Sarix® Professional 3 Series IMP IBP IXP IWP Indoor Environmental Indoor ABF Box Rugged Environmental IR Bullet Environmental Vandal Dome Wedge Dome IMP131-1ERS IBP131-1ER IXP13 IWP133-1ERS IMP231-1ERS IBP231-1ER IXP23 IWP233-1ERS IMP331-1ERS IBP331-1ER IXP33 IWP232-1ERS IMP231-1IS IBP531-1ER IXP53 IWP234-1ERS IMP331-1IS IBP232-1ER IWP236-1ERS IMP531-1ES IBP532-1ER IWP333-1ERS IMP531-1IS IBP235-1ER IWP532-1ERS IMP231-1ES IBP335-1ER IWP533-1ERS IMP331-1ES IMP131-1IRS IMP231-1
Contents Important Notices ......................................................................................................................................................................... 4 Regulatory Notices [FCC CLASS A] .................................................................................................................................... 4 Radio and Television Interference ...............................................................................................................
2.2.5 Event Source .................................................................................................................................................... 56 2.2.6 Event Handler................................................................................................................................................... 63 Pelco Troubleshooting Contact Information ...............................................................................................................................
Important Notices REGULATORY NOTICES [FCC CLASS A] This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules.
OPEN SOURCE SOFTWARE This product includes certain open source or other software originated from third parties that is subject to the GNU General Public License (GPL), GNU Library/Lesser General Public License (LGPL) and different and/or additional copyright licenses, disclaimers, and notices. The exact terms of GPL, LGPL, and some other licenses are provided to you with this product. Please refer to the exact terms of the GPL and LGPL at http://www.fsf.org (Free Software Foundation) or http://www.
Preface This operations manual is to be used as a reference for the manipulation of the camera unit including features, functions, and a detailed explanation of the menu tree. This manual provides the following information: 6 Administration and Configuration: The main menu navigation and controls explanations.
1. Installation and Connection 1.1 Installation 1.1.1 Network Topology The unit, which is equipped with Ethernet RJ-45 network interface, can deliver video images in real time via either Internet or Intranet. Please refer to the skeleton drawings shown below to aid your understanding. FIGURE 1-1: NETWORK TOPOLOGY 1.1.2 System Requirements The table below lists the minimum requirements to implement and operate a unit.
Note 1. All the installation and operations should comply with your local electricity safety rules. 2. This product is not compatible with QuickTime version 7.6.4 for Windows XP or Windows Vista. If you have this version installed on your PC, you will need to upgrade to QuickTime version 7.6.5. 3. Network and processor bandwidth limitations might cause the video stream to pause or appear pixelated when additional Web-interface users connect to the camera.
1.2 Connection 1.2.1 Default IP address The unit’s default IP address is 192.168.0.20 and sub mask is 255.255.255.0. When setting default IP address of 192.168.0.20 the camera will check to see if that address is already in use and will bump the last octet of the address by 1 if it is. The bump last octet of IP Address by 1 will continue until an unused IP address is found.
NOTE: When connecting to the camera for the first time, or after restoring the camera’s setting back to factory default, a user account must be created to enable access to video from the camera. FIGURE 1-3: USER CREATION 1.2.2.3 Viewing Preparation Images of the unit can be viewed through Microsoft Internet Explorer 9 or later. Before viewing, follow these steps to enable the display. 1. Enable Cookies On the Privacy tab, move the settings slider to Low or Accept All Cookies. 2.
2. Administration and Configuration 2.1 Live Simply click on Live on the top right side of the browser window while accessing the IP address of the unit, and a live video is displayed directly in the browser window. When clicked on Settings, a window will pop up for configuring “System”, “Network & Security”, “Imaging”, “A/V Streams”, “Event Source” and “Event Handler”. Please refer to 2.2 Settings on page 13 for more information. The current logged in identity appears to the right of the Help.
