User's Manual

15
EasyTouch Wireless Control Panel User’s and Installation Guide
EasyTouch Menu Structure
MAIN SCREEN
AUTO HEATER
SPA 100˚ F / 95˚F
AIR 70˚F
MON 09:30 AM
LIGHTS
All On (Switch all lights on)
All Off (Switch all lights off)
Sync (Synchronize colored lights)
HEAT
DIAGNOSTICS
Software Rev (Revision level for main control panel and Indoor Control Panel)
Bootloader Rev (Revision level for main control panel and Indoor Control Panel)
Self Test (Status: Testing (follow on-screen prompts to test LCD and buttons) - Code: 0 - see "Troubleshooting" section for error codes)
Water Temp (Fahrenheit/Celcius - Status display only)
Solar Temp (Fahrenheit/Celcius - Status display only) - (Displays if Solar is enabled in Heat menu)
Air Temp (Fahrenheit/Celcius - Status display only)
Pool Temp/Src
Temp (40˚ F - 106˚ F) or (4˚ C - 41˚ C)
Heat (Off/Heater/Solar/Solar Prf) - Solar/Solar Prf must be enabled in "Solar" menu to display.
Spa Temp/Src
Temp (40˚ F - 106˚ F) or (4˚ C - 41˚ C)
Heat (Off/Heater/Solar/Solar Prf) - "Solar/Solar Prf" must be enabled in "Solar" menu to display.
DELAY CANCEL
Mode: Schedule
08:00A -- 05:00P (12:00 AM - 11:59 PM -12 hours)
s m t w t f s (days of the week)
SCHEDULES
SPA 0
AUX 2 0
AUX 4 0
AUX 3 0
Mode: Egg Timer
Time: 12:00 (00:00 - 23:59) / DON'T STOP
SETTINGS
IntelliChlor
Enable (No/Yes)
Level (0% - 100%)
IntelliChlor 2/2
Run Hours (0 -72)
IntelliChlor 1/2
Super Chlr (On/Off)
(Optional)
Circuit Names
Circuit (Spa, Pool, AUX 1-3 (ET 4) - Spa, Pool AUX 1 - 7 (ET 8) Refer to "Circuit Names" on page 30
Circuit Names 1-9 (Assign names for up to 9 circuits)
Circuit Types
Circuit (Spa [MASTER SPA], Pool [MASTER POOL], AUX 1-7 (AUX 1-3), Generic, Master Spa, Master Pool, Mstr Cleaner,
Freeze: No/Yes
Custom Names
Cstm Name 1/10 (Assign up to 10 custom names)
[USERNAME-01...10] (up to 11 alphanumeric characters)
2-Speed Pump
Circuit (None, Spa, Pool, AUX 1 - 3 (ET 4) - Spa, Pool, AUX 1 - 7 (ET 8), Solar, Heater, Pool Heater, Spa Heater, Freeze)
2-Speed Pmp 1/4 (Assign up to 4 circuits)
Solar
Delays
Pool/Spa (Yes/No)
Valves (Yes/No)
Enable (Yes/No)
Heat Pump (Yes/No)
Solar 2/2 (Tempreature Difference)
Run (2˚-5˚)
Solar 1/2
Start (3˚-9˚)
Valves
Clock
F˚ / C˚
iS4
FAHRENHEIT / CELCIUS
Quick Touch
Assign QT4 1/4 (Assign up to 4 circuits)
Circuit - (None, Spa, Pool, AUX 1 - AUX 7 (ET 8), AUX 1 - AUX 3 (ET 4), HEAT BOOST, HEAT ENABLE)
Erase EEPROM
Erase all (Yes /No) - Are you sure? (Yes/No)
Circuit - (None, Spa, Pool, AUX 1 - AUX 7 (ET 8), AUX 1 - AUX 3 (ET 4), HEAT BOOST, HEAT ENABLE)
Assign iS4 1/4 (Assign 4 circuits)
Calibration
Air (Fahrenheit/Celcius)
Solar (Fahrenheit/Celcius) - Solar must be enabled in "Heat" menu to display
Water (Fahrenheit/Celcius)
Date & Time 1/2
June 22 2005 (Month/Day/Year)
WED 11:00 AM (Day/Hour/Minutes/AM/PM)
Date & Timer 2/2
Daylight Saving: (Auto/Manual)
Clock Adjust 00:00 (0 to 300) - (-300 to -5) in 5 sceond increments
(Delayed Cancelled) Press Right button to activate
A: [None, Spa, Pool, AUX 1 - 3 (ET 4) - Spa, Pool, AUX 1 - 7 (ET 8), Heater] - (USED SOLAR if Solar is enabled)
B: [None, Spa, Pool, AUX 1 - 3 (ET 4) - Spa, Pool, AUX 1 - 7 (ET 8), Heater]
Disp Op Codes - Display? No/Yes (Displays transmit/receive packets numbers on screen)
SPA SIDE [Off/On]
POOL 0
AUX 1 0
AUX 5 0
AUX 6 0
AUX 7 0
Enable/Disable iS4 Spa-Side remote
Light, SAM light, SAL Light, Photon Generator, Color Wheel, Spillway, Floor Cleaner (see page 32 for details)
Cir Names [On/Off] View default circuit names before modification.
Chlorinator
Salt Level: Displays current salt level (xxxx) ppm
Status: OK - NO ERRORS (SUPER CHLORINATE, COM LINK ERROR, CHECK FLOW / PCB,
LOW SALT, VERY LOW SALT, HIGH CURRENT, CLEAN CELL!!, LOW VOLTAGE)
Man Heat [Off/On]
Switch manual heat on or off when spa is manually switched on (Use Right button select On/Off)
EasyTouch 4
EasyTouch 8
Mode: Once Only
08:00A (12:00 AM - 11:59 PM -12 hours)
s m t w t f s (select day of the week to run program)
Mode: New / Delete / None
Reset System (Reinitialize Indoor Control Panel - use Right button)
Hi-Temp (Spa) / Lo-Temp (Pool) for single body system (see Settings Menu: Circuit Names)
Flash Update (Use for future firmware updates via PC - Press MENU to abort)
Power OFF (Manually switch's off the unit - Press the Power ON button to switch unit on)
Power Save Options
Idle Time: 30 S, 60 S, 5 M
Backlight Options
Brightness: LOW, MED HI
On Time: 30 S, 60 S, OFF