INSTALLATION MANUAL ® System 9760® KBD/KBR Firmware Upgrade CM9760-KBD-E80 C1543M-A (7/04)
INTRODUCTION The System 9760® keyboard upgrade kit, CM9760-KBD-E80, provides the following items to upgrade CM9760-KBD/CM9760-KBR firmware to version 8.03: 1 1 U3 EPROM chip, version 8.03, part number IC53-0043-0803 Chip extraction tool, part number ICPULLERTOOL This manual provides instructions to upgrade CM9760-KBD/CM9760-KBR firmware from version 7.8 or earlier to version 8.03. To upgrade CM9760-KBD firmware, see the section titled Upgrading CM9760-KBD Firmware.
UPGRADING CM9760-KBD FIRMWARE CAUTION: Only qualified personnel observing electrostatic discharge (ESD) precautions should perform the procedure below. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic components. Handle circuit boards by their edges. To upgrade CM9760-KBD firmware to version 8.03, do the following: 1. Using System Manager, upload user-entered keyboard setup information to the System Manager database.
6. Remove the existing U3 EPROM chip (refer to Figure 2) from its socket using the provided extraction tool. Remove the chip slowly to avoid damaging the socket. 7. Remove the replacement EPROM chip from the electrostatic bag, and inspect the chip to confirm that the pins are straight. 8. As illustrated in Figure 2, orient the chip using the alignment notch as a guide. Verify pin-to-socket alignment, and then carefully press the chip into its socket until the chip is completely seated. 9.
11. Calibrate the joystick as follows: a. In Setup mode, select the Joystick Adjust icon. The Joystick Setup menu appears (refer to Figure 3). KEYBOARD SELECT ICON FORWARD STEP/ SCROLL UP ICON BACKWARD STEP/ SCROLL DOWN ICON MOVE CURSOR/ MOVE CURSOR/ CYCLE SELECTIONS CYCLE SELECTIONS LEFT ICON RIGHT ICON EXIT ICON SAVE ICON Figure 3. Joystick Setup Menu b. c. d. e. f. g. h. i. j. k. l. m. With the joystick in the central default position, select the Keyboard Select icon.
UPGRADING CM9760-KBR FIRMWARE CAUTION: Only qualified personnel observing electrostatic discharge (ESD) precautions should perform the procedure below. Always wear a grounding strap connected to an approved grounding source when working on or near exposed electronic components. Handle circuit boards by their edges. To upgrade CM9760-KBR firmware to version 8.03, do the following: 1. Using System Manager, upload user-entered keyboard setup information to the System Manager database.
5. Locate DIP switch 7 on the rear of the KBR (refer to Figure 4), and set the DIP switch to the correct position: • For compatibility with CM9760-CC1 and CM9760-MGR versions 7.80.003 to 7.80.029, set DIP switch 7 to the OFF position. • For compatibility with CM9760-CC1 and CM9760-MGR version 8.03.006 or later, set DIP switch 7 to the ON position. 6.
12. Calibrate the joystick as follows: a. In Setup mode, select the Joystick Adjust icon. The Joystick Setup menu appears (refer to Figure 7). KEYBOARD SELECT ICON FORWARD STEP/ SCROLL UP ICON BACKWARD STEP/ SCROLL DOWN ICON MOVE CURSOR/ MOVE CURSOR/ CYCLE SELECTIONS CYCLE SELECTIONS LEFT ICON RIGHT ICON EXIT ICON SAVE ICON Figure 7. Joystick Setup Menu b. c. d. e. f. g. h. i. j. k. l. m. With the joystick in the central default position, select the Keyboard Select icon.
WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on the following fixed camera models: CC3701H-2, CC3701H-2X, CC3751H-2, CC3651H-2X, MC3651H-2, and MC3651H-2X.
® World Headquarters 3500 Pelco Way Clovis, California 93612 USA USA & Canada Tel: 800/289-9100 Fax: 800/289-9150 International Tel: 1-559/292-1981 Fax: 1-559/348-1120 www.pelco.