2.1.1 Zoom and Focus Controls Zoom Zoom In: Click and drag the slider right to zoom the lens in. Zoom Out: Click and drag the slider left to zoom the lens out. Focus Full Range Auto-Focus: Click the button for the camera to start a full-range search to find the optimal focal point for the scene. Quick Auto-Focus: Click the button for the camera to start a quick search to find the optimal focal point for the scene. NOTE: The Zoom function is available in motorized models only. 2.1.
2.1.3 Video Analytics Control Draw Object Bounding Draw Object Bounding: Check this box to allow camera to activate motion detection and draw an area around the detected object. This function can be use only when a VA function is activated. Video Analytics Select a Video Analytics (VA) function from the dropdown menu. Make sure that the selected VA function is enabled in “Event Source” section. When “Off” is selected, it means that the camera is not performing any VA function.
2.2.1 System Use the System tab to change the device name, configure the time settings, set up the text overlay for the live view, get backup, display system information, update firmware version, get information about inserted SD card and pixel count. You can also use the System tab to generate a system log, reboot the camera, or to restore the camera's factory default settings. FIGURE 2-4: SYSTEM SETTINGS Generate System Log 1. Click the System tab. 2.
2. Click the Restore All Camera Defaults button to restore the camera’s factory default settings. NOTE: If the camera is not connected to a Dynamic Host Configuration Protocol (DHCP) network, the IP address settings for the camera will be lost and the server will not recognize the camera. DHCP On is the default setting for the camera IP address. 2.2.1.1 General Settings FIGURE 2-5: GENERAL SETTINGS Device Name To change the Device Name, follow these steps: 1.
2. Select the Time Zone option. Select the continent and the region that are closest to the camera’s location from the Time Zone drop-down menus. NOTE: If your location observes a form of daylight saving time, the system will automatically change the time on the associated dates. 3. Select the format in which the date and time will appear from the Display Format drop-down field if you have opted to show the Date/Time Overlay. 4.
2.2.1.3 Firmware System Information The System Information page fields are read-only and include the firmware version, hardware version, model number, and serial number of the system are revealed here as below figure. This information is typically required by Pelco Product Support for troubleshooting purposes. FIGURE 2-7: SYSTEM INFORMATION Firmware Update Users can update system firmware if available. Ensure a user has been created before updating camera’s firmware.
2.2.2 Network & Security Use the Network tab to change the camera’s general network settings, select the Transport Layer Security(TLS) settings, enable Secure Shell (SSH), configure 802.1x port security settings, choose SNMP Server, Firewall mode, enable FTP access to this camera, activate RTP stream settings and VMS Connectivity with the specific server. NOTE: Other underlying protocols such as NTCIP 1205, ARP, RTCP, and WS-Discovery are supported by all models. NOTE: Enabling SNMP protocol (refer to 2.2.
HTTP Port NOTE: The HTTP port number must remain at the default setting (80) when connecting to a Pelco video management system (VMS) platform. If connecting to a Pelco VMS, do not change the HTTP port setting. 1. Click in the HTTP Port box and highlight the text. 2. Type the new port number in the HTTP Port field. The default port for HTTP communications is 80. 3. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.
Configuring IPv6 Settings Your Sarix device supports IPv6 in conjunction with IPv4 configurations; the device does not support IPv6-only network deployments. The device will accept up to sixteen IPv6 addresses, three IPv6 DNS servers, and three IPv6 gateways. There are two configuration modes for IPv6 address assignments: Auto: Enables automatic configuration using router advertisement. Additional configuration can be provided over DHCPv6 (if available on your network).
FIGURE 2-11: USERS & SECURITY Creating a New User Click New User button below the left box and Select the Access Level for the new user. Access Level 1. Select the Access Level for the user. Admins: This is the only defined group that cannot be deleted. This group has access to all permissions. Managers: This defined group can be modified or deleted. This group has access to all permissions except the Operators: This defined group can be modified or deleted.
2. Click the Delete User button. A dialog box appears with the message “Are you sure you want to delete this user?” 3. Click OK. The user profile is deleted from the defined user profiles section. NOTE: The default “admin” user cannot be deleted.
