume
11.4 Recording
11.5 Walkie-TalkieFunction
11.4 Lullaby
GB - 23