I N S T A L L A T I O N Spectra® Mini Dome C3401M-D (3/09)
Contents Important Safety Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Regulatory Notices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Models . . . . . . . . . .
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7. Only use attachments/accessories specified by the manufacturer. 8.
Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class B digital device, pursuant to Part 15 of the FCC Rules.
Description The Spectra® Mini is an indoor dome system designed for ceiling applications. The dome can be mounted to the surface of ceilings, or it can be recessed in hard ceilings or standard 2 x 2 ft (61 x 61 cm) tiles in suspended ceilings. The Spectra Mini includes a high resolution color camera; video output capability through either coaxial cable or UTP wiring; pan/tilt control using Pelco D, Pelco P, or Coaxitron® protocol; and on-screen programming.
Before You Begin PACKAGE CONTENTS The following diagram shows the box contents. When installing the Spectra Mini dome, refer to this diagram. SPRING PADDLE FLEX ASSEMBLY DOME DRIVE TRANSLATOR BOARD COVER INTERFACE CABLE AND RJ45-10 CONNECTOR MACHINE SCREWS, #8-32 X 3.5-INCH 2 EA. TRIM RING AND BUBBLE INSTALLATION MANUAL OPERATION/PROGRAMMING MANUAL SELF-TAPPING SCREWS, 3.5-INCH, 1.5-INCH 2 EA. Figure 1.
SWITCH SETTINGS Coaxitron control: If you are going to use Coaxitron protocol to communicate with the dome system, you do not have to set any switches. Proceed to the installation instructions that follow this section. Non-Pelco control: If you are going to install a protocol translator board to communicate with the dome system through a non-Pelco controller, proceed to the installation instructions that follow this section.
Table A.
Table C.
Table C.
Table C.
Table C.
Table C.
Table C.
Table C.
WIRING TABLES Table D. Video Coaxial Cable Requirements Cable Type* Table E.
Installation SURFACE MOUNT 1. On top of the dome drive is an opening for an optional translator board. The opening has a cover that must remain in place if a translator board is not required. A taller cover is supplied if a translator board is installed. If you are going to install a translator board, follow the instructions that come with the translator board. If you are not going to install a translator board, save the taller cover in case you ever choose to install a translator board. 2.
c. Drill a hole in the ceiling for wiring; pull all wiring through the hole and terminate all wires (if not already terminated). NOTE: You do not have to run wiring through the ceiling; you can fasten the wires to the ceiling and then run the wires through the gap between the ceiling and the surface mount ring (refer to Figure 5). Figure 5. Wiring Attached to Ceiling 3.
RECESSED 1. On top of the dome drive is an opening for an optional translator board. The opening has a cover that must remain in place if a translator board is not required. A taller cover is supplied if a translator board is installed. If you are going to install a translator board, follow the instructions that come with the translator board. If you are not going to install a translator board, save the taller cover in case you ever choose to install a translator board. 2.
5. Cut a 5-inch diameter hole in the ceiling tile. You can either use the two holes in the spring paddle flex assembly as a compass tool to mark the 5-inch diameter hole, or use a 5-inch hole saw. 6. If you are wiring more than one dome drive to the same transformer, connect one side of the transformer to pin 9 of the RJ45-10 connector on all modules. Connect the other side of the transformer to pin 10 of the RJ45-10 connector on all modules.
Figure 9.
Maintenance DATA PORT The data port (refer to Figure 10) allows access for on-site setup and testing of the dome system. It also is used for uploading revised operating software and language files. Refer to Software/Language File Upload in the Operation/Configuration manual. Figure 10.
Specifications MECHANICAL Pan Movement 360° continuous pan rotation Vertical Tilt Unobstructed +2° to -92° Manual Pan/Tilt Speeds Pan Tilt 0.4 to 80°/sec manual operation, 100°/sec turbo 0.7 to 40°/sec manual operation Preset Speeds Pan Tilt 140°/sec 80°/sec For variable speed operation an appropriate controller is required. ELECTRICAL Input Voltage 18 to 30 VAC, 24 VAC nominal Input Power 21 VA nominal Fuse 1.
Shutter Speed Automatic (electronic iris)/manual 1/60~1/30,000 Gain Control Automatic with manual override Video Output 1.0 to 1.2 Vp-p, 75 ohms, adjustable Video Signal-to-Noise Ratio >50 dB LENS Lens f/1.8 (4.2~42 mm optical) 10X optical zoom, 8X digital zoom Zoom Speed (optical range) 1.5/2.5/4.3 seconds Horizontal Angle of View 46.4° wide zoom 5.
For surface mount installations with a translator board, use this template (refer to Surface Mount on page 17). WARNING: Before printing this document, your printer must be set for 100% scaling. The diameter of the circle is 4.7 inches (11.95 cm). Printing the template at an incorrect scale could result in equipment damage. Figure 11.
C3401M-D (3/09)
PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment.
www.pelco.com Pelco, Inc.