NOTE: If the TLS mode is set to disabled, you cannot access the camera using a URL that begins with an “https:” protocol. Your Web browser displays an error message if you do not type the camera URL correctly. Refer to the following sections for more information: • Generating Self-Signed Certificate • Generating Certificate Request Certificate Generating Self-Signed Certificate 1. Click the Install New Certificate button located at the bottom of the TLS Configuration page.
FIGURE 2-15: GENERATING CERTIFICATE REQUEST 3. Fill in all of the fields, and then click Generate Request. The following progress message appears on the page: “Generating certificate signing request, please wait…” 4. Send the CSR, which looks like an encrypted block of undecipherable text, to a third-party certificate authority of your choice for a signature. 5. After you receive the signed certificate, click the Install Certificate button to upload the signed certificate to the device. 6.
2.2.2.4 SSH SSH is a user-enabled protocol that allows Pelco Product Support to log on to and service the camera for advanced troubleshooting purposes. From this page, users with the appropriate permissions can enable or disable SSH access to the camera. FIGURE 2-17: ENABLING SECURE SHELL SSH Settings 1. Select the Enabled check box. 2. Click in the Password box and type a password (4 to 16 alphanumeric characters). Passwords are case-sensitive.
methods include EAP-MD5, EAP-TLS, EAP-TTLS, and EAP-PEAP. 3. Type the information required for the selected 802.1x authentication method. 4. Connect the PC to an 802.1x secured switch that has the same EAP method. 5. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. 2.2.2.6 SNMP SNMP is an application layer protocol used to manage TCP/IP-based networks from a single workstation or several workstations.
4. Select the privacy encryption algorithm setting from the Privacy drop-down menu: None, DES, or AES. If you use privacy method DES or AES, type a password in the text box to the right of the selected Privacy encryption. 5. Configure the address for the Trap Configuration. The Address is the host name or IP address of the recipient of the trap message. 6. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it.
2.2.2.7 Firewall Set the Firewall function. A firewall is a system or group of systems that manages access between two networks. FIGURE 2-20: FIREWALL CONFIGURATION Firewall 1. Select Allow or Deny mode to enable this function. The default setting is Off. 2. Check Enabled to enter IP address in the Address field. Up to ten addresses can be enabled for entry. 3. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. 2.2.2.
4. Re-type Password to confirm it. 5. Set the number of maximum connections by entering a number in the Max Connections field. NOTE: This is the maximum of FTP Client connections, not the maximum of IE Window’s connections. 6. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. 2.2.2.
FreeDNS: A DDNS provider offering free service. Please register yourself before enabling this type. Hostname: Define a specific hostname for DDNS. Username: Configure a privileged username for accessing to DDNS. Password: Input the password associated with the privileged username. 2.2.2.11 SIP Session Initiation Protocol (SIP) is a text-based protocol, similar to HTTP and SMTP, for interactive communication sessions between users; allowing sessions with voice and video elements.
2.2.3 Imaging Use the Imaging tab to change the camera’s general image settings, adjust the camera exposure and white balance, program the focus mechanism, or define window blanking privacy areas. FIGURE 3-26: IMAGING SETTINGS 2.2.3.1 General General imaging settings include adjustments for camera orientation and digital processing. FIGURE 2-25: GENERAL IMAGING SETTINGS Orientation Use this setting when installing the camera in an inverted position.
increase the contrast; move the slider to the left to decrease the contrast. The range of adjustment is –100 to 100; the default setting is 0 (zero). Brightness: Controls the lighting detail in a scene. Move the slider to the right to lighten the image; move the slider to the left to darken the image. The range of adjustment is –100 to 100; the default setting is 0 (zero). Hue: Controls the color in a scene.
2.2.3.2 Exposure Exposure is the amount of light detected by the camera sensor. A scene with correct exposure settings has adequate detail and contrast between white and dark values. An image with too little or too much exposure eliminates detail in the scene. The camera features Exposure and Day/ Night settings. FIGURE 2-26: EXPOSURE SETTINGS Exposure Priority Preset Select Motion or Low Noise as the exposure priority. The Motion setting increases exposure time to reduce motion blurring in low light.
wished to view, resulting in the area being too dark and difficult to see. In this case, users may set the area corresponding to the portion they wish to see. FIGURE 2-27: BLC SETTINGS ILLUSTRATIONS DC Iris Control DC Iris Control, driven by electric currents, is one of the auto iris modes that helps the surveillance camera to automatically adjust its iris opening, for better adaptation to environments with constant changes in light levels. There are 2 options below for selection: 1.
