® SB19/SB1900 Series Discreet Surveillance Enclosures Installation/Operation Manual C467M-D (5/95) Pelco • 3500 W. Pontiac Way, Clovis, CA 93612-5699 • USA • www.pelco.
TABLE OF CONTENTS Section Page 1.0 2.0 3.0 4.0 WARNINGS ........................................................................................................................................ 1 SCOPE ............................................................................................................................................... 2 DESCRIPTION ................................................................................................................................... 2 INSTALLATION ...
INSTALLATION AND OPERATION MANUAL DISCREET SURVEILLANCE ENCLOSURES: MODEL SB19/SB1900 SERIES MODEL SB19-1/SB1901 SERIES MODEL DD1900 SERIES CAUTION This device is designed to operate at 24VAC power. Input voltage must not exceed 28 volts or drop below 22 volts or else damage to the motors will occur. Should you need assistance with this or any Pelco product, please call 1-800-298-9100 or 1-559292-1981. 1.0 WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed.
2.0 SCOPE The information contained within this manual covers the SB19/SB1900 Series of Discreet Surveillance Enclosures. NOTE: The following are the cable requirements. A relay box (RB24) is available to extend the operating distance. Consult the factory for details. 3.
Figure 1.
4.3 MOUNTING INSTRUCTIONS 2. Determine the type of mounting desired. The enclosure can be mounted in a hard ceiling, completely replace a standard 2' x 2' suspended ceiling tile using the APSB19 optional faceplate, or be inserted through a cut-out in a standard 2' x 2' suspended ceiling tile. Remove the factory assembled 12.5" round faceplate from the back box by disengaging the serrated studs. 3. Remove the factory assembled 14.5" square mounting plate by removing the four (4) 1/4-20 bolts. 4.
. 8. 9. Slide the back box through the ceiling tile and mounting plate and replace the four (4) 1/4-20 bolts and tighten to secure the back box to the mounting plate.
13. Attach the dome to the pan/tilt by aligning the two ball studs protruding through the flange of the dome with the two holes in the dome attachment brackets and engaging the studs. 14. Attach the safety chain on the side of the back box to the short 4-40 threaded screw in the 12.5" round faceplate trim with the provided hardware. 15. Attach the faceplate trim to the back box by aligning the two serrated studs with two of the holes in the edges of the back box and engaging the studs. 16.
4.3.1.2 Suspended Ceiling Tile Replacement Mounting template. Also, the lens must not project higher than the long end of the template. To mount the enclosure into a suspended ceiling grid where the tile is replaced, perform the following steps. NOTE: If the camera and lens do not fit within the boundaries of the template, they will not fit inside the dome and need to be replaced with smaller units. 1. Determine the location for mounting the enclosure and remove the appropriate ceiling tile. 8.
12. Attach the safety chain on the side of the back box to the short 4-40 threaded screw in the 12.5" round faceplate trim with the provided hardware. 6. 13. Attach the faceplate trim to the back box by aligning the two serrated studs with two of the holes in the edges of the back box and engaging the studs. 14. Operate the pan/tilt to verify that there are no obstructions or dragging cables within the back box or dome.
12. Attach the faceplate trim to the back box by aligning the two serrated studs with two of the holes in the edges of the back box and engaging the studs. 2. Pan to the desired left position, remove the drive unit from the back box and adjust the pan limit stop until the actuator clicks, and lock into position. Replace the drive unit. 13. Operate the pan/tilt to verify that there are no obstructions or dragging cables within the back box or dome. 3.
5.0 CARE AND MAINTENANCE Regularly scheduled maintenance will prolong the operational life and appearance of the equipment. IMPORTANT: The lower dome of the enclosure is an optical surface. When cleaning the inner surface of the dome and viewing window, treat as carefully as you would a fine camera lens. Do not use water, liquid or spray cleaners of any kind on coated inner surface of dome. If dust or other debris accumulates on the inside of the lower dome, remove with clean air pressure only.
6.0 EXPLODED ASSEMBLY DIAGRAM Refer to Figure 7 for an exploded assembly diagram of the SB19 enclosure. * PP ONLY ** NON SL ONLY EXPASB1900 EXPASB1900PP Figure 7.
7.0 EXPLODED ASSEMBLY MECHANICAL PARTS LIST Item Qty 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 1 1 1 1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 4 2 2 6 2 1 1 1 1 2 1 1 2 1 4 2 1 1 12 Description Pelco Part Number UL, Pad, camera, black .062" thick PCB assembly, pan/tilt Bushing, 3/8" tilt shaft Shaft, tilt table Sprocket .
7.0 EXPLODED ASSEMBLY MECHANICAL PARTS LIST (continued) Item 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 thru 70 71 72 73 74 75 76 77 78 79 80 Qty 1 1 1 1 2 2 1 1 2 1 3 1 1 1 1 Description Not used Not used Not used Slip ring, 24 circuit for presets Not used Not used Not used Bracket, tilt pot Bracket, LPP lens connector Gear, 1.875 plastic Gear, 1.
8.0 MODELS DD1900 Dome drive unit for SB1900. (UL) DD1900-PP Dome drive unit for SB1900-PP. DD1900-SL Dome drive unit for SB1900-SL. (UL) DD1900SL-PP Dome drive unit for SB1900SL-PP. SB19 Drop ceiling discreet surveillance enclosure with black opaque lower dome with less than 1 f-stop light attenuation and all aluminum back box which mounts above the ceiling. (Camera mount supplied.
9.2 MODELS SB1900, SB1900-SL, SB1900-PP AND SB1900SL-PP IOP19B1C B/W NTSC 6X camera and lens pkg. with preset positioning. CM7500 Series Coaxitron Matrix Switcher/Control System rack mount card cage with CPU and power supply. Capable of up to 64 inputs and up to 4 monitor outputs. (See C584 product specification sheet for details). IOP19B1G B/W NTSC 10X camera/lens pkg. IOP19C1B Color NTSC 6X camera and lens pkg. IOP19C1C Color NTSC 6X camera and lens pkg. with preset positioning.
Pan Speed: 24°/sec ± 1° Tilt: -90° movement from horizontal plane Tilt Speed: 12°/sec ± .5° Lens Connector: Hirchmann 6100 type (mate supplied) for non-PP models AMP CPC type (mate supplied) for PP models Motors: Synchronous type, continuous duty, instantaneous reversing Maximum Load: 10 lbs (4.
12.0 WARRANTY AND RETURN INFORMATION WARRANTY RETURNS Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: In order to expedite parts returned to the factory for repair or credit, please call the factory at (800) 289-9100 or (559) 292-1981 to obtain an authorization number (CA number if returned for credit, and RA number if returned for repair).
Pelco 3500 Pelco Way • Clovis, CA 93612-5699 (559) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (559) 292-3827 International customers call 1-559-292-1981 or FAX 1-559-348-1120 (Product specifications subject to change without notice.
