Quick Start Guide

INTRODUCTION
The NET5500 Series video encoder is a network-based channel encoder with a built-in, Web-based viewer for live streaming to a
standard Web browser (Microsoft® Internet Explorer®, Chrome®, Safari® or Mozilla® Firefox®). The encoder is built upon open
standards and is part of an Endura® system for recording, managing, administering, and viewing video streams.
The encoder supports H.264 and MJPEG compression. It can generate two independently configurable H.264 streams, each up
to D1 resolution (720 x 480 for NTSC, 720 x 576 for PAL) and 30/25 images per second (ips) in addition to an MJPEG stream for
Web viewing.
The NET5500 can be configured for one alarm input for each video channel. When an alarm event is triggered, the unit can send
a message to an operator, and trigger a relay.
The unit also supports motion detection for each video channel. You can configure one motion zone, each with its own independent
sensitivity and threshold settings. When the NET5500 detects activity in any of these areas, it can trigger an alarm event.
The video encoder supports one audio input for each video channel over the network. The system operator (security personnel)
can see and hear activity in any target area in which a microphone is present.
The NET5500 supports control of remote peripherals such as pan/tilt/zoom (PTZ) cameras by way of D-Protocol, P-Protocol, and
Coaxitron® protocols.
Models
~
NET5501 One-channel H.264 rack encoder
~
NET5504 Four-channel H.264 rack encoder
~
NET5508 Eight-channel H.264 rack encoder
~
NET5516 Sixteen-channel H.264 rack encoder
Getting Started
Before installing your device, thoroughly familiarize yourself with the information in the installation section of this manual.
NOTES
~
Pelco recommends connecting the device to a network that uses a Dynamic Host Configuration Protocol (DHCP) server
to address devices.
~
Do not use a network hub when configuring the network settings for the device.
~
To ensure secure access, place the device behind a firewall when it is connected to a network.
SUPPLIED PARTS LIST
NET5501
Installation Manual, Safety Instruction (2ea) / Resource Disc (1ea) / Adapter (1ea) / Rubber Feet (4ea) / Rack Mount Ear (2ea) /
Cable Clamp (1ea) / Screw (2ea) for Cable Clamp binding 1 plus 1 spare / Screw (3ea) for Rack Mount Bracket / Screw (4ea) for
Product Rack binding / 5-Pin Terminal Block (2ea)
NET5504
Installation Manual, Safety Instruction (2ea) / Resource Disc (1ea) / Adapter (1ea) / Rubber Feet (4ea) / Rack Mount Ear (2ea) /
Cable Clamp (1ea) / Screw (2ea) for Cable Clamp binding 1 plus 1 spare / Screw (3ea) for Rack Mount Bracket / Screw (4ea) for
Product Rack binding / 6-Pin Terminal Block (2ea)
NET5508
Installation Manual, Safety Instruction (2ea) / Resource Disc (1ea) / Adapter (1ea) / Rubber Feet (4ea) / Rack Mount Ear (2ea) /
Cable Clamp (1ea) / Screw (2ea) for Cable Clamp binding 1 plus 1 spare / Screw (3ea) for Rack Mount Bracket / Screw (4ea) for
Product Rack binding / 10-Pin Terminal Block (2ea) / Dust Filter (1ea)
NET5516
Installation Manual, Safety Instruction (2ea) / Resource Disc (1ea) / Adapter (1ea) / Rubber Feet (4ea) / Rack Mount Ear (2ea) /
Cable Clamp (1ea) / Screw (2ea) for Cable Clamp binding 1 plus 1 spare / Screw (3ea) for Rack Mount Bracket / Screw (4ea) for
Product Rack binding / 8-Pin Terminal Block (2ea) / 10-Pin Terminal Block (2ea) / Dust Filter (1ea)
English
|
5