NET5500 Series VIDEO ENCODER Quick Start Guide English NET5501 NET5504 NET5508 NET5516 C5653M-A (10/14)
Important Safety Instructions 1. Read these instructions. 3. Heed all warnings. 2. 4. 5. 6. 7. 8. 9. Keep these instructions. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
Important Notices REGULATORY NOTICES This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. RADIO AND TELEVISION INTERFERENCE This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the FCC rules.
CCC POWER CORD STATEMENT Models shipped to China do not include power cords. Note : A CCC approved power cord must be used to power the equipment when used in China. Korean Class A EMC 이 기기는 업무용 (A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하시길 바라며, 가정 외의 지역에서 사용하는 것을 목적으로 합니다. This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures. ESD WARNING WARNING: This product is sensitive to Electrostatic Discharge (ESD).
INTRODUCTION The NET5500 Series video encoder is a network-based channel encoder with a built-in, Web-based viewer for live streaming to a standard Web browser (Microsoft® Internet Explorer®, Chrome®, Safari® or Mozilla® Firefox®). The encoder is built upon open standards and is part of an Endura® system for recording, managing, administering, and viewing video streams. The encoder supports H.264 and MJPEG compression. It can generate two independently configurable H.
Front Panel Description NET5501/NET5504 NET5500 Series Video Encoder a NET5508/NET5516 NET5500 Series Video Encoder a No. Name Description Displays power On/Off status. It glows blue when the unit has power. Displays network status (connection and speed). Off : The unit is not connected to the network. Solid amber : The unit is connected to the network using the 100 Mbps standard. Solid red : The unit is connected to the network using the 10 Mbps standard.
Rear Panel Description NET5501 A NO COM Tx+ Rx+ 1 1 NC Tx- Rx- a b c d ef g NET5504 A1 A2 NO COM Tx+ Rx+ A3 A4 a NC Tx- Rx- b c 1 2 3 4 1 2 3 4 d f 1 3 2 4 g e NET5508 Tx+ Tx- NO1 COM1 NC1 A1 A2 A3 A4 Rx+ Rx- NO2 COM2 NC2 A5 A6 A7 A8 a b c 1 3 5 7 2 4 6 8 d 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 f e g NET5516 Tx+Tx- NO1 COM1 NC1 A1 A2 Rx+ Rx- NO2 COM2 NC2 A5 A6 a b A3 A4 A7 A8 NO3 COM3 NC3 A9 A10 NO4 COM4 NC4 A13 A14 c A11 A12 A15 A16 d 1 3
A NO COM Tx+ Rx+ 1 A NO COM Tx+Description Rx+ No. Name Power input socket. For connection of 12V adapter. b Press this switch to reset device to the factory default. If you perform the factory reset, all your settings to device will be lost. NC Tx- Rx- c A NO COM Tx+ Rx+ Alarm input sensor terminal NO/NC Relay control COM Relay common TX+/TX- RS-422 and RS-485 Data lines RS-422 RX Data line 1 RX+/RX- A NO COM Tx+ Rx+ JJ Disabled in RS-485 mode. NC Tx-Ground Rx-terminal.
Mounting in a rack The NET5500 Series encoder mounts into an industry-standard 48 cm (19-inch) equipment rack. The NET5500 Series encoder occupies 1 RU (4.45 cm or 1.75 inches) of vertical rack space. The hardware necessary to mount the NET5500 Series encoder into a rack is supplied with the unit. The rack must meet the following requirements Rack standard : 48 cm (19 inches), EIA-310-D compliant (rear column required) Rack column depth : 50.8 to 76.
Accessing the Encoder and Attached Cameras The first time you access the camera, the live video page appears. By default, you are viewing the video as a public user and only have access to the single stream live view. If, for security purposes, users should not be allowed to view video without first logging on to the camera, change the permissions for public users.
No. c Name Description Multi-Function Image Button + Pan Right _ Pan Left Home Preset d Control the Zoom Activates Zoom in (-) / Zoom out (+) features. e Control the Focus Activates Near (-) / Far (+) features. f Control the Iris Adjusts the camera brightness. g Move to Presets Moves to the preset selected. h Pattern Activates the pattern selected.
Pelco by Schneider Electric 3500 Pelco Way Clovis, California 93612-5699 United States USA & Canada Tel (800) 289-9100 Fax (800) 289-9150 International Tel +1 (559) 292-1981 Fax +1 (559) 348-1120 www.pelco.com www.pelco.
