User's Manual

12
EasyTouch Wireless Control Panel Installation and User’s Guide
Synchronizing control panels
If the EasyTouch outdoor has been previously setup with specific pool and spa information and you install the
EasyTouch wireless control panel with factory default information, the outdoor control panel will automatically
download the existing system information to the wireless control panel. If the wireless control panel has a
different firmware revision level than the outdoor control panel or it contains previous setup information, you
can choose which system image to upload or download. Synchronizing the control panels is initiated from the
wireless control panel. The following describes how to synchronize the wireless control panel with the outdoor
control panel.
Download from outdoor to wireless control panel
• Press the Menu button to download the system image from the EasyTouch
outdoor control panel to the wireless control panel.
Upload to outdoor from wireless control panel
1. Press the Up/Down button to access the “Upload” screen.
2. Press the Menu button to upload the system image from the wireless control
panel to the EasyTouch outdoor control panel.
Note: To erase existing control panel system information, use the “Erase EEPROM” feature.
Refer to “Erase EEPROM” on page 51 for more information.
EasyTouch Menus
Unit Mismatch
Upload to
Outdoor
Unit Mismatch
Download from
Outdoor




MAIN SCREEN
LIGHTS
HEAT
POOL TEMP/SRC
TEMP (40˚ F - 106˚ F) OR (4˚ C - 41˚ C)
HEAT (OFF/HEATER/SOLAR/SOLAR PRF) - SOLAR/SOLAR PRF MUST BE ENABLED IN "SOLAR" MENU TO DISPLAY.
SPA TEMP/SRC
TEMP (40˚ F - 106˚ F) OR (4˚ C - 41˚ C)
HEAT (OFF/HEATER/SOLAR/SOLAR PRF) - "SOLAR/SOLAR PRF" MUST BE ENABLED IN "SOLAR" MENU TO DISPLAY.
DELAY CANCEL
MODE: SCHEDULE
08:00A -- 05:00P (12:00 AM - 11:59 PM -12 HOURS)
S M T W T F S (DAYS OF THE WEEK)
SCHEDULES
SPA 0
AUX 2 0
AUX 4 0
AUX 3 0
MODE: EGG TIMER
TIME: 12:00 (00:00 - 23:59) / DON'T STOP
SETTINGS
INTELLICHLOR
INTELLICHLOR 1/2 - ENABLE (YES/NO), POOL MODE: 0 - 100 % (50% default) SPA MODE: 0% (2% default)
INTELLICHLOR 2/2 - SUPER CHLR (ON/OFF), RUN HOURS (0 -72)
(OPTIONAL)
CIRCUIT NAMES
CIRCUIT NAMES (1/18) - [SPA, POOL, AUX 1-7 (ET8), AUX 1-3 (ET4), FEATURE 1-8, AUX EXTRA
CLOCK
DATE & TIME 1/2 - (MONTH/DAY/YEAR) - (DAY/HOUR/MINUTES/AM/PM)
DATE & TIMER 2/2 - DAYLIGHT SAVING: (AUTO/MANUAL)
CLOCK ADJUST 00:00 (0 TO 300) - (-300 TO -5) IN 5 SCEOND INCREMENTS
(DELAYED CANCELLED) PRESS RIGHT BUTTON TO ACTIVATE
POOL 0
AUX 1 0
AUX 5 0
AUX 6 0
AUX 7 0
EASYTOUCH 4
EASYTOUCH 8
MODE: ONCE ONLY
08:00A (12:00 AM - 11:59 PM -12 HOURS)
S M T W T F S (SELECT DAY OF THE WEEK TO RUN PROGRAM)
MODE: NEW / DELETE / NONE
HI-TEMP (SPA) / LO-TEMP (POOL) FOR SINGLE BODY SYSTEM (SEE SETTINGS MENU: CIRCUIT NAMES)
INTELLIFLO
(OPTIONAL)
FEATURE 1-8 0
AUX EXTRA: AUXILIARY OUTPUT (USE DOWN ARROW BUTTON TO SWITCH ON/OFF). ONLY AVAILABLE IF
SOLAR PLUG (J17) IF NOT BEING USED FOR SOLAR EQUIPMENT.
MODES [6 LIGHT SHOWS, HOLD, RECALL, COLOR SWIM, COLOR SET]
COLORS [5 FIXED COLORS, HOLD, RECALL, COLOR SWIM, COLOR SET]
ALL ON (SWITCH ALL LIGHTS ON)
ALL OFF (SWITCH ALL LIGHTS OFF)
SYNC (SYNCHRONIZE COLORED LIGHTS)
MAGICSTREAM [TOGGLE THUMPER, HOLD, RESET, CHANGE MODE]
CONFIG (SETUP EIGHT LIGHT POSITIONS)
FEATURE CIR
FEATURE 1-8 [OFF]
AUX EXTRA 0
FEATURE 1 - 8
MANUALLY TURN A FEATURE CIRCUIT ON/OFF.
USE FEATURE CIRCUITS TO CONTROL PUMP SPEEDS AND VALVES.
PUMP #1 - PUMP TYPE [VF, VS, VSF, NONE] - VF: FILTR. CIRCUIT, FLOW (GPM), FILTERING, PRIMING, BACKWASH, VAC
PUMP #2 - PUMP TYPE [VF, VS, VSF, NONE] - VS: SPEEDS (RPM), PRIMING, STATUS - VSF: FLOW/SPEEDS (RPM/GPM),
HEAT PUMP COM
SETTINGS: ENABLE, DISABLE (NO/YES) - [HEATING, COOLING] - STATUS
(OPTIONAL)
INTELLICHEM
PH/OPR Values (pH VAL, SET - OPR VAL, SET) - Status (pH/OPR level) - Saturation Index (CH,TDS,TA,SI)
(OPTIONAL)