TABLE 2-1. LUX TRANSITION POINTS FOR INCANDESCENT LIGHTING Transition Level Day to Night Setting Transition Point Lighter 10 lux Default 2 lux Darker 1 lux Check the IR Illumination box to enable IR Illumination. NOTE: The IR Illumination function is available in IR equipped models only. 2. Transition Detect Time (sec): Controls the length of time the camera is exposed to a light level before it changes to color or black-white mode.
None Iris When the mounted lens does not support either DC Iris or P Iris functionalities. This option is the entry selection for common lens type without advanced iris control mode. DC Iris Once DC Iris is selected, the DC Iris Control above will appear for iris adjustment. P Iris It is required to choose a compatible lens model from the dropdown menu once P Iris is selected. The P Iris Control above will appear for adjustment correspondingly.
FIGURE 2-30: FOCUS SETTINGS Focus Auto Focus 1. Temperature Change Refocus: The camera is programmed to run a quick automatic focus sequence when the internal temperature sensor of the camera detects an environmental temperature change of 41°F (5°C). This focus sequence adjusts the center focal point of the scene to maintain optimal focus. The default setting is Off; select On to turn on this setting. 2. Day/Night Switch Refocus: The default setting for the Day/Night Switch Refocus is Off.
FIGURE 2-31: MANUAL FOCUS SETTINGS 1. Day Manual Focus Position: If you need to fine-tune the daytime focus, slightly move the Day Manual Focus Position slider to the left or right. 2. Night Manual Focus Position: If you need to fine-tune the nighttime focus, slightly move the Night Manual Focus Position slider to the left or right. 3. If required, click the Restore Settings to Defaults button to reset the focus to the factory default setting.
2.2.3.4 White Balance Under White Balance, choose from ATW (auto tracing white balance), Auto, and Manual modes of adjustment on white balance for the video. ATW enables automatic controls on color temperature ranging from 2500°K to 10000°K. Auto offers continuous adjustments on camera color balance in accordance with any change in color temperature.
2.2.3.5 Window Blanking Window blanking is used to conceal user-defined privacy areas. A blanked area appears on the screen as a solid gray window. The camera can handle up to 8 blanked windows as long as the total blanked area does not exceed 50 percent of the field of view. FIGURE 2-34: WINDOW BLANKING SETTINGS Window Blanking Window Blanking On 1. Draw a window in the Live Preview area of the page: a Hold down the left mouse button. b Drag the mouse diagonally across the area you want to blank.
NOTE: Up to 8 blanked windows can be defined, but the blanked area cannot exceed 50 percent of the field of view. 2. To resize the window, click and drag one or more of the points until the window is the desired shape and size. 3. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. Deleting a window blanking area 1.
2.2.4 A/V Streams Use the A/V Streams tab to configure the video and audio streams for the camera. The A/V Streams tab includes the Video Configuration page, the Audio Configuration page, the Local Recording page, the RTP Settings page, and the Smart Compression page. 2.2.4.1 Video Configuration The Video Configuration page allows you to customize the compression, resolution, rate control, image rate, GOP length, Qos codepoint, Endura Signing, and profile of the video streams.
FIGURE 2-36: CUSTOM VIDEO STREAM CONFIGURATION Select Preset Presets are fully-configured video configurations that offer a good balance of video performance to bandwidth. These presets may also be used as a starting point for a custom configuration. Choose to switch the Corridor Mode On or Off. Corridor Mode offers a vertically widened field of view in narrow spaces like hallways and tunnels. NOTE: Corridor mode is not available when codec is MJPEG.
High: Typical high bandwidth settings creating high quality images. Medium: Typical decent bandwidth settings creating decent quality images. Low: Typical low bandwidth settings creating low quality images. Custom: User specified settings for Primary, Secondary and Tertiary Streams allowing selection of Aspect Ratio of 3:4 or 16:9, and selection of Maximum Frame Rate of 30 ftp (WDR) or 60 ftp (No WDR). Primary Stream Select Custom in Select Preset and configure Primary Stream.
TABLE 2-2.
Resolution Aspect FPS ratio Single Dual stream Triple stream 2048x1536 + 2048x1536 2048x1536 + 2048x1536 + 1280x960 stream 2048x1536 + 2048x1536 + 800x600 2048x1536 + 2048x1536 + 640x480 2048x1536 + 2048x1536 + 320x240 2048x1536 + 1600x1200 2048x1536 + 1600x1200 + 1600x1200 2048x1536 + 1600x1200 + 640x480 2048x1536 + 1600x1200 + 320x240 2048x1536 + 1440x1080 2048x1536 + 1440x1080 + 640x480 2048x1536 + 1440x1080 + 320x240 3M**** 4:3 30 2048x1536 2048x1536 + 1280x960 2048x1536 + 1280x960 + 1
Resolution Aspect FPS ratio Single Dual stream Triple stream 1920x1080 + 1920x1080 1920x1080 + 1920x1080 + 1920x1080 stream 1920x1080 + 1920x1080 + 1280x720 1920x1080 + 1920x1080 + 640x360 1920x1080 + 1920x1080 + 320x180 1920x1080 + 1280x720 2M**** 16:9 60/30/30 1920x1080 + 1280x720 + 1280x720 1920x1080 1920x1080 + 1280x720 + 640x360 1920x1080 + 1280x720 + 320x180 1920x1080 + 640x360 1920x1080 + 640x360 + 640x360 1920x1080 + 640x360 + 320x180 1920x1080 + 320x180 1920x1080 + 320x180 + 320x18
Resolution Aspect FPS ratio Single Dual stream Triple stream 1280x720 + 1280x720 1280x720 + 1280x720 + 1280x720 stream 1280x720 + 1280x720 + 640x360 1280x720 + 1280x720 + 320x180 1M**** 16:9 60/30/30 1280x720 1280x720 + 640x360 1280x720 + 640x360 + 640x360 1280x720 + 640x360 + 320x180 1280x720 + 320x180 1280x720 + 320x180 + 320x180 2048x1536 + 1600x1200 + 640x480 3M*** 4:3 30/15/30 2048x1536 2048x1536 + 1600x1200 2048x1536 + 1600x1200 + 320x240 2048x1536 + 1280x960 2048x1536 + 1280x960
Resolution Aspect FPS ratio Single Dual stream Triple stream 1280x960 + 1280x960 1280x960 + 1280x960 + 1280x960 stream 1280x960 + 1280x960 + 800x600 1280x960 + 1280x960 + 640x480 1280x960 + 1280x960 + 320x240 1280x960 + 800x600 1.
Resolution Aspect FPS ratio Single Dual stream Triple stream 1280x960 + 1280x960 1280x960 + 1280x960 + 800x600 stream 1280x960 + 1280x960 + 640x480 1280x960 + 1280x960 + 320x240 1280x960 + 800x600 1.
Resolution Aspect FPS ratio Single Dual stream Triple stream 1280x960 + 1280x960 1280x960 + 1280x960 + 800x600 stream 1280x960 + 1280x960 + 640x480 1280x960 + 1280x960 + 320x240 1280x960 + 800x600 1.
CBR: The constant bit rate (CBR) streams video at a fixed number of bits per second. CBR uses the full capacity of the bit rate setting for scenes with or without motion. Video is always streamed at the user bit rate setting. Adjust the CBR Bit Rate slider that appears when CBR is selected to the optimal fixed number of bits per second.
Tertiary Stream Select Custom in Select Preset and configure Tertiary Stream. Repeat Primary Stream setting steps for the Tertiary Stream settings. 2.2.4.2 Audio Configuration The Audio Configuration page allows you to setup the audio device. The default setting for Audio is disabled, which means that no audio is transmitted from the camera. When enabled, audio is transmitted from the camera to the PC. Based on your system configuration, images and audio may not be synchronized.
2.2.4.3 Local Recording Local Recording enables users to record and save video files locally on the SD card inserted, instead of recording and saving them over the network that will occupy a huge portion of memory and bandwidth. Check to enable this type of recording. Note that once the card is full, the oldest and previously-recorded video files on the card will be overwritten when the option “Enable Continuous Recording” is checked. FIGURE 2-38: LOCAL RECORDING 2.2.4.
Time to Live (TTL): Set the effective scope of multicast distribution for RTP video streaming between 1 and 255. TTL is a mechanism that limits the lifespan of data in a computer or network. It is implemented by having a counter or timestamp attached or embedded in the data in order to ensure that data is discarded once the correct time is reached. TTL counter decrements each time the signal pass through a router, so when the value reaches 0, the signal can no longer be distributed.
FIGURE 2-40: H.264 PELCO SMART COMPRESSION Smart Compression Level Smart Compression swiftly identifies dynamic motions occurred within a scene and retains its details with clear quality, whereas the rest areas, e.g. static background, will be imposed on higher compression level, thus economically decreasing bandwidth wielding on less important things and still keeping the dynamic motions details for future forensic purpose.
Normally Open: An alarm will be triggered when the external contact closes. Normally Closed: An alarm will be triggered when the external contact opens. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. NOTE: The Alarm Source function is available in Alarm equipped models only. 2.2.5.
FIGURE 2-43: MOTION ZONE AREA ENABLING 5. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. 2.2.5.3 Sabotage Detection The Camera Sabotage behavior detects scene changes or contrast changes in the field of view. An event or alarm is triggered if the lens is obstructed by spray paint, a cloth, or if it is covered with a lens cap. Any unauthorized repositioning of the camera also triggers an event or alarm.
FIGURE 2-45: AUDIO DETECTION 2.2.5.5 Object Counting The Object Counting behavior counts the number of objects that enter a user-defined zone. This behavior can be used to count people at a store entrance/exit or inside a store where the traffic is light. It might also be used to monitor vehicle traffic on highways, local streets and roads, parking lots, and garages. FIGURE 2-46: OBJECT COUNTING SETTING Object Counting 1.
When High is selected Object Counting is activated with slight changes in brightness or motion. On the contrary, when Low is selected Object Counting is activated with big changes in brightness or motion. 6. Click the Save button to save the settings. 7. Switch to the Live View page and select Object Counting from the Video Analytics dropdown menu. When there is a moving object traveling through the designated line, the number coming along with the arrow and line will increase (“1” shown in the image).
when Low is selected Adaptive Motion is activated with big changes in brightness or motion. 6. Click the Save button to save the settings. 7. Switch to the Live View page and select Adaptive Motion from the Video Analytics dropdown menu. When there is a moving object crossing the designated line as the above image, both the crossed borderline and the rectangular frame enclosing the moving object are highlighted with red color for distinctive identification.
2.2.6.8 Directional Motion The Directional Motion behavior generates an alarm in a high traffic area when a person or object moves in a specified direction. Examples of typical installations for this behavior include airports, entrances and exits, and vehicle traffic through tunnels. In an airport installation, cameras observe passengers boarding a plane in a terminal. If a person moves in the opposite direction of the normal flow of traffic, an alarm triggers.
2.2.6 Event Handler 2.2.6.1 FTP Upload Handler Under this page, the camera can record and send snapshot files via properly predefined FTP settings for different events composed of Alarm, Zone, Sabotage, Schedule, Audio Detection, Object Counting, Adaptive Motion, Object Removal, as well as Directional Motion. FIGURE 2-50: FTP UPLOAD HANDLER FTP Upload Handler You can record and send event image files based on the condition you have set previously. 1.
FIGURE 2-51: SNAPSHOT NAMING You can also set Trigger Interval time and determine the recording condition: OFF, All Day, Schedule 1, or Schedule 2 from scheduled table during 24/7 for Schedule. The trigger interval can be adjusted on a scale bar with its corresponding seconds shown in the box underneath. FIGURE 2-52: FTP UPLOAD HANDLER SCHEDULED SETTINGS 2.2.6.2 Relay Open/Close Handler Define the relay related settings for alarm output device when a selected event is triggered under this page.
FIGURE 2-53: RELAY OPEN/CLOSE HANDLER SETTINGS Relay Open/Close Handler 1. Check any or all of the Alarm, Motion 1 through 4, Sabotage Detection, Audio Detection, Object Counting, Adaptive Motion, Object Removal, as well as Directional Motion options from the Enabled section to activate relay handler when any of the selected events occur. 2. Select Normally Open or Normally Close from the drop-down menu of Polarity for the relay handler. 3.
2.2.6.3 SD Record Handler Save video clip backups from a variety of activated events to an SD card. Before using this function, a SD card must be installed in the camera beforehand. NOTE: The SD card must be formatted as FAT32. Other formats are not compatible with the camera. FIGURE 2-54: SD RECORD HANDLER SETTINGS 1. Check to enable SD Record Handler for Alarm, Motions 1 through 4, Sabotage Detection, Schedule, Audio Detection, Object Detection, Adaptive Motion, Directional Motion, and Object Removal.
saving it. Viewing SD Card Files from a Remote Server 1. Configure the SD Record Handler for Alarm, Motions 1 through 4, Sabotage Detection, Schedule, Audio Detection, Object Detection, Adaptive Motion, Directional Motion, and Object Removal. 2. Type “ftp://” followed by the IP address of the camera in a Web browser or Windows Explorer. 3. Right-click on a snapshot or recording from the SD card and save the file locally or open the file to view its content. Format SD card as FAT32 1.
FIGURE 2-56: FAT32 FORMAT COMPLETE 2.2.6.3 SMTP Notification Handler Set detailed SMTP Notification Handler function that will send an email to predefined email addresses when any or all the selected events are activated. NOTE: To use email notification, the camera must be connected to a local area network (LAN) that maintains an SMTP mail server. Consult your network administrator for information on configuring email notification on your local network.
SMTP Notification Handler 1. Check the Enabled button to enable SMTP Notification Handler for Alarm, Motions 1 through 4, Sabotage Detection, Audio Detection, Object Detection, Adaptive Motion, Directional Motion, and Object Removal. 2. Click in the text boxes (Message, From, and Subject), and then type the necessary information in each text box. 3. Select the Attach JPEG Snapshot box if you want to send a JPEG as an attachment. 4. Continue to set the SMTP Server and Address List.
2.2.6.4 Sound Notification Handler This page is designed for configuring detailed settings for sound notifications when an event occurs. FIGURE 2-58: SOUND NOTIFICATION HANDLER SETTINGS Sound Notification Handler 1. Select the level ranging from High, Mid to Low for sound notification handlers of different events. 2.
(with “none” displayed when no file is uploaded) and the Delete button will be enabled. Click on Delete to delete the file if necessary. 3. Click the Save button to save the settings, or click the Reset button to clear all of the information you entered without saving it. 2.2.6.5 OSD Handler OSD Handler allows user to enable “On Screen Display” settings, which triggers text to be displayed in live view when any or all the selected events are selected.
Pelco Troubleshooting Contact Information If the instructions provided fail to solve your problem, contact Pelco Product Support at 1-800-289-9100 (USA and Canada) or +1-559-292-1981 (international) for assistance. Be sure to have the serial number available when calling. Do not try to repair the unit yourself. Leave maintenance and repairs to qualified technical personnel only.
Pelco 625 W. Alluvial Fresno, California 93711 United States (800) 289-9100 USA & Canada Phone (800) 289-9150 USA & Canada Fax +1 (559) 292-1981 International Phone +1 (559) 348-1120 International Fax www.pelco.com Pelco, the Pelco logo, and other trademarks associated with Pelco products referred to in this publication are trademarks of Pelco, Inc. or its affiliates. ONVIF and the ONVIF logos are trademarks of ONVIF Inc. All other product names and services are the property of their respective companies.